diff mbox series

[tty,v1,73/74] serial: vt8500: Use port lock wrappers

Message ID 20230914183831.587273-74-john.ogness@linutronix.de (mailing list archive)
State New, archived
Headers show
Series None | expand

Commit Message

John Ogness Sept. 14, 2023, 6:38 p.m. UTC
From: Thomas Gleixner <tglx@linutronix.de>

When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.

So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.

All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.

To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.

Converted with coccinelle. No functional change.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 drivers/tty/serial/vt8500_serial.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
diff mbox series

Patch

diff --git a/drivers/tty/serial/vt8500_serial.c b/drivers/tty/serial/vt8500_serial.c
index c5d5c2765119..78a1c1eea11b 100644
--- a/drivers/tty/serial/vt8500_serial.c
+++ b/drivers/tty/serial/vt8500_serial.c
@@ -227,7 +227,7 @@  static irqreturn_t vt8500_irq(int irq, void *dev_id)
 	struct uart_port *port = dev_id;
 	unsigned long isr;
 
-	spin_lock(&port->lock);
+	uart_port_lock(port);
 	isr = vt8500_read(port, VT8500_URISR);
 
 	/* Acknowledge active status bits */
@@ -240,7 +240,7 @@  static irqreturn_t vt8500_irq(int irq, void *dev_id)
 	if (isr & TCTS)
 		handle_delta_cts(port);
 
-	spin_unlock(&port->lock);
+	uart_port_unlock(port);
 
 	return IRQ_HANDLED;
 }
@@ -342,7 +342,7 @@  static void vt8500_set_termios(struct uart_port *port,
 	unsigned int baud, lcr;
 	unsigned int loops = 1000;
 
-	spin_lock_irqsave(&port->lock, flags);
+	uart_port_lock_irqsave(port, &flags);
 
 	/* calculate and set baud rate */
 	baud = uart_get_baud_rate(port, termios, old, 900, 921600);
@@ -410,7 +410,7 @@  static void vt8500_set_termios(struct uart_port *port,
 	vt8500_write(&vt8500_port->uart, 0x881, VT8500_URFCR);
 	vt8500_write(&vt8500_port->uart, vt8500_port->ier, VT8500_URIER);
 
-	spin_unlock_irqrestore(&port->lock, flags);
+	uart_port_unlock_irqrestore(port, flags);
 }
 
 static const char *vt8500_type(struct uart_port *port)