diff mbox series

[v4,1/9] arm64: dts: ti: k3-j721s2-mcu: Add MCU R5F cluster nodes

Message ID 20230906112422.2846151-2-a-nandan@ti.com (mailing list archive)
State New, archived
Headers show
Series Add R5F and C7x DSP node for K3 J721S2, AM68 and AM69 SoCs | expand

Commit Message

Apurva Nandan Sept. 6, 2023, 11:24 a.m. UTC
The J721S2 SoCs have a dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/cluster in MCU voltage domain. It can be configured at boot
time to be either run in a LockStep mode or in an Asymmetric Multi
Processing (AMP) fashion in Split-mode. These subsystems have 64 KB
each Tightly-Coupled Memory (TCM) internal memories for each core
split between two banks - ATCM and BTCM (further interleaved into
two banks). The TCMs of both Cores are combined in LockStep-mode to
provide a larger 128 KB of memory, but otherwise are functionally
similar to those on J721E SoCs.

Add the DT nodes for the MCU domain R5F cluster/subsystem, the two R5F
cores are added as child nodes to each of the R5F cluster nodes. The
clusters are configured to run in LockStep mode by default, with the
ATCMs enabled to allow the R5 cores to execute code from DDR with
boot-strapping code from ATCM. The inter-processor communication between
the main A72 cores and these processors is achieved through shared memory
and Mailboxes.

The following firmware names are used by default for these cores, and
can be overridden in a board dts file if desired:
  MCU R5FSS0 Core0: j721s2-mcu-r5f0_0-fw (both in LockStep and Split mode)
  MCU R5FSS0 Core1: j721s2-mcu-r5f0_1-fw (needed only in Split mode)

Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
---
 .../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi     | 40 +++++++++++++++++++
 1 file changed, 40 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index 736ec5fa0ea2..d4624d8461b2 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -652,4 +652,44 @@  wkup_vtm0: temperature-sensor@42040000 {
 		power-domains = <&k3_pds 154 TI_SCI_PD_SHARED>;
 		#thermal-sensor-cells = <1>;
 	};
+
+	mcu_r5fss0: r5fss@41000000 {
+		compatible = "ti,j721s2-r5fss";
+		ti,cluster-mode = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x41000000 0x00 0x41000000 0x20000>,
+			 <0x41400000 0x00 0x41400000 0x20000>;
+		power-domains = <&k3_pds 283 TI_SCI_PD_EXCLUSIVE>;
+
+		mcu_r5fss0_core0: r5f@41000000 {
+			compatible = "ti,j721s2-r5f";
+			reg = <0x41000000 0x00010000>,
+			      <0x41010000 0x00010000>;
+			reg-names = "atcm", "btcm";
+			ti,sci = <&sms>;
+			ti,sci-dev-id = <284>;
+			ti,sci-proc-ids = <0x01 0xff>;
+			resets = <&k3_reset 284 1>;
+			firmware-name = "j721s2-mcu-r5f0_0-fw";
+			ti,atcm-enable = <1>;
+			ti,btcm-enable = <1>;
+			ti,loczrama = <1>;
+		};
+
+		mcu_r5fss0_core1: r5f@41400000 {
+			compatible = "ti,j721s2-r5f";
+			reg = <0x41400000 0x00010000>,
+			      <0x41410000 0x00010000>;
+			reg-names = "atcm", "btcm";
+			ti,sci = <&sms>;
+			ti,sci-dev-id = <285>;
+			ti,sci-proc-ids = <0x02 0xff>;
+			resets = <&k3_reset 285 1>;
+			firmware-name = "j721s2-mcu-r5f0_1-fw";
+			ti,atcm-enable = <1>;
+			ti,btcm-enable = <1>;
+			ti,loczrama = <1>;
+		};
+	};
 };