@@ -35,6 +35,7 @@
#define DWMAC_CORE_5_10 0x51
#define DWMAC_CORE_5_20 0x52
#define DWXGMAC_CORE_2_10 0x21
+#define DWXGMAC_CORE_2_20 0x22
#define DWXLGMAC_CORE_2_00 0x20
/* Device ID */
@@ -62,11 +62,16 @@ static void stmmac_xgmac2_c45_format(struct stmmac_priv *priv, int phyaddr,
static void stmmac_xgmac2_c22_format(struct stmmac_priv *priv, int phyaddr,
int phyreg, u32 *hw_addr)
{
- u32 tmp;
+ u32 tmp = 0;
+ if (priv->synopsys_id < DWXGMAC_CORE_2_20) {
+ /* Until ver 2.20 XGMAC does not support C22 addr >= 4. Those
+ * bits above bit 3 of XGMAC_MDIO_C22P register are reserved.
+ */
+ tmp = readl(priv->ioaddr + XGMAC_MDIO_C22P);
+ tmp &= ~MII_XGMAC_C22P_MASK;
+ }
/* Set port as Clause 22 */
- tmp = readl(priv->ioaddr + XGMAC_MDIO_C22P);
- tmp &= ~MII_XGMAC_C22P_MASK;
tmp |= BIT(phyaddr);
writel(tmp, priv->ioaddr + XGMAC_MDIO_C22P);
@@ -132,8 +137,9 @@ static int stmmac_xgmac2_mdio_read_c22(struct mii_bus *bus, int phyaddr,
priv = netdev_priv(ndev);
- /* HW does not support C22 addr >= 4 */
- if (phyaddr > MII_XGMAC_MAX_C22ADDR)
+ /* Until ver 2.20 XGMAC does not support C22 addr >= 4 */
+ if (priv->synopsys_id < DWXGMAC_CORE_2_20 &&
+ phyaddr > MII_XGMAC_MAX_C22ADDR)
return -ENODEV;
stmmac_xgmac2_c22_format(priv, phyaddr, phyreg, &addr);
@@ -209,8 +215,9 @@ static int stmmac_xgmac2_mdio_write_c22(struct mii_bus *bus, int phyaddr,
priv = netdev_priv(ndev);
- /* HW does not support C22 addr >= 4 */
- if (phyaddr > MII_XGMAC_MAX_C22ADDR)
+ /* Until ver 2.20 XGMAC does not support C22 addr >= 4 */
+ if (priv->synopsys_id < DWXGMAC_CORE_2_20 &&
+ phyaddr > MII_XGMAC_MAX_C22ADDR)
return -ENODEV;
stmmac_xgmac2_c22_format(priv, phyaddr, phyreg, &addr);
@@ -551,13 +558,18 @@ int stmmac_mdio_register(struct net_device *ndev)
new_bus->read_c45 = &stmmac_xgmac2_mdio_read_c45;
new_bus->write_c45 = &stmmac_xgmac2_mdio_write_c45;
- /* Right now only C22 phys are supported */
- max_addr = MII_XGMAC_MAX_C22ADDR + 1;
+ if (priv->synopsys_id < DWXGMAC_CORE_2_20) {
+ /* Right now only C22 phys are supported */
+ max_addr = MII_XGMAC_MAX_C22ADDR + 1;
- /* Check if DT specified an unsupported phy addr */
- if (priv->plat->phy_addr > MII_XGMAC_MAX_C22ADDR)
- dev_err(dev, "Unsupported phy_addr (max=%d)\n",
+ /* Check if DT specified an unsupported phy addr */
+ if (priv->plat->phy_addr > MII_XGMAC_MAX_C22ADDR)
+ dev_err(dev, "Unsupported phy_addr (max=%d)\n",
MII_XGMAC_MAX_C22ADDR);
+ } else {
+ /* XGMAC version 2.20 onwards support 32 phy addr */
+ max_addr = PHY_MAX_ADDR;
+ }
} else {
new_bus->read = &stmmac_mdio_read_c22;
new_bus->write = &stmmac_mdio_write_c22;
For XGMAC versions < 2.2 number of supported mdio C22 addresses is restricted to 3. From XGMAC version 2.2 there are no restrictions on the C22 addresses, it supports all valid mdio addresses(0 to 31). Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com> --- drivers/net/ethernet/stmicro/stmmac/common.h | 1 + .../net/ethernet/stmicro/stmmac/stmmac_mdio.c | 36 ++++++++++++------- 2 files changed, 25 insertions(+), 12 deletions(-)