| Message ID | 20230630121059.28748-4-zelong.dong@amlogic.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | reset: meson-c3: add reset driver | expand |
Hello Zelong, Thanks a lot for the patch, please find my comments below. On Fri, Jun 30, 2023 at 08:10:59PM +0800, zelong dong wrote: > From: Zelong Dong <zelong.dong@amlogic.com> > > Add the reset controller device of Meson-C3 SoC family > > Signed-off-by: Zelong Dong <zelong.dong@amlogic.com> > --- > arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi | 7 +++++++ > 1 file changed, 7 insertions(+) > > diff --git a/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi b/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi > index 60ad4f3eef9d..62684b7a684c 100644 > --- a/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi > +++ b/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi > @@ -6,6 +6,7 @@ > #include <dt-bindings/interrupt-controller/irq.h> > #include <dt-bindings/interrupt-controller/arm-gic.h> > #include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/reset/amlogic,meson-c3-reset.h> > > / { > cpus { > @@ -82,6 +83,12 @@ uart_b: serial@7a000 { > clock-names = "xtal", "pclk", "baud"; > }; > > + reset: reset-controller@0x2000 { > + compatible = "amlogic,meson-c3-reset"; > + reg = <0x0 0x2000 0x0 0x98>; > + #reset-cells = <1>; > + }; > + As Martin mentioned in the my review, internal apb entries should be sorted by base reg offset. So reset-controller must be located before uart_b. Please refer to: https://lore.kernel.org/linux-amlogic/CAFBinCAO14zcgY66UyJO9UxuCWf1N-Lsx=iYNTJL=cwXoJv__Q@mail.gmail.com/ > }; > }; > }; > -- > 2.35.1 > > > _______________________________________________ > linux-amlogic mailing list > linux-amlogic@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-amlogic
On 30/06/2023 14:10, zelong dong wrote: > From: Zelong Dong <zelong.dong@amlogic.com> > > Add the reset controller device of Meson-C3 SoC family > > Signed-off-by: Zelong Dong <zelong.dong@amlogic.com> > --- > arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi | 7 +++++++ > 1 file changed, 7 insertions(+) > > diff --git a/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi b/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi > index 60ad4f3eef9d..62684b7a684c 100644 > --- a/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi > +++ b/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi > @@ -6,6 +6,7 @@ > #include <dt-bindings/interrupt-controller/irq.h> > #include <dt-bindings/interrupt-controller/arm-gic.h> > #include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/reset/amlogic,meson-c3-reset.h> > > / { > cpus { > @@ -82,6 +83,12 @@ uart_b: serial@7a000 { > clock-names = "xtal", "pclk", "baud"; > }; > > + reset: reset-controller@0x2000 { Please drop 0x, the node name should be: reset-controller@2000 Thanks, Neil > + compatible = "amlogic,meson-c3-reset"; > + reg = <0x0 0x2000 0x0 0x98>; > + #reset-cells = <1>; > + }; > + > }; > }; > };
diff --git a/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi b/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi index 60ad4f3eef9d..62684b7a684c 100644 --- a/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi +++ b/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi @@ -6,6 +6,7 @@ #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/reset/amlogic,meson-c3-reset.h> / { cpus { @@ -82,6 +83,12 @@ uart_b: serial@7a000 { clock-names = "xtal", "pclk", "baud"; }; + reset: reset-controller@0x2000 { + compatible = "amlogic,meson-c3-reset"; + reg = <0x0 0x2000 0x0 0x98>; + #reset-cells = <1>; + }; + }; }; };