@@ -252,7 +252,9 @@ vdd_sd_dv: regulator-TLV71033 {
};
&main_pmx0 {
+ bootph-all;
main_uart8_pins_default: main-uart8-default-pins {
+ bootph-all;
pinctrl-single,pins = <
J784S4_IOPAD(0x040, PIN_INPUT, 14) /* (AF37) MCASP0_AXR0.UART8_CTSn */
J784S4_IOPAD(0x044, PIN_OUTPUT, 14) /* (AG37) MCASP0_AXR1.UART8_RTSn */
@@ -269,6 +271,7 @@ J784S4_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AP37) I2C0_SDA */
};
main_mmc1_pins_default: main-mmc1-default-pins {
+ bootph-all;
pinctrl-single,pins = <
J784S4_IOPAD(0x104, PIN_INPUT, 0) /* (AB38) MMC1_CLK */
J784S4_IOPAD(0x108, PIN_INPUT, 0) /* (AB36) MMC1_CMD */
@@ -289,7 +292,9 @@ J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */
};
&wkup_pmx2 {
+ bootph-all;
wkup_uart0_pins_default: wkup-uart0-default-pins {
+ bootph-all;
pinctrl-single,pins = <
J721S2_WKUP_IOPAD(0x070, PIN_INPUT, 0) /* (L37) WKUP_GPIO0_6.WKUP_UART0_CTSn */
J721S2_WKUP_IOPAD(0x074, PIN_INPUT, 0) /* (L36) WKUP_GPIO0_7.WKUP_UART0_RTSn */
@@ -299,6 +304,7 @@ J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (K34) WKUP_UART0_TXD */
};
wkup_i2c0_pins_default: wkup-i2c0-default-pins {
+ bootph-all;
pinctrl-single,pins = <
J721S2_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */
J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
@@ -306,6 +312,7 @@ J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
};
mcu_uart0_pins_default: mcu-uart0-default-pins {
+ bootph-all;
pinctrl-single,pins = <
J784S4_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (H37) WKUP_GPIO0_14.MCU_UART0_CTSn */
J784S4_WKUP_IOPAD(0x094, PIN_OUTPUT, 0) /* (K37) WKUP_GPIO0_15.MCU_UART0_RTSn */
@@ -366,7 +373,9 @@ J784S4_WKUP_IOPAD(0x170, PIN_INPUT, 0) /* (Y36) MCU_ADC1_AIN7 */
};
&wkup_pmx0 {
+ bootph-all;
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
+ bootph-all;
pinctrl-single,pins = <
J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
@@ -384,7 +393,9 @@ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
};
&wkup_pmx1 {
+ bootph-all;
mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
+ bootph-all;
pinctrl-single,pins = <
J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */
J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */
@@ -392,6 +403,7 @@ J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */
};
mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
+ bootph-all;
pinctrl-single,pins = <
J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */
J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */
@@ -406,6 +418,7 @@ J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */
};
&wkup_uart0 {
+ bootph-all;
/* Firmware usage */
status = "reserved";
pinctrl-names = "default";
@@ -413,6 +426,7 @@ &wkup_uart0 {
};
&wkup_i2c0 {
+ bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&wkup_i2c0_pins_default>;
@@ -426,12 +440,14 @@ eeprom@50 {
};
&mcu_uart0 {
+ bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_uart0_pins_default>;
};
&main_uart8 {
+ bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&main_uart8_pins_default>;
@@ -442,15 +458,18 @@ &ufs_wrapper {
};
&fss {
+ bootph-all;
status = "okay";
};
&ospi0 {
+ bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
flash@0 {
+ bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <8>;
@@ -498,6 +517,7 @@ partition@800000 {
};
partition@3fc0000 {
+ bootph-all;
label = "ospi.phypattern";
reg = <0x3fc0000 0x40000>;
};
@@ -506,11 +526,13 @@ partition@3fc0000 {
};
&ospi1 {
+ bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
flash@0 {
+ bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <1>;
@@ -558,6 +580,7 @@ partition@800000 {
};
partition@3fc0000 {
+ bootph-all;
label = "qspi.phypattern";
reg = <0x3fc0000 0x40000>;
};
@@ -602,6 +625,7 @@ exp2: gpio@22 {
};
&main_sdhci0 {
+ bootph-all;
/* eMMC */
status = "okay";
non-removable;
@@ -610,6 +634,7 @@ &main_sdhci0 {
};
&main_sdhci1 {
+ bootph-all;
/* SD card */
status = "okay";
pinctrl-0 = <&main_mmc1_pins_default>;
Add bootph-all property for all the nodes that are used in SPL stage along with later boot stages. These bootph-all properties will be synced later to u-boot j784s4 dts. Signed-off-by: Apurva Nandan <a-nandan@ti.com> --- arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 25 ++++++++++++++++++++++++ 1 file changed, 25 insertions(+)