diff mbox series

[net-next,RFC,11/14] dt-bindings: net: add QCA807x PHY defines

Message ID 20231120135041.15259-12-ansuelsmth@gmail.com (mailing list archive)
State New, archived
Headers show
Series net: phy: Support DT PHY package | expand

Commit Message

Christian Marangi Nov. 20, 2023, 1:50 p.m. UTC
From: Robert Marko <robert.marko@sartura.hr>

Add DT bindings defined for Qualcomm QCA807x PHY series related to
calibration and DAC settings.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 include/dt-bindings/net/qcom-qca807x.h | 45 ++++++++++++++++++++++++++
 1 file changed, 45 insertions(+)
 create mode 100644 include/dt-bindings/net/qcom-qca807x.h

Comments

Andrew Lunn Nov. 23, 2023, 3:01 a.m. UTC | #1
On Mon, Nov 20, 2023 at 02:50:38PM +0100, Christian Marangi wrote:
> From: Robert Marko <robert.marko@sartura.hr>
> 
> Add DT bindings defined for Qualcomm QCA807x PHY series related to
> calibration and DAC settings.
> 
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  include/dt-bindings/net/qcom-qca807x.h | 45 ++++++++++++++++++++++++++
>  1 file changed, 45 insertions(+)
>  create mode 100644 include/dt-bindings/net/qcom-qca807x.h
> 
> diff --git a/include/dt-bindings/net/qcom-qca807x.h b/include/dt-bindings/net/qcom-qca807x.h
> new file mode 100644
> index 000000000000..42c45c7d5210
> --- /dev/null
> +++ b/include/dt-bindings/net/qcom-qca807x.h
> @@ -0,0 +1,45 @@
> +/* SPDX-License-Identifier: GPL-2.0-only OR MIT */
> +/*
> + * Device Tree constants for the Qualcomm QCA807X PHYs
> + */
> +
> +#ifndef _DT_BINDINGS_QCOM_QCA807X_H
> +#define _DT_BINDINGS_QCOM_QCA807X_H
> +
> +#define PSGMII_QSGMII_TX_DRIVER_140MV	0
> +#define PSGMII_QSGMII_TX_DRIVER_160MV	1
> +#define PSGMII_QSGMII_TX_DRIVER_180MV	2
> +#define PSGMII_QSGMII_TX_DRIVER_200MV	3
> +#define PSGMII_QSGMII_TX_DRIVER_220MV	4
> +#define PSGMII_QSGMII_TX_DRIVER_240MV	5
> +#define PSGMII_QSGMII_TX_DRIVER_260MV	6
> +#define PSGMII_QSGMII_TX_DRIVER_280MV	7
> +#define PSGMII_QSGMII_TX_DRIVER_300MV	8
> +#define PSGMII_QSGMII_TX_DRIVER_320MV	9
> +#define PSGMII_QSGMII_TX_DRIVER_400MV	10
> +#define PSGMII_QSGMII_TX_DRIVER_500MV	11
> +/* Default value */
> +#define PSGMII_QSGMII_TX_DRIVER_600MV	12

Its not clear what these are used for. I think these are actually
package properties, so having the correctly documented in the binding
would help a lot understand why we need package properties.

Actually using #define like this is probably wrong. You should just
have a u32 tx_driver_mv property, and list [140, 160, 180, 200,
... 600] as valid values. The driver should then convert to whatever
value it should write into the register.

      Andrew
diff mbox series

Patch

diff --git a/include/dt-bindings/net/qcom-qca807x.h b/include/dt-bindings/net/qcom-qca807x.h
new file mode 100644
index 000000000000..42c45c7d5210
--- /dev/null
+++ b/include/dt-bindings/net/qcom-qca807x.h
@@ -0,0 +1,45 @@ 
+/* SPDX-License-Identifier: GPL-2.0-only OR MIT */
+/*
+ * Device Tree constants for the Qualcomm QCA807X PHYs
+ */
+
+#ifndef _DT_BINDINGS_QCOM_QCA807X_H
+#define _DT_BINDINGS_QCOM_QCA807X_H
+
+#define PSGMII_QSGMII_TX_DRIVER_140MV	0
+#define PSGMII_QSGMII_TX_DRIVER_160MV	1
+#define PSGMII_QSGMII_TX_DRIVER_180MV	2
+#define PSGMII_QSGMII_TX_DRIVER_200MV	3
+#define PSGMII_QSGMII_TX_DRIVER_220MV	4
+#define PSGMII_QSGMII_TX_DRIVER_240MV	5
+#define PSGMII_QSGMII_TX_DRIVER_260MV	6
+#define PSGMII_QSGMII_TX_DRIVER_280MV	7
+#define PSGMII_QSGMII_TX_DRIVER_300MV	8
+#define PSGMII_QSGMII_TX_DRIVER_320MV	9
+#define PSGMII_QSGMII_TX_DRIVER_400MV	10
+#define PSGMII_QSGMII_TX_DRIVER_500MV	11
+/* Default value */
+#define PSGMII_QSGMII_TX_DRIVER_600MV	12
+
+/* Full amplitude, full bias current */
+#define QCA807X_CONTROL_DAC_FULL_VOLT_BIAS		0
+/* Amplitude follow DSP (amplitude is adjusted based on cable length), half bias current */
+#define QCA807X_CONTROL_DAC_DSP_VOLT_HALF_BIAS		1
+/* Full amplitude, bias current follow DSP (bias current is adjusted based on cable length) */
+#define QCA807X_CONTROL_DAC_FULL_VOLT_DSP_BIAS		2
+/* Both amplitude and bias current follow DSP */
+#define QCA807X_CONTROL_DAC_DSP_VOLT_BIAS		3
+/* Full amplitude, half bias current */
+#define QCA807X_CONTROL_DAC_FULL_VOLT_HALF_BIAS		4
+/* Amplitude follow DSP setting; 1/4 bias current when cable<10m,
+ * otherwise half bias current
+ */
+#define QCA807X_CONTROL_DAC_DSP_VOLT_QUARTER_BIAS	5
+/* Full amplitude; same bias current setting with “010” and “011”,
+ * but half more bias is reduced when cable <10m
+ */
+#define QCA807X_CONTROL_DAC_FULL_VOLT_HALF_BIAS_SHORT	6
+/* Amplitude follow DSP; same bias current setting with “110”, default value */
+#define QCA807X_CONTROL_DAC_DSP_VOLT_HALF_BIAS_SHORT	7
+
+#endif