diff mbox series

[v9,09/10] ARM: dts: stm32: add STM32MP1-based Phytec SoM

Message ID 20230505060158.16516-10-s.trumtrar@pengutronix.de (mailing list archive)
State New, archived
Headers show
Series ARM: stm32: add support for Phycore STM32MP1 | expand

Commit Message

Steffen Trumtrar May 5, 2023, 6:01 a.m. UTC 
The Phytec STM32MP1 based SoMs feature up to 1 GB DDR3LP RAM, up to 1 GB
eMMC, up to 16 MB QSPI and up to 128 GB NAND flash.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---

Notes:
    Changes since v7:
      - remove unused gpu_reservde memory range
      - get rid of duplicate ethernet clock assignments
    
    Changes since v6:
      - rename mdio0->mdio
    
    Changes since v5:
      - cleanup dt_bindings_check warnings
    
    Changes since v4:
      - cleanup usage of "status = okay|disabled"
      - fix remaining non-generic node names
      - rework sai nodes to not duplicate the existing settings in stm32mp151.dtsi
    
    Changes since v3:
      - cleanup board-compatible
      - cleanup aliases
      - rename nodes according to schema
      - use interrupt flag

 .../stm32mp157c-phycore-stm32mp15-som.dtsi    | 577 ++++++++++++++++++
 1 file changed, 577 insertions(+)
 create mode 100644 arch/arm/boot/dts/stm32mp157c-phycore-stm32mp15-som.dtsi
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp15-som.dtsi b/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp15-som.dtsi
new file mode 100644
index 000000000000..4e8b2d2b30c7
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-phycore-stm32mp15-som.dtsi
@@ -0,0 +1,577 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022-2023 Steffen Trumtrar <kernel@pengutronix.de>
+ * Copyright (C) Phytec GmbH 2019-2020 - All Rights Reserved
+ * Author: Dom VOVARD <dom.vovard@linrt.com>.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "stm32mp15-pinctrl.dtsi"
+
+/ {
+	model = "PHYTEC phyCORE-STM32MP15 SOM";
+	compatible = "phytec,phycore-stm32mp157c-som", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		rtc0 = &i2c4_rtc;
+		rtc1 = &rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-home {
+			label = "Home";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+		};
+
+		key-enter {
+			label = "Enter";
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_ENTER>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		label = "STM32MP1-PHYCORE";
+		routing =
+			"Playback", "MCLK", /* Set a route between "MCLK" and "playback" widgets */
+			"Capture", "MCLK";
+		dais = <&sai2b_port>,
+		       <&sai2a_port>;
+	};
+
+	regulator_vin: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vin";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&ethernet0 {
+	pinctrl-0 = <&ethernet0_rgmii_pins_d>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_d>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+	st,eth-clk-sel;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			interrupt-parent = <&gpiog>;
+			interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,min-output-impedance;
+			enet-phy-lane-no-swap;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_b>;
+	pinctrl-1 = <&i2c1_sleep_pins_b>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "okay";
+
+	codec@18 {
+		compatible = "ti,tlv320aic3007";
+		reg = <0x18>;
+		#sound-dai-cells = <0>;
+
+		ai3x-micbias-vg = <2>;
+
+		AVDD-supply = <&v3v3>;
+		IOVDD-supply = <&v3v3>;
+		DRVDD-supply = <&v3v3>;
+		DVDD-supply = <&v1v8_audio>;
+
+		clocks = <&sai2b>;
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tlv320_tx_endpoint: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&sai2b_endpoint>;
+				frame-master;
+				bitclock-master;
+			};
+
+			tlv320_rx_endpoint: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&sai2a_endpoint>;
+				frame-master;
+				bitclock-master;
+			};
+		};
+	};
+
+	touch@44 {
+		compatible = "st,stmpe811";
+		reg = <0x44>;
+		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpioi>;
+		vio-supply = <&v3v3>;
+		vcc-supply = <&v3v3>;
+
+		touchscreen {
+			compatible = "st,stmpe-ts";
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <1>;
+			st,touch-det-delay = <2>;
+			st,settling = <2>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
+		};
+	};
+
+	leds@62 {
+		compatible = "nxp,pca9533";
+		reg = <0x62>;
+
+		led-0 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_POWER;
+			type = <PCA9532_TYPE_LED>;
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_POWER;
+			type = <PCA9532_TYPE_LED>;
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_HEARTBEAT;
+			type = <PCA9532_TYPE_LED>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&i2c4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+
+	pmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			buck1-supply = <&regulator_vin>;
+			buck2-supply = <&regulator_vin>;
+			buck3-supply = <&regulator_vin>;
+			buck4-supply = <&regulator_vin>;
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo4-supply = <&regulator_vin>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			boost-supply = <&regulator_vin>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+
+			};
+
+			vdd_eth_2v5: ldo2 {
+				regulator-name = "dd_eth_2v5";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdda: ldo5 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			vdd_eth_1v0: ldo6 {
+				regulator-name = "vdd_eth_1v0";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+				regulator-active-discharge = <1>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>,
+				     <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling",
+					  "onkey-rising";
+			power-off-time-sec = <10>;
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+		};
+	};
+
+	i2c4_eeprom: eeprom@50 {
+		compatible = "microchip,24c32",
+			     "atmel,24c32";
+		reg = <0x50>;
+	};
+
+	i2c4_rtc: rtc@52 {
+		compatible = "microcrystal,rv3028";
+		reg = <0x52>;
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_b>, <&sai2b_pins_d>;
+	pinctrl-1 = <&sai2a_sleep_pins_b>, <&sai2b_sleep_pins_d>;
+	status = "okay";
+};
+
+&sai2a {
+	dma-names = "rx";
+	st,sync = <&sai2b 2>;
+	clocks = <&rcc SAI2_K>, <&sai2b>;
+	clock-names = "sai_ck", "MCLK";
+	#clock-cells = <0>;
+
+	sai2a_port: port {
+		sai2a_endpoint: endpoint {
+			remote-endpoint = <&tlv320_rx_endpoint>;
+			mclk-fs = <256>;
+			dai-tdm-slot-num = <2>;
+			dai-tdm-slot-width = <16>;
+		};
+	};
+};
+
+&sai2b {
+	dma-names = "tx";
+	#clock-cells = <0>;
+
+	sai2b_port: port {
+		sai2b_endpoint: endpoint {
+			remote-endpoint = <&tlv320_tx_endpoint>;
+			mclk-fs = <256>;
+			dai-tdm-slot-num = <2>;
+			dai-tdm-slot-width = <16>;
+		};
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_b>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_b>;
+	cd-gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_e>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_e>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_e>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
+};
+
+&spi1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi1_pins_a>;
+	pinctrl-1 = <&spi1_sleep_pins_a>;
+	cs-gpios = <&gpioz 3 0>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	pinctrl-3 = <&uart4_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usart1 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart1_pins_b &usart1_pins_a>;
+	pinctrl-1 = <&usart1_sleep_pins_b &usart1_sleep_pins_a>;
+	pinctrl-2 = <&usart1_idle_pins_b &usart1_idle_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usart3 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart3_pins_a>;
+	pinctrl-1 = <&usart3_sleep_pins_a>;
+	pinctrl-2 = <&usart3_idle_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbh_ohci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};