| Message ID | 20230801141920.3317697-1-u-kumar1@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | arm64: dts: ti: k3-j784s4-evm: Correct Pin mux offset for ospi | expand |
On 19:49-20230801, Udit Kumar wrote: > After splitting wkup_pmx pin mux for J784S4 into four regions. > Pin mux offset for OSPI nodes were not updated to align with new > regions, due to this while setting ospi pin muxes out of range > error was seen. > > Pin mux offsets for OSPI nodes are corrected in this patch. > > Fixes: 14462bd0b247 ("arm64: dts: ti: k3-j784s4: Fix wakeup pinmux range and pinctrl node offsets") I think the rename of pinnodes will get in the way of the automatic fixup in stable flow. > Signed-off-by: Udit Kumar <u-kumar1@ti.com> > --- > Original test log > https://gist.github.com/uditkumarti/85b5076df99c3019aa56da4268724295 > line 1104 and 1107, out of range error is seen > > Test log with patch > https://gist.github.com/uditkumarti/29b424d0a1527e77947f72d2e8a38f01 > > arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 31 +++++++++++++++--------- > 1 file changed, 19 insertions(+), 12 deletions(-) > > diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts > index 7ad152a1b90f..1961cd819f5e 100644 > --- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts > +++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts > @@ -379,21 +379,28 @@ J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */ > J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */ > J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */ > J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */ > - J784S4_WKUP_IOPAD(0x03c, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_CSn3.MCU_OSPI0_ECC_FAIL */ > - J784S4_WKUP_IOPAD(0x038, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_CSn2.MCU_OSPI0_RESET_OUT0 */ > + >; > + }; > +}; > + > +&wkup_pmx1 { > + mcu_fss0_ospi0_pins1_default: mcu-fss0-ospi0-default-pins1 { ^^^ and below: > + pinctrl-single,pins = < > + J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */ > + J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */ > >; > }; > > - mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins { > + mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default { Please run your check against https://lore.kernel.org/all/20230721082654.27036-1-tony@atomide.com/ > pinctrl-single,pins = < > - J784S4_WKUP_IOPAD(0x040, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */ > - J784S4_WKUP_IOPAD(0x05c, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */ > - J784S4_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */ > - J784S4_WKUP_IOPAD(0x050, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */ > - J784S4_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */ > - J784S4_WKUP_IOPAD(0x058, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */ > - J784S4_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */ > - J784S4_WKUP_IOPAD(0x044, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */ > + J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */ > + J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */ > + J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */ > + J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */ > + J784S4_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */ > + J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */ > + J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */ > + J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */ > >; > }; > }; > @@ -437,7 +444,7 @@ &fss { > &ospi0 { > status = "okay"; > pinctrl-names = "default"; > - pinctrl-0 = <&mcu_fss0_ospi0_pins_default>; > + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_pins1_default>; > > flash@0 { > compatible = "jedec,spi-nor"; > -- > 2.34.1 >
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts index 7ad152a1b90f..1961cd819f5e 100644 --- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts +++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts @@ -379,21 +379,28 @@ J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */ J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */ - J784S4_WKUP_IOPAD(0x03c, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_CSn3.MCU_OSPI0_ECC_FAIL */ - J784S4_WKUP_IOPAD(0x038, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_CSn2.MCU_OSPI0_RESET_OUT0 */ + >; + }; +}; + +&wkup_pmx1 { + mcu_fss0_ospi0_pins1_default: mcu-fss0-ospi0-default-pins1 { + pinctrl-single,pins = < + J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */ + J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */ >; }; - mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins { + mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default { pinctrl-single,pins = < - J784S4_WKUP_IOPAD(0x040, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */ - J784S4_WKUP_IOPAD(0x05c, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */ - J784S4_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */ - J784S4_WKUP_IOPAD(0x050, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */ - J784S4_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */ - J784S4_WKUP_IOPAD(0x058, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */ - J784S4_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */ - J784S4_WKUP_IOPAD(0x044, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */ + J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */ + J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */ + J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */ + J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */ + J784S4_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */ + J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */ + J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */ + J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */ >; }; }; @@ -437,7 +444,7 @@ &fss { &ospi0 { status = "okay"; pinctrl-names = "default"; - pinctrl-0 = <&mcu_fss0_ospi0_pins_default>; + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_pins1_default>; flash@0 { compatible = "jedec,spi-nor";
After splitting wkup_pmx pin mux for J784S4 into four regions. Pin mux offset for OSPI nodes were not updated to align with new regions, due to this while setting ospi pin muxes out of range error was seen. Pin mux offsets for OSPI nodes are corrected in this patch. Fixes: 14462bd0b247 ("arm64: dts: ti: k3-j784s4: Fix wakeup pinmux range and pinctrl node offsets") Signed-off-by: Udit Kumar <u-kumar1@ti.com> --- Original test log https://gist.github.com/uditkumarti/85b5076df99c3019aa56da4268724295 line 1104 and 1107, out of range error is seen Test log with patch https://gist.github.com/uditkumarti/29b424d0a1527e77947f72d2e8a38f01 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 31 +++++++++++++++--------- 1 file changed, 19 insertions(+), 12 deletions(-)