diff mbox series

[v3,12/17] spi: s3c64xx: return ETIMEDOUT for wait_for_completion_timeout()

Message ID 20240126171546.1233172-13-tudor.ambarus@linaro.org (mailing list archive)
State New, archived
Headers show
Series spi: s3c64xx: straightforward cleanup | expand

Commit Message

Tudor Ambarus Jan. 26, 2024, 5:15 p.m. UTC
ETIMEDOUT is more specific than EIO, use it for
wait_for_completion_timeout().

Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
---
 drivers/spi/spi-s3c64xx.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

Comments

Sam Protsenko Jan. 26, 2024, 8:13 p.m. UTC | #1
On Fri, Jan 26, 2024 at 11:16 AM Tudor Ambarus <tudor.ambarus@linaro.org> wrote:
>
> ETIMEDOUT is more specific than EIO, use it for
> wait_for_completion_timeout().
>
> Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
> ---

Looks like you missed my R-b tag I added to this patch in your
previous submission.

>  drivers/spi/spi-s3c64xx.c | 6 +++---
>  1 file changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c
> index 76fa378ab5ab..2f2c4ad35df4 100644
> --- a/drivers/spi/spi-s3c64xx.c
> +++ b/drivers/spi/spi-s3c64xx.c
> @@ -526,7 +526,7 @@ static int s3c64xx_wait_for_dma(struct s3c64xx_spi_driver_data *sdd,
>
>         /*
>          * If the previous xfer was completed within timeout, then
> -        * proceed further else return -EIO.
> +        * proceed further else return -ETIMEDOUT.
>          * DmaTx returns after simply writing data in the FIFO,
>          * w/o waiting for real transmission on the bus to finish.
>          * DmaRx returns only after Dma read data from FIFO which
> @@ -547,7 +547,7 @@ static int s3c64xx_wait_for_dma(struct s3c64xx_spi_driver_data *sdd,
>
>         /* If timed out while checking rx/tx status return error */
>         if (!val)
> -               return -EIO;
> +               return -ETIMEDOUT;
>
>         return 0;
>  }
> @@ -577,7 +577,7 @@ static int s3c64xx_wait_for_pio(struct s3c64xx_spi_driver_data *sdd,
>         if (use_irq) {
>                 val = msecs_to_jiffies(ms);
>                 if (!wait_for_completion_timeout(&sdd->xfer_completion, val))
> -                       return -EIO;
> +                       return -ETIMEDOUT;
>         }
>
>         val = msecs_to_loops(ms);
> --
> 2.43.0.429.g432eaa2c6b-goog
>
Tudor Ambarus Jan. 27, 2024, 3:26 a.m. UTC | #2
On 1/26/24 20:13, Sam Protsenko wrote:
>> ETIMEDOUT is more specific than EIO, use it for
>> wait_for_completion_timeout().
>>
>> Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
>> ---
> Looks like you missed my R-b tag I added to this patch in your
> previous submission.

My apologies. Adding it here should do the trick, here it is:

Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
diff mbox series

Patch

diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c
index 76fa378ab5ab..2f2c4ad35df4 100644
--- a/drivers/spi/spi-s3c64xx.c
+++ b/drivers/spi/spi-s3c64xx.c
@@ -526,7 +526,7 @@  static int s3c64xx_wait_for_dma(struct s3c64xx_spi_driver_data *sdd,
 
 	/*
 	 * If the previous xfer was completed within timeout, then
-	 * proceed further else return -EIO.
+	 * proceed further else return -ETIMEDOUT.
 	 * DmaTx returns after simply writing data in the FIFO,
 	 * w/o waiting for real transmission on the bus to finish.
 	 * DmaRx returns only after Dma read data from FIFO which
@@ -547,7 +547,7 @@  static int s3c64xx_wait_for_dma(struct s3c64xx_spi_driver_data *sdd,
 
 	/* If timed out while checking rx/tx status return error */
 	if (!val)
-		return -EIO;
+		return -ETIMEDOUT;
 
 	return 0;
 }
@@ -577,7 +577,7 @@  static int s3c64xx_wait_for_pio(struct s3c64xx_spi_driver_data *sdd,
 	if (use_irq) {
 		val = msecs_to_jiffies(ms);
 		if (!wait_for_completion_timeout(&sdd->xfer_completion, val))
-			return -EIO;
+			return -ETIMEDOUT;
 	}
 
 	val = msecs_to_loops(ms);