| Message ID | 20231128055230.342547-6-n-francis@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add TPS6594 PMIC support on several boards | expand |
Hi Neha, On 11:22-20231128, Neha Malcom Francis wrote: > This patch adds support for TPS6594 PMIC on wkup I2C0 bus. This device > provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog, > an ESM (Error Signal Monitor) which monitors the SoC error output > signal, and a PFSM (Pre-configurable Finite State Machine) which manages > the operational modes of the PMIC. > > Signed-off-by: Neha Malcom Francis <n-francis@ti.com> > --- > arch/arm64/boot/dts/ti/k3-am69-sk.dts | 100 ++++++++++++++++++++++++++ > 1 file changed, 100 insertions(+) > > diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts > index 9868c7049bfb..dec27acb4e96 100644 > --- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts > +++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts > @@ -431,6 +431,17 @@ J784S4_IOPAD(0x000, PIN_INPUT, 7) /* (AN35) EXTINTN.GPIO0_0 */ > }; > }; > > +&wkup_pmx1 { > + status = "okay"; > + > + pmic_irq_pins_default: pmic-irq-default-pins { > + pinctrl-single,pins = < > + /* (AA37) MCU_ADC1_AIN4.WKUP_GPIO0_83 */ > + J784S4_WKUP_IOPAD(0x12c, PIN_INPUT, 7) > + >; > + }; > +}; > + > &wkup_pmx2 { > bootph-all; > wkup_uart0_pins_default: wkup-uart0-default-pins { > @@ -631,6 +642,95 @@ eeprom@51 { > compatible = "atmel,24c512"; > reg = <0x51>; > }; > + > + tps659413: pmic@48 { > + compatible = "ti,tps6594-q1"; > + reg = <0x48>; > + system-power-controller; > + pinctrl-names = "default"; > + pinctrl-0 = <&pmic_irq_pins_default>; > + interrupt-parent = <&wkup_gpio0>; > + interrupts = <39 IRQ_TYPE_EDGE_FALLING>; > + ti,primary-pmic; > + > + gpio-controller; > + #gpio-cells = <2>; > + > + buck12-supply = <&vsys_3v3>; > + buck3-supply = <&vsys_3v3>; > + buck4-supply = <&vsys_3v3>; > + buck5-supply = <&vsys_3v3>; > + ldo1-supply = <&vsys_3v3>; > + ldo2-supply = <&vsys_3v3>; > + ldo3-supply = <&vsys_3v3>; > + ldo4-supply = <&vsys_3v3>; > + > + regulators { > + bucka12: buck12 { > + regulator-name = "vdd_ddr_1v1"; > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1100000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + bucka3: buck3 { > + regulator-name = "vdd_ram_0v85"; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <850000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + bucka4: buck4 { > + regulator-name = "vdd_io_1v8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + bucka5: buck5 { > + regulator-name = "vdd_mcu_0v85"; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <850000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + ldoa1: ldo1 { > + regulator-name = "vdd_mcuio_1v8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + ldoa2: ldo2 { > + regulator-name = "vdd_mcuio_3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + ldoa3: ldo3 { > + regulator-name = "vds_dll_0v8"; > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <800000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + ldoa4: ldo4 { > + regulator-name = "vda_mcu_1v8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + }; > + }; > }; > With the full series applied: https://gist.github.com/manorit2001/7e794a7cbf58af4d7fbbee03eac88e86 [ For AM69-SK ] Tested-by: Manorit Chawdhry <m-chawdhry@ti.com> Regards, Manorit > &wkup_gpio0 { > -- > 2.34.1 >
Hi Manorit On 01-Dec-23 3:56 PM, Manorit Chawdhry wrote: > Hi Neha, > > On 11:22-20231128, Neha Malcom Francis wrote: >> This patch adds support for TPS6594 PMIC on wkup I2C0 bus. This device >> provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog, >> an ESM (Error Signal Monitor) which monitors the SoC error output >> signal, and a PFSM (Pre-configurable Finite State Machine) which manages >> the operational modes of the PMIC. >> >> Signed-off-by: Neha Malcom Francis <n-francis@ti.com> >> --- >> arch/arm64/boot/dts/ti/k3-am69-sk.dts | 100 ++++++++++++++++++++++++++ >> 1 file changed, 100 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts >> index 9868c7049bfb..dec27acb4e96 100644 >> --- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts >> +++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts >> @@ -431,6 +431,17 @@ J784S4_IOPAD(0x000, PIN_INPUT, 7) /* (AN35) EXTINTN.GPIO0_0 */ >> }; >> }; >> >> +&wkup_pmx1 { >> + status = "okay"; >> + >> + pmic_irq_pins_default: pmic-irq-default-pins { >> + pinctrl-single,pins = < >> + /* (AA37) MCU_ADC1_AIN4.WKUP_GPIO0_83 */ >> + J784S4_WKUP_IOPAD(0x12c, PIN_INPUT, 7) >> + >; >> + }; >> +}; >> + >> &wkup_pmx2 { >> bootph-all; >> wkup_uart0_pins_default: wkup-uart0-default-pins { >> @@ -631,6 +642,95 @@ eeprom@51 { >> compatible = "atmel,24c512"; >> reg = <0x51>; >> }; >> + >> + tps659413: pmic@48 { >> + compatible = "ti,tps6594-q1"; >> + reg = <0x48>; >> + system-power-controller; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pmic_irq_pins_default>; >> + interrupt-parent = <&wkup_gpio0>; >> + interrupts = <39 IRQ_TYPE_EDGE_FALLING>; >> + ti,primary-pmic; >> + >> + gpio-controller; >> + #gpio-cells = <2>; >> + >> + buck12-supply = <&vsys_3v3>; >> + buck3-supply = <&vsys_3v3>; >> + buck4-supply = <&vsys_3v3>; >> + buck5-supply = <&vsys_3v3>; >> + ldo1-supply = <&vsys_3v3>; >> + ldo2-supply = <&vsys_3v3>; >> + ldo3-supply = <&vsys_3v3>; >> + ldo4-supply = <&vsys_3v3>; >> + >> + regulators { >> + bucka12: buck12 { >> + regulator-name = "vdd_ddr_1v1"; >> + regulator-min-microvolt = <1100000>; >> + regulator-max-microvolt = <1100000>; >> + regulator-boot-on; >> + regulator-always-on; >> + }; >> + >> + bucka3: buck3 { >> + regulator-name = "vdd_ram_0v85"; >> + regulator-min-microvolt = <850000>; >> + regulator-max-microvolt = <850000>; >> + regulator-boot-on; >> + regulator-always-on; >> + }; >> + >> + bucka4: buck4 { >> + regulator-name = "vdd_io_1v8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-boot-on; >> + regulator-always-on; >> + }; >> + >> + bucka5: buck5 { >> + regulator-name = "vdd_mcu_0v85"; >> + regulator-min-microvolt = <850000>; >> + regulator-max-microvolt = <850000>; >> + regulator-boot-on; >> + regulator-always-on; >> + }; >> + >> + ldoa1: ldo1 { >> + regulator-name = "vdd_mcuio_1v8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-boot-on; >> + regulator-always-on; >> + }; >> + >> + ldoa2: ldo2 { >> + regulator-name = "vdd_mcuio_3v3"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-boot-on; >> + regulator-always-on; >> + }; >> + >> + ldoa3: ldo3 { >> + regulator-name = "vds_dll_0v8"; >> + regulator-min-microvolt = <800000>; >> + regulator-max-microvolt = <800000>; >> + regulator-boot-on; >> + regulator-always-on; >> + }; >> + >> + ldoa4: ldo4 { >> + regulator-name = "vda_mcu_1v8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-boot-on; >> + regulator-always-on; >> + }; >> + }; >> + }; >> }; >> > > With the full series applied: > https://gist.github.com/manorit2001/7e794a7cbf58af4d7fbbee03eac88e86 > > [ For AM69-SK ] > Tested-by: Manorit Chawdhry <m-chawdhry@ti.com> > > Regards, > Manorit > >> &wkup_gpio0 { >> -- >> 2.34.1 >> Thanks for testing!
diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts index 9868c7049bfb..dec27acb4e96 100644 --- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts +++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts @@ -431,6 +431,17 @@ J784S4_IOPAD(0x000, PIN_INPUT, 7) /* (AN35) EXTINTN.GPIO0_0 */ }; }; +&wkup_pmx1 { + status = "okay"; + + pmic_irq_pins_default: pmic-irq-default-pins { + pinctrl-single,pins = < + /* (AA37) MCU_ADC1_AIN4.WKUP_GPIO0_83 */ + J784S4_WKUP_IOPAD(0x12c, PIN_INPUT, 7) + >; + }; +}; + &wkup_pmx2 { bootph-all; wkup_uart0_pins_default: wkup-uart0-default-pins { @@ -631,6 +642,95 @@ eeprom@51 { compatible = "atmel,24c512"; reg = <0x51>; }; + + tps659413: pmic@48 { + compatible = "ti,tps6594-q1"; + reg = <0x48>; + system-power-controller; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_irq_pins_default>; + interrupt-parent = <&wkup_gpio0>; + interrupts = <39 IRQ_TYPE_EDGE_FALLING>; + ti,primary-pmic; + + gpio-controller; + #gpio-cells = <2>; + + buck12-supply = <&vsys_3v3>; + buck3-supply = <&vsys_3v3>; + buck4-supply = <&vsys_3v3>; + buck5-supply = <&vsys_3v3>; + ldo1-supply = <&vsys_3v3>; + ldo2-supply = <&vsys_3v3>; + ldo3-supply = <&vsys_3v3>; + ldo4-supply = <&vsys_3v3>; + + regulators { + bucka12: buck12 { + regulator-name = "vdd_ddr_1v1"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-boot-on; + regulator-always-on; + }; + + bucka3: buck3 { + regulator-name = "vdd_ram_0v85"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <850000>; + regulator-boot-on; + regulator-always-on; + }; + + bucka4: buck4 { + regulator-name = "vdd_io_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + bucka5: buck5 { + regulator-name = "vdd_mcu_0v85"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <850000>; + regulator-boot-on; + regulator-always-on; + }; + + ldoa1: ldo1 { + regulator-name = "vdd_mcuio_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldoa2: ldo2 { + regulator-name = "vdd_mcuio_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldoa3: ldo3 { + regulator-name = "vds_dll_0v8"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldoa4: ldo4 { + regulator-name = "vda_mcu_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; }; &wkup_gpio0 {
This patch adds support for TPS6594 PMIC on wkup I2C0 bus. This device provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor) which monitors the SoC error output signal, and a PFSM (Pre-configurable Finite State Machine) which manages the operational modes of the PMIC. Signed-off-by: Neha Malcom Francis <n-francis@ti.com> --- arch/arm64/boot/dts/ti/k3-am69-sk.dts | 100 ++++++++++++++++++++++++++ 1 file changed, 100 insertions(+)