@@ -2520,12 +2520,16 @@ static void mt7530_mac_port_get_caps(struct dsa_switch *ds, int port,
struct phylink_config *config)
{
switch (port) {
- case 0 ... 4: /* Internal phy */
+ /* Internal PHY */
+ case 0 ... 4:
__set_bit(PHY_INTERFACE_MODE_GMII,
config->supported_interfaces);
break;
- case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
+ /* Port 5 which can be used as a CPU port supports rgmii with delays,
+ * mii, and gmii.
+ */
+ case 5:
phy_interface_set_rgmii(config->supported_interfaces);
__set_bit(PHY_INTERFACE_MODE_MII,
config->supported_interfaces);
@@ -2533,7 +2537,8 @@ static void mt7530_mac_port_get_caps(struct dsa_switch *ds, int port,
config->supported_interfaces);
break;
- case 6: /* 1st cpu port */
+ /* Port 6 which can be used as a CPU port supports rgmii and trgmii. */
+ case 6:
__set_bit(PHY_INTERFACE_MODE_RGMII,
config->supported_interfaces);
__set_bit(PHY_INTERFACE_MODE_TRGMII,
@@ -2548,19 +2553,24 @@ static void mt7531_mac_port_get_caps(struct dsa_switch *ds, int port,
struct mt7530_priv *priv = ds->priv;
switch (port) {
- case 0 ... 4: /* Internal phy */
+ /* Internal PHY */
+ case 0 ... 4:
__set_bit(PHY_INTERFACE_MODE_GMII,
config->supported_interfaces);
break;
- case 5: /* 2nd cpu port supports either rgmii or sgmii/8023z */
+ /* Port 5 which can be used as a CPU port supports rgmii with delays on
+ * MT7531BE, sgmii/802.3z on MT7531AE.
+ */
+ case 5:
if (!priv->p5_sgmii) {
phy_interface_set_rgmii(config->supported_interfaces);
break;
}
fallthrough;
- case 6: /* 1st cpu port supports sgmii/8023z only */
+ /* Port 6 which can be used as a CPU port supports sgmii/802.3z. */
+ case 6:
__set_bit(PHY_INTERFACE_MODE_SGMII,
config->supported_interfaces);
__set_bit(PHY_INTERFACE_MODE_1000BASEX,
@@ -2579,11 +2589,13 @@ static void mt7988_mac_port_get_caps(struct dsa_switch *ds, int port,
phy_interface_zero(config->supported_interfaces);
switch (port) {
- case 0 ... 4: /* Internal phy */
+ /* Internal PHY */
+ case 0 ... 4:
__set_bit(PHY_INTERFACE_MODE_INTERNAL,
config->supported_interfaces);
break;
+ /* Port 6 which can be used as a CPU port is an internal 10G port. */
case 6:
__set_bit(PHY_INTERFACE_MODE_INTERNAL,
config->supported_interfaces);
@@ -2747,12 +2759,12 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
u32 mcr_cur, mcr_new;
switch (port) {
- case 0 ... 4: /* Internal phy */
+ case 0 ... 4:
if (state->interface != PHY_INTERFACE_MODE_GMII &&
state->interface != PHY_INTERFACE_MODE_INTERNAL)
goto unsupported;
break;
- case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
+ case 5:
if (priv->p5_interface == state->interface)
break;
@@ -2762,7 +2774,7 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
if (priv->p5_intf_sel != P5_DISABLED)
priv->p5_interface = state->interface;
break;
- case 6: /* 1st cpu port */
+ case 6:
if (priv->p6_interface == state->interface)
break;
There's no logic to numerically order the CPU ports. State the port number and its capability of being used as a CPU port instead. Remove the irrelevant PHY muxing information from mt7530_mac_port_get_caps(). Explain the supported MII modes instead. Remove the out of place PHY muxing information from mt753x_phylink_mac_config(). The function is for MT7530, MT7531, and the switch on the MT7988 SoC but there's no PHY muxing on MT7531 or the switch on the MT7988 SoC. These comments were gradually introduced with the commits below. ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK API") 38f790a80560 ("net: dsa: mt7530: Add support for port 5") 88bdef8be9f6 ("net: dsa: mt7530: Extend device data ready for adding a new hardware") c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch") Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Acked-by: Daniel Golle <daniel@makrotopia.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> --- drivers/net/dsa/mt7530.c | 32 ++++++++++++++++++++++---------- 1 file changed, 22 insertions(+), 10 deletions(-)