diff mbox series

[3/3] ARM: dts: imx6dl: Add support for Sielaff i.MX6 Solo board

Message ID 20240116105317.267525-4-frieder@fris.de (mailing list archive)
State New, archived
Headers show
Series ARM: dts: imx6dl: Add support for Sielaff i.MX6 Solo board | expand

Commit Message

Frieder Schrempf Jan. 16, 2024, 10:51 a.m. UTC
From: Frieder Schrempf <frieder.schrempf@kontron.de>

The Sielaff i.MX6 Solo board is used as controller and user interface
in vending machines. It is based on the i.MX6 Solo SoC and features
the following peripherals and interfaces:

* 512 MB DDR3 RAM
* 512 MB NAND Flash
* 1 MB NOR Flash
* SD card
* Debug LED
* Debug UART
* Key Inputs
* RTC
* RS232
* 100 MBit Ethernet
* USB Hub
* USB OTG
* HDMI
* 7" LVDS IPS panel
* PWM Backlight
* Optional Extension Board with USB Ethernet NIC

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm/boot/dts/nxp/imx/Makefile           |   1 +
 arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts | 533 +++++++++++++++++++
 2 files changed, 534 insertions(+)
 create mode 100644 arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts

Comments

Fabio Estevam Jan. 16, 2024, 11:21 a.m. UTC | #1
On Tue, Jan 16, 2024 at 7:54 AM Frieder Schrempf <frieder@fris.de> wrote:

> +&i2c3 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_i2c3>;
> +       clock-frequency = <100000>;
> +       status = "okay";
> +
> +       st1633@55 {

Please use a generic node name.

> +       gt911@5d {

Ditto.
Frieder Schrempf Jan. 16, 2024, 11:36 a.m. UTC | #2
Hi Fabio,

On 16.01.24 12:21, Fabio Estevam wrote:
> On Tue, Jan 16, 2024 at 7:54 AM Frieder Schrempf <frieder@fris.de> wrote:
> 
>> +&i2c3 {
>> +       pinctrl-names = "default";
>> +       pinctrl-0 = <&pinctrl_i2c3>;
>> +       clock-frequency = <100000>;
>> +       status = "okay";
>> +
>> +       st1633@55 {
> 
> Please use a generic node name.
> 
>> +       gt911@5d {
> 
> Ditto.

Ok, I'll change the node names to touchscreen@55 and touchscreen@5d.

Thanks
Frieder
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
index a724d1a7a9a07..c32e004e7610c 100644
--- a/arch/arm/boot/dts/nxp/imx/Makefile
+++ b/arch/arm/boot/dts/nxp/imx/Makefile
@@ -118,6 +118,7 @@  dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-sabrelite.dtb \
 	imx6dl-sabresd.dtb \
 	imx6dl-savageboard.dtb \
+	imx6dl-sielaff.dtb \
 	imx6dl-skov-revc-lt2.dtb \
 	imx6dl-skov-revc-lt6.dtb \
 	imx6dl-solidsense.dtb \
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts
new file mode 100644
index 0000000000000..9340fbcdd0265
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts
@@ -0,0 +1,533 @@ 
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2022 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Sielaff i.MX6 Solo";
+	compatible = "sielaff,imx6dl-board", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	backlight: pwm-backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		pwms = <&pwm3 0 50000 0>;
+		brightness-levels = <0 0 64 88 112 136 184 232 255>;
+		default-brightness-level = <4>;
+		enable-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_backlight>;
+	};
+
+	cec {
+		compatible = "cec-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hdmi_cec>;
+		cec-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
+		hdmi-phandle = <&hdmi>;
+	};
+
+	enet_ref: clock-enet-ref {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet-ref";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-0 {
+			gpios = <&gpio2 16 0>;
+			debounce-interval = <10>;
+			linux,code = <1>;
+		};
+
+		key-1 {
+			gpios = <&gpio3 27 0>;
+			debounce-interval = <10>;
+			linux,code = <2>;
+		};
+
+		key-2 {
+			gpios = <&gpio5 4 0>;
+			debounce-interval = <10>;
+			linux,code = <3>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led-debug {
+			label = "debug-led";
+			gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+		device_type = "memory";
+	};
+
+	osc_eth_phy: clock-osc-eth-phy {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+		clock-output-names = "osc-eth-phy";
+	};
+
+	panel {
+		compatible = "lg,lb070wv8";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in_lvds: endpoint {
+				remote-endpoint = <&lvds_out>;
+			};
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_backlight: regulator-backlight {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_backlight>;
+		enable-active-high;
+		gpio = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+		regulator-name = "backlight";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usbotg_vbus>;
+		enable-active-high;
+		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&fec {
+	/*
+	 * Set PTP clock to external instead of internal reference, as the
+	 * REF_CLK from the PHY is fed back into the i.MX6 and the GPR
+	 * register needs to be set accordingly (see mach-imx6q.c).
+	 */
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		 <&clks IMX6QDL_CLK_ENET>,
+		 <&enet_ref>,
+		 <&clks IMX6QDL_CLK_ENET_REF>;
+	clock-names = "ipg", "ahb", "ptp", "enet_out";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-connection-type = "rmii";
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@1 {
+			reg = <1>;
+			clocks = <&osc_eth_phy>;
+			clock-names = "rmii-ref";
+			micrel,led-mode = <1>;
+			reset-assert-us = <500>;
+			reset-deassert-us = <100>;
+			reset-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "key-out", "key-in",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"lan9500a-rst", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c4>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	st1633@55 {
+		compatible = "sitronix,st1633";
+		reg = <0x55>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpio5>;
+		gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+	};
+
+	gt911@5d {
+		compatible = "goodix,gt928";
+		reg = <0x5d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio5>;
+		irq-gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&ldb {
+	status = "okay";
+
+	lvds: lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds_out: endpoint {
+				remote-endpoint = <&panel_in_lvds>;
+			};
+		};
+	};
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	disable-over-current;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	usb1@1 {
+		compatible = "usb4b4,6570";
+		reg = <1>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+
+		assigned-clocks = <&clks IMX6QDL_CLK_CKO>,
+				  <&clks IMX6QDL_CLK_CKO2_SEL>;
+		assigned-clock-parents = <&clks IMX6QDL_CLK_CKO2>,
+					 <&clks IMX6QDL_CLK_OSC>;
+		assigned-clock-rates = <12000000 0>;
+	};
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	dr_mode = "host";
+	over-current-active-low;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_3v3>;
+	voltage-ranges = <3300 3300>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RD0__GPIO6_IO25	0x1b0b0	/* PMIC_IRQ */
+			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12		0x1b0b0
+			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14		0x1b0b0
+			MX6QDL_PAD_SD2_DAT0__GPIO1_IO15		0x1b0b0
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08		0x1b0b0
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x1b0b0
+		>;
+	};
+
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x100b1
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO	0x100b1
+			MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI	0x100b1
+			MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK	0x100b1
+			MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29	0x100b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x100b1
+		>;
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A22__GPIO2_IO16		0x1b080
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27		0x1b080
+			MX6QDL_PAD_EIM_A24__GPIO5_IO04		0x1b080
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x1b0b0
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
+		>;
+	};
+
+	pinctrl_hdmi_cec: hdmicecgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A21__GPIO2_IO17		0x1b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001f8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__I2C4_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_8__I2C4_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_reg_backlight: regbacklightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23	0x1b0b1
+		>;
+	};
+
+	pinctrl_reg_usbotg_vbus: regusbotgvbusgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b1
+		>;
+	};
+
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18	0x1b0b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 	0x1b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b0
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b0
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__USB_H1_OC		0x1b0b1
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1		0x1b0b0
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__USB_OTG_OC		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x100b1
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__WDOG1_B		0x1b0b0
+		>;
+	};
+};