diff mbox series

[v2,3/3] arm64: dts: allwinner: h618: add Transpeed 8K618-T TV box

Message ID 20231214015312.17363-4-andre.przywara@arm.com (mailing list archive)
State New, archived
Headers show
Series arm64: dts: allwinner: Add Transpeed 8K618-T TV box | expand

Commit Message

Andre Przywara Dec. 14, 2023, 1:53 a.m. UTC 
This is a Chinese TV box, probably very similar if not identical to
various other cheap TV boxes with the same specs:
      - Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache)
      - 2 or 4GiB DDR3L DRAM
      - 32, 64, or 128 GiB eMMC flash
      - AXP313a PMIC
      - 100 Mbit/s Ethernet (using yet unsupported internal PHY)
      - HDMI port
      - 2 * USB 2.0 ports
      - microSD card slot
      - 3.5mm A/V port
      - 7-segment display
      - 5V barrel plug power supply

The PCB provides holes for soldering a UART header or cable, this is
connected to the debug UART0. UART1 is used for the Bluetooth chip,
although this isn't working yet.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../sun50i-h618-transpeed-8k618-t.dts         | 161 ++++++++++++++++++
 2 files changed, 162 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-transpeed-8k618-t.dts

Comments

Jernej Škrabec Dec. 14, 2023, 4:28 p.m. UTC | #1 
On Thursday, December 14, 2023 2:53:12 AM CET Andre Przywara wrote:
> This is a Chinese TV box, probably very similar if not identical to
> various other cheap TV boxes with the same specs:
>       - Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache)
>       - 2 or 4GiB DDR3L DRAM
>       - 32, 64, or 128 GiB eMMC flash
>       - AXP313a PMIC
>       - 100 Mbit/s Ethernet (using yet unsupported internal PHY)
>       - HDMI port
>       - 2 * USB 2.0 ports
>       - microSD card slot
>       - 3.5mm A/V port
>       - 7-segment display
>       - 5V barrel plug power supply
> 
> The PCB provides holes for soldering a UART header or cable, this is
> connected to the debug UART0. UART1 is used for the Bluetooth chip,
> although this isn't working yet.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>

Best regards,
Jernej
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 3aca6787a1679..91d505b385de5 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -43,3 +43,4 @@  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-pi.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h618-transpeed-8k618-t.dts b/arch/arm64/boot/dts/allwinner/sun50i-h618-transpeed-8k618-t.dts
new file mode 100644
index 0000000000000..8ea1fd41aebaa
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h618-transpeed-8k618-t.dts
@@ -0,0 +1,161 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2023 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	model = "Transpeed 8K618-T";
+	compatible = "transpeed,8k618-t", "allwinner,sun50i-h618";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the DC input */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		/* discrete 3.3V regulator */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ir {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dldo1>;
+	cd-gpios = <&pio 8 16 GPIO_ACTIVE_LOW>;	/* PI16 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc2 {
+	vmmc-supply = <&reg_dldo1>;
+	vqmmc-supply = <&reg_aldo1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&r_i2c {
+	status = "okay";
+
+	axp313: pmic@36 {
+		compatible = "x-powers,axp313a";
+		reg = <0x36>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+
+		vin1-supply = <&reg_vcc5v>;
+		vin2-supply = <&reg_vcc5v>;
+		vin3-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-1v8-pll";
+			};
+
+			reg_dldo1: dldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-3v3-io-mmc";
+			};
+
+			reg_dcdc1: dcdc1 {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <990000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdc2: dcdc2 {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt = <1360000>;
+				regulator-max-microvolt = <1360000>;
+				regulator-name = "vdd-dram";
+			};
+		};
+	};
+};
+
+&pio {
+	vcc-pc-supply = <&reg_aldo1>;
+	vcc-pg-supply = <&reg_dldo1>;
+	vcc-ph-supply = <&reg_dldo1>;
+	vcc-pi-supply = <&reg_dldo1>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbotg {
+	dr_mode = "host";	/* USB A type receptable */
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};