diff mbox series

[v5,1/2] ARM: dts: aspeed: Minerva: Add Facebook Minerva (AST2600) BMC

Message ID 20230831055030.3958798-2-peteryin.openbmc@gmail.com (mailing list archive)
State New, archived
Headers show
Series *** Add Facebook Minerva (AST2600) BMC *** | expand

Commit Message

PeterYin Aug. 31, 2023, 5:50 a.m. UTC
Add linux device tree entry related to
Minerva specific devices connected to BMC SoC.

Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
---
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/aspeed-bmc-facebook-minerva.dts  | 377 ++++++++++++++++++
 2 files changed, 378 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-minerva.dts

Comments

Krzysztof Kozlowski Aug. 31, 2023, 6:20 a.m. UTC | #1
On 31/08/2023 07:50, Peter Yin wrote:
> Add linux device tree entry related to
> Minerva specific devices connected to BMC SoC.
> 
> Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
> ---
>  arch/arm/boot/dts/Makefile                    |   1 +
>  .../boot/dts/aspeed-bmc-facebook-minerva.dts  | 377 ++++++++++++++++++
>  2 files changed, 378 insertions(+)
>  create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-minerva.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 9e1d7bf3cff6..edb0b2105333 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1604,6 +1604,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
>  	aspeed-bmc-facebook-wedge400.dtb \
>  	aspeed-bmc-facebook-yamp.dtb \
>  	aspeed-bmc-facebook-yosemitev2.dtb \
> +	aspeed-bmc-facebook-minerva.dtb \

Third or fourth time: that's not a correct order. This is a nit, but
since you keep ignoring it, I don't believe any other feedback was
applied. Why you did not respond to my comments but just ignored them?


Best regards,
Krzysztof
PeterYin Aug. 31, 2023, 6:34 a.m. UTC | #2
On 8/31/23 14:20, Krzysztof Kozlowski wrote:
> On 31/08/2023 07:50, Peter Yin wrote:
>> Add linux device tree entry related to
>> Minerva specific devices connected to BMC SoC.
>>
>> Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
>> ---
>>   arch/arm/boot/dts/Makefile                    |   1 +
>>   .../boot/dts/aspeed-bmc-facebook-minerva.dts  | 377 ++++++++++++++++++
>>   2 files changed, 378 insertions(+)
>>   create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-minerva.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 9e1d7bf3cff6..edb0b2105333 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -1604,6 +1604,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
>>   	aspeed-bmc-facebook-wedge400.dtb \
>>   	aspeed-bmc-facebook-yamp.dtb \
>>   	aspeed-bmc-facebook-yosemitev2.dtb \
>> +	aspeed-bmc-facebook-minerva.dtb \
> Third or fourth time: that's not a correct order. This is a nit, but
> since you keep ignoring it, I don't believe any other feedback was
> applied. Why you did not respond to my comments but just ignored them?
Sorry, I don't notice this is different file.
>
> Best regards,
> Krzysztof
>
Krzysztof Kozlowski Aug. 31, 2023, 6:44 a.m. UTC | #3
On 31/08/2023 08:34, PeterYin wrote:
> 
> On 8/31/23 14:20, Krzysztof Kozlowski wrote:
>> On 31/08/2023 07:50, Peter Yin wrote:
>>> Add linux device tree entry related to
>>> Minerva specific devices connected to BMC SoC.
>>>
>>> Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
>>> ---
>>>   arch/arm/boot/dts/Makefile                    |   1 +
>>>   .../boot/dts/aspeed-bmc-facebook-minerva.dts  | 377 ++++++++++++++++++
>>>   2 files changed, 378 insertions(+)
>>>   create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-minerva.dts
>>>
>>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>>> index 9e1d7bf3cff6..edb0b2105333 100644
>>> --- a/arch/arm/boot/dts/Makefile
>>> +++ b/arch/arm/boot/dts/Makefile
>>> @@ -1604,6 +1604,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
>>>   	aspeed-bmc-facebook-wedge400.dtb \
>>>   	aspeed-bmc-facebook-yamp.dtb \
>>>   	aspeed-bmc-facebook-yosemitev2.dtb \
>>> +	aspeed-bmc-facebook-minerva.dtb \
>> Third or fourth time: that's not a correct order. This is a nit, but
>> since you keep ignoring it, I don't believe any other feedback was
>> applied. Why you did not respond to my comments but just ignored them?
> Sorry, I don't notice this is different file.

You just skipped that comment and did not respond to it in your last
private reply... Just like in previous versions. Go through all the
comments from previous versions, not few.

Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9e1d7bf3cff6..edb0b2105333 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1604,6 +1604,7 @@  dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-facebook-wedge400.dtb \
 	aspeed-bmc-facebook-yamp.dtb \
 	aspeed-bmc-facebook-yosemitev2.dtb \
+	aspeed-bmc-facebook-minerva.dtb \
 	aspeed-bmc-ibm-bonnell.dtb \
 	aspeed-bmc-ibm-everest.dtb \
 	aspeed-bmc-ibm-rainier.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-minerva.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-minerva.dts
new file mode 100644
index 000000000000..0bf4e4a7a16c
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-minerva.dts
@@ -0,0 +1,377 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2023 Facebook Inc.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Minerva";
+	compatible = "facebook,minerva-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial0 = &uart1;
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			<&adc1 2>;
+	};
+};
+
+// HOST BIOS Debug
+&uart1 {
+	status = "okay";
+};
+
+// SOL Host Console
+&uart2 {
+	status = "okay";
+	pinctrl-0 = <>;
+};
+
+// SOL BMC Console
+&uart4 {
+	status = "okay";
+	pinctrl-0 = <>;
+};
+
+// BMC Debug Console
+&uart5 {
+	status = "okay";
+};
+
+//MTIA
+&uart6 {
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+	virtual;
+	port=<0x3e8>;
+	sirq = <7>;
+	sirq-polarity = <0>;
+	dma-mode;
+	dma-channel = <12>;
+};
+
+&wdt1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	no-hw-checksum;
+	use-ncsi;
+	ncsi-ctrl,start-redo-probe;
+	ncsi-ctrl,no-channel-monitor;
+	mlx,multi-host;
+	ncsi-package = <1>;
+	ncsi-channel = <1>;
+	ncsi-rexmit = <1>;
+	ncsi-timeout = <2>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+//BIOS Flash
+&spi2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <12000000>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+	};
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&peci0 {
+	status = "okay";
+	clock-frequency = <1000000>;
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	tmp75@4B {
+		compatible = "ti,tmp75";
+		reg = <0x4B>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+// To Debug card
+&i2c14 {
+	status = "okay";
+	multi-master;
+
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	// SCM FRU
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+	// BSM FRU
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+	};
+};
+
+&adc0 {
+	ref_voltage = <2500>;
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	ref_voltage = <2500>;
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc10_default>;
+};
+
+&jtag1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_jtagm_default>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&gpio0 {
+	pinctrl-names = "default";
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"","","","","","FM_ID_LED_N","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","SOL_UART_SET","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"LED_POSTCODE_0","LED_POSTCODE_1",
+			"LED_POSTCODE_2","LED_POSTCODE_3",
+			"LED_POSTCODE_4","LED_POSTCODE_5",
+			"LED_POSTCODE_6","LED_POSTCODE_7",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"FP_SYS_PWRBTN_IN_N","BMC_SYS_PWRBTN_OUT_N",
+			"FP_RST_BTN_IN_N","","","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","";
+};
+
+&sgpiom0 {
+	status = "okay";
+	max-ngpios = <128>;
+	ngpios = <128>;
+	bus-frequency = <2000000>;
+	gpio-line-names =
+	/*in - out - in - out */
+	/*A0-A3 line 0-7*/
+	"","","","","","ENABLE_SENSORS","","",
+	/*A4-A7 line 8-15*/
+	"","","","","","","","",
+	/*B0-B3 line 16-23*/
+	"","","","","","BMC_RST_BTN_OUT_N","","",
+	/*B4-B7 line 24-31*/
+	"","","","","","","","",
+	/*C0-C3 line 32-39*/
+	"","","","","","","","",
+	/*C4-C7 line 40-47*/
+	"","","","","","","","",
+	/*D0-D3 line 48-55*/
+	"","","","","","","","",
+	/*D4-D7 line 56-63*/
+	"","","","","","","","",
+	/*E0-E3 line 64-71*/
+	"","","","","","","","",
+	/*E4-E7 line 72-79*/
+	"","","","","","","","",
+	/*F0-F3 line 80-87*/
+	"","","","","","","","",
+	/*F4-F7 line 88-95*/
+	"","","","","","","","",
+	/*G0-G3 line 96-103*/
+	"","","","","","","","",
+	/*G4-G7 line 104-111*/
+	"","","","","","","","",
+	/*H0-H3 line 112-119*/
+	"","","","","PLD_SYS_POWER_GOOD","","","",
+	/*H4-H7 line 120-127*/
+	"","","","","","","","",
+	/*I0-I3 line 128-135*/
+	"","","","","","","","",
+	/*I4-I7 line 136-143*/
+	"","","","","","","","",
+	/*J0-J3 line 144-151*/
+	"","","PLD_BIOS_POST_CMPLT_N","","","","","",
+	/*J4-J7 line 152-159*/
+	"","","","","","","","",
+	/*K0-K3 line 160-167*/
+	"","","","","","","","",
+	/*K4-K7 line 168-175*/
+	"","","","","","","","",
+	/*L0-L3 line 176-183*/
+	"","","","","","","","",
+	/*L4-L7 line 184-191*/
+	"","","","","","","","",
+	/*M0-M3 line 192-199*/
+	"","","","","","","","",
+	/*M4-M7 line 200-207*/
+	"","","","","","","","",
+	/*N0-N3 line 208-215*/
+	"","","","","","","","",
+	/*N4-N7 line 216-223*/
+	"","","","","","","","",
+	/*O0-O3 line 224-231*/
+	"","","","","","","","",
+	/*O4-O7 line 232-239*/
+	"","","","","","","","",
+	/*P0-P3 line 240-247*/
+	"","","","","","","","",
+	/*P4-P7 line 248-255*/
+	"","","","","","","","";
+};