[3/3] arm64: dts: allwinner: Add Jide Remix Mini PC support

Message ID	20240204094404.149776-4-andre.przywara@arm.com (mailing list archive)
State	New, archived
Headers	show Return-Path: <linux-arm-kernel-bounces+linux-arm-kernel=archiver.kernel.org@lists.infradead.org> From: Andre Przywara <andre.przywara@arm.com> To: Jernej Skrabec <jernej.skrabec@gmail.com>, Chen-Yu Tsai <wens@csie.org>, Samuel Holland <samuel@sholland.org>, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Conor Dooley <conor+dt@kernel.org> Cc: linux-sunxi@lists.linux.dev, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, Nick Alilovic <nickalilovic@gmail.com> Subject: [PATCH 3/3] arm64: dts: allwinner: Add Jide Remix Mini PC support Date: Sun, 4 Feb 2024 10:44:04 +0100 Message-Id: <20240204094404.149776-4-andre.przywara@arm.com> In-Reply-To: <20240204094404.149776-1-andre.przywara@arm.com> References: <20240204094404.149776-1-andre.przywara@arm.com> MIME-Version: 1.0 Precedence: list Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Sender: "linux-arm-kernel" <linux-arm-kernel-bounces@lists.infradead.org> Errors-To: linux-arm-kernel-bounces+linux-arm-kernel=archiver.kernel.org@lists.infradead.org
Series	arm64: dts: allwinner: Add Remix Mini PC support \| expand [0/3] arm64: dts: allwinner: Add Remix Mini PC support [1/3] dt-bindings: vendor-prefixes: add Jide [2/3] dt-bindings: arm: sunxi: document Remix Mini PC name [3/3] arm64: dts: allwinner: Add Jide Remix Mini PC support

Andre Przywara Feb. 4, 2024, 9:44 a.m. UTC

The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
which appears to be just a relabelled A64. It was launched in 2015 by
the now defunct company Jide, and shipped with a desktop optimised
version of Android. It features
	- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
	- 1 or 2 GB DRAM
	- 8 or 16 GB eMMC flash
	- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
	- RTL8723BS WiFi & Bluetooth chip
	- HDMI port
	- two USB 2.0 ports
	- 3.5mm AV port
	- microSD card slot

The devicetree covers most peripherals, though there is no agreed
binding for the PHY chip yet, so this is left out.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun50i-h64-remix-mini-pc.dts    | 357 ++++++++++++++++++
 2 files changed, 358 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts

Jernej Škrabec Feb. 5, 2024, 6:12 p.m. UTC | #1

Hi Andre!

Dne nedelja, 04. februar 2024 ob 10:44:04 CET je Andre Przywara napisal(a):
> The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
> which appears to be just a relabelled A64. It was launched in 2015 by
> the now defunct company Jide, and shipped with a desktop optimised
> version of Android. It features
> 	- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
> 	- 1 or 2 GB DRAM
> 	- 8 or 16 GB eMMC flash
> 	- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
> 	- RTL8723BS WiFi & Bluetooth chip
> 	- HDMI port
> 	- two USB 2.0 ports
> 	- 3.5mm AV port
> 	- microSD card slot
> 
> The devicetree covers most peripherals, though there is no agreed
> binding for the PHY chip yet, so this is left out.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
>  arch/arm64/boot/dts/allwinner/Makefile        |   1 +
>  .../allwinner/sun50i-h64-remix-mini-pc.dts    | 357 ++++++++++++++++++
>  2 files changed, 358 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> 
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index 91d505b385de..2db3b15ad09f 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab-early-adopter.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h64-remix-mini-pc.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> new file mode 100644
> index 000000000000..537923a541a8
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> @@ -0,0 +1,357 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +// Copyright (c) 2018 ARM Ltd.

Shouldn't be 2024?

> +
> +/dts-v1/;
> +
> +#include "sun50i-a64.dtsi"
> +#include "sun50i-a64-cpu-opp.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> +	model = "Remix Mini PC";
> +	compatible = "jide,remix-mini-pc", "allwinner,sun50i-h64",
> +		     "allwinner,sun50i-a64";
> +
> +	aliases {
> +		ethernet1 = &rtl8723bs;
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	hdmi-connector {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con_in: endpoint {
> +				remote-endpoint = <&hdmi_out_con>;
> +			};
> +		};
> +	};
> +
> +	reg_vcc5v: regulator-5v {
> +		/* board wide 5V supply directly from the DC input */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc-5v";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +
> +	wifi_pwrseq: wifi_pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		pinctrl-names = "default";
> +		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
> +		post-power-on-delay-ms = <200>;
> +	};
> +};
> +
> +&codec {
> +	status = "okay";
> +};
> +
> +&codec_analog {
> +	cpvdd-supply = <&reg_eldo1>;
> +	status = "okay";
> +};
> +
> +&cpu0 {
> +	cpu-supply = <&reg_dcdc2>;
> +};
> +
> +&cpu1 {
> +	cpu-supply = <&reg_dcdc2>;
> +};
> +
> +&cpu2 {
> +	cpu-supply = <&reg_dcdc2>;
> +};
> +
> +&cpu3 {
> +	cpu-supply = <&reg_dcdc2>;
> +};
> +
> +&dai {
> +	status = "okay";
> +};
> +
> +&de {
> +	status = "okay";
> +};
> +
> +&ehci0 {
> +	status = "okay";
> +};
> +
> +&ehci1 {
> +	status = "okay";
> +};
> +
> +&hdmi {
> +	hvcc-supply = <&reg_dldo1>;
> +	status = "okay";
> +};
> +
> +&hdmi_out {
> +	hdmi_out_con: endpoint {
> +		remote-endpoint = <&hdmi_con_in>;
> +	};
> +};
> +
> +/* Connects to the AC200 chip */
> +&i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c0_pins>;
> +	status = "okay";
> +};
> +
> +&i2c0_pins {
> +	bias-pull-up;
> +};
> +
> +&mmc0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc0_pins>;
> +	vmmc-supply = <&reg_dcdc1>;
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> +	disable-wp;
> +	bus-width = <4>;
> +	status = "okay";
> +};
> +
> +&mmc1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc1_pins>;
> +	vmmc-supply = <&reg_aldo1>;
> +	vqmmc-supply = <&reg_dldo4>;
> +	mmc-pwrseq = <&wifi_pwrseq>;
> +	bus-width = <4>;
> +	non-removable;
> +	status = "okay";
> +
> +	rtl8723bs: wifi@1 {
> +		reg = <1>;
> +		interrupt-parent = <&r_pio>;
> +		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
> +		interrupt-names = "host-wake";
> +	};

Node without compatible doesn't help. Please remove it.

> +};
> +
> +&mmc2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
> +	vmmc-supply = <&reg_dcdc1>;
> +	vqmmc-supply = <&reg_eldo1>;
> +	bus-width = <8>;
> +	non-removable;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;

Aren't these speed modes enabled by default?


Best regards,
Jernej

> +	cap-mmc-hw-reset;
> +	status = "okay";
> +};
> +
> +&ohci0 {
> +	status = "okay";
> +};
> +
> +&ohci1 {
> +	status = "okay";
> +};
> +
> +&pio {
> +	vcc-pb-supply = <&reg_dcdc1>;
> +	vcc-pc-supply = <&reg_dcdc1>;
> +	vcc-pd-supply = <&reg_dcdc1>;
> +	vcc-pe-supply = <&reg_dcdc1>;
> +	vcc-pf-supply = <&reg_dcdc1>;
> +	vcc-pg-supply = <&reg_dldo4>;
> +	vcc-ph-supply = <&reg_dcdc1>;
> +};
> +
> +&r_ir {
> +	status = "okay";
> +};
> +
> +&r_pio {
> +	/*
> +	 * We cannot add that supply for now since it would create a circular
> +	 * dependency between pinctrl, the regulator and the RSB Bus.
> +	 *
> +	 * vcc-pl-supply = <&reg_aldo2>;
> +	 */
> +};
> +
> +&r_rsb {
> +	status = "okay";
> +
> +	axp803: pmic@3a3 {
> +		compatible = "x-powers,axp803";
> +		reg = <0x3a3>;
> +		interrupt-parent = <&r_intc>;
> +		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_LOW>;
> +		x-powers,drive-vbus-en;
> +
> +		vin1-supply = <&reg_vcc5v>;
> +		vin2-supply = <&reg_vcc5v>;
> +		vin3-supply = <&reg_vcc5v>;
> +		vin5-supply = <&reg_vcc5v>;
> +		vin6-supply = <&reg_vcc5v>;
> +		aldoin-supply = <&reg_vcc5v>;
> +		dldoin-supply = <&reg_vcc5v>;
> +		eldoin-supply = <&reg_vcc5v>;
> +		fldoin-supply = <&reg_vcc5v>;
> +		drivevbus-supply = <&reg_vcc5v>;
> +		ips-supply = <&reg_vcc5v>;
> +
> +		status = "okay";
> +	};
> +};
> +
> +#include "axp803.dtsi"
> +
> +&ac_power_supply {
> +	status = "okay";
> +};
> +
> +&reg_dcdc1 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <3300000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "vcc-3v3";
> +};
> +
> +&reg_dcdc2 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1040000>;
> +	regulator-max-microvolt = <1300000>;
> +	regulator-name = "vdd-cpux";
> +};
> +
> +/* DCDC3 is polyphased with DCDC2 */
> +
> +&reg_dcdc5 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1500000>;
> +	regulator-max-microvolt = <1500000>;
> +	regulator-name = "vcc-dram";
> +};
> +
> +/* Deviates from the reset default of 1.1V. */
> +&reg_dcdc6 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1200000>;
> +	regulator-max-microvolt = <1200000>;
> +	regulator-name = "vdd-sys";
> +};
> +
> +&reg_aldo1 {
> +	regulator-min-microvolt = <3300000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "vcc-wifi";
> +};
> +
> +&reg_aldo2 {
> +	/* Specifying R_PIO consumer would create circular dependency. */
> +	regulator-always-on;
> +	regulator-min-microvolt = <3300000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "vcc-pl";
> +};
> +
> +&reg_aldo3 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <3000000>;
> +	regulator-max-microvolt = <3000000>;
> +	regulator-name = "vcc-pll-avcc";
> +};
> +
> +/* AC200 power supply */
> +&reg_dldo1 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <3300000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "vcc-ave-33";
> +};
> +
> +&reg_dldo4 {
> +	regulator-min-microvolt = <3300000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "vcc-wifi-io";
> +};
> +
> +&reg_drivevbus {
> +	regulator-name = "usb0-vbus";
> +	status = "okay";
> +};
> +
> +&reg_eldo1 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1800000>;
> +	regulator-max-microvolt = <1800000>;
> +	regulator-name = "vcc-cpvdd-dram-emmc";
> +};
> +
> +/* Supplies the arisc management core, needed by TF-A to power off cores. */
> +&reg_fldo2 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1100000>;
> +	regulator-max-microvolt = <1100000>;
> +	regulator-name = "vdd-cpus";
> +};
> +
> +&reg_rtc_ldo {
> +	regulator-name = "vcc-rtc";
> +};
> +
> +&simplefb_hdmi {
> +	vcc-hdmi-supply = <&reg_dcdc1>;
> +};
> +
> +&sound {
> +	simple-audio-card,aux-devs = <&codec_analog>;
> +	simple-audio-card,widgets = "Microphone", "Microphone Jack",
> +				    "Headphone", "Headphone Jack";
> +	simple-audio-card,routing =
> +			"Left DAC", "DACL",
> +			"Right DAC", "DACR",
> +			"Headphone Jack", "HP",
> +			"ADCL", "Left ADC",
> +			"ADCR", "Right ADC",
> +			"MIC2", "Microphone Jack";
> +	status = "okay";
> +};
> +
> +/* On the (unpopulated) UART pads. */
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_pb_pins>;
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> +	uart-has-rtscts;
> +	status = "okay";
> +
> +	bluetooth {
> +		compatible = "realtek,rtl8723bs-bt";
> +		enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> +		max-speed = <1500000>;
> +	};
> +};
> +
> +&usb_otg {
> +	dr_mode = "host";
> +	status = "okay";
> +};
> +
> +&usbphy {
> +	usb0_vbus-supply = <&reg_drivevbus>;
> +	usb1_vbus-supply = <&reg_drivevbus>;
> +	status = "okay";
> +};
>

Jernej Škrabec Feb. 5, 2024, 6:20 p.m. UTC | #2

Dne ponedeljek, 05. februar 2024 ob 19:12:45 CET je Jernej Škrabec napisal(a):
> Hi Andre!
> 
> Dne nedelja, 04. februar 2024 ob 10:44:04 CET je Andre Przywara napisal(a):
> > The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
> > which appears to be just a relabelled A64. It was launched in 2015 by
> > the now defunct company Jide, and shipped with a desktop optimised
> > version of Android. It features
> > 	- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
> > 	- 1 or 2 GB DRAM
> > 	- 8 or 16 GB eMMC flash
> > 	- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
> > 	- RTL8723BS WiFi & Bluetooth chip
> > 	- HDMI port
> > 	- two USB 2.0 ports
> > 	- 3.5mm AV port
> > 	- microSD card slot
> > 
> > The devicetree covers most peripherals, though there is no agreed
> > binding for the PHY chip yet, so this is left out.
> > 
> > Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> > ---
> >  arch/arm64/boot/dts/allwinner/Makefile        |   1 +
> >  .../allwinner/sun50i-h64-remix-mini-pc.dts    | 357 ++++++++++++++++++
> >  2 files changed, 358 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> > 
> > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> > index 91d505b385de..2db3b15ad09f 100644
> > --- a/arch/arm64/boot/dts/allwinner/Makefile
> > +++ b/arch/arm64/boot/dts/allwinner/Makefile
> > @@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
> >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab-early-adopter.dtb
> >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
> >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
> > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h64-remix-mini-pc.dtb
> >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb
> >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
> >  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> > new file mode 100644
> > index 000000000000..537923a541a8
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> > @@ -0,0 +1,357 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +// Copyright (c) 2018 ARM Ltd.
> 
> Shouldn't be 2024?
> 
> > +
> > +/dts-v1/;
> > +
> > +#include "sun50i-a64.dtsi"
> > +#include "sun50i-a64-cpu-opp.dtsi"
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +
> > +/ {
> > +	model = "Remix Mini PC";
> > +	compatible = "jide,remix-mini-pc", "allwinner,sun50i-h64",
> > +		     "allwinner,sun50i-a64";
> > +
> > +	aliases {
> > +		ethernet1 = &rtl8723bs;
> > +		serial0 = &uart0;
> > +	};
> > +
> > +	chosen {
> > +		stdout-path = "serial0:115200n8";
> > +	};
> > +
> > +	hdmi-connector {
> > +		compatible = "hdmi-connector";
> > +		type = "a";
> > +
> > +		port {
> > +			hdmi_con_in: endpoint {
> > +				remote-endpoint = <&hdmi_out_con>;
> > +			};
> > +		};
> > +	};
> > +
> > +	reg_vcc5v: regulator-5v {
> > +		/* board wide 5V supply directly from the DC input */
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "vcc-5v";
> > +		regulator-min-microvolt = <5000000>;
> > +		regulator-max-microvolt = <5000000>;
> > +		regulator-always-on;
> > +	};
> > +
> > +	wifi_pwrseq: wifi_pwrseq {
> > +		compatible = "mmc-pwrseq-simple";
> > +		pinctrl-names = "default";
> > +		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
> > +		post-power-on-delay-ms = <200>;
> > +	};
> > +};
> > +
> > +&codec {
> > +	status = "okay";
> > +};
> > +
> > +&codec_analog {
> > +	cpvdd-supply = <&reg_eldo1>;
> > +	status = "okay";
> > +};
> > +
> > +&cpu0 {
> > +	cpu-supply = <&reg_dcdc2>;
> > +};
> > +
> > +&cpu1 {
> > +	cpu-supply = <&reg_dcdc2>;
> > +};
> > +
> > +&cpu2 {
> > +	cpu-supply = <&reg_dcdc2>;
> > +};
> > +
> > +&cpu3 {
> > +	cpu-supply = <&reg_dcdc2>;
> > +};
> > +
> > +&dai {
> > +	status = "okay";
> > +};
> > +
> > +&de {
> > +	status = "okay";
> > +};
> > +
> > +&ehci0 {
> > +	status = "okay";
> > +};
> > +
> > +&ehci1 {
> > +	status = "okay";
> > +};
> > +
> > +&hdmi {
> > +	hvcc-supply = <&reg_dldo1>;
> > +	status = "okay";
> > +};
> > +
> > +&hdmi_out {
> > +	hdmi_out_con: endpoint {
> > +		remote-endpoint = <&hdmi_con_in>;
> > +	};
> > +};
> > +
> > +/* Connects to the AC200 chip */
> > +&i2c0 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&i2c0_pins>;
> > +	status = "okay";
> > +};
> > +
> > +&i2c0_pins {
> > +	bias-pull-up;
> > +};
> > +
> > +&mmc0 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&mmc0_pins>;
> > +	vmmc-supply = <&reg_dcdc1>;
> > +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> > +	disable-wp;
> > +	bus-width = <4>;
> > +	status = "okay";
> > +};
> > +
> > +&mmc1 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&mmc1_pins>;
> > +	vmmc-supply = <&reg_aldo1>;
> > +	vqmmc-supply = <&reg_dldo4>;
> > +	mmc-pwrseq = <&wifi_pwrseq>;
> > +	bus-width = <4>;
> > +	non-removable;
> > +	status = "okay";
> > +
> > +	rtl8723bs: wifi@1 {
> > +		reg = <1>;
> > +		interrupt-parent = <&r_pio>;
> > +		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
> > +		interrupt-names = "host-wake";
> > +	};
> 
> Node without compatible doesn't help. Please remove it.
> 
> > +};
> > +
> > +&mmc2 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
> > +	vmmc-supply = <&reg_dcdc1>;
> > +	vqmmc-supply = <&reg_eldo1>;
> > +	bus-width = <8>;
> > +	non-removable;
> > +	mmc-ddr-1_8v;
> > +	mmc-hs200-1_8v;
> 
> Aren't these speed modes enabled by default?

Sorry, mmc-hs200-1_8v is ok, but mmc-ddr-1_8v should be
removed.

Best regards,
Jernej

> > +	cap-mmc-hw-reset;
> > +	status = "okay";
> > +};
> > +
> > +&ohci0 {
> > +	status = "okay";
> > +};
> > +
> > +&ohci1 {
> > +	status = "okay";
> > +};
> > +
> > +&pio {
> > +	vcc-pb-supply = <&reg_dcdc1>;
> > +	vcc-pc-supply = <&reg_dcdc1>;
> > +	vcc-pd-supply = <&reg_dcdc1>;
> > +	vcc-pe-supply = <&reg_dcdc1>;
> > +	vcc-pf-supply = <&reg_dcdc1>;
> > +	vcc-pg-supply = <&reg_dldo4>;
> > +	vcc-ph-supply = <&reg_dcdc1>;
> > +};
> > +
> > +&r_ir {
> > +	status = "okay";
> > +};
> > +
> > +&r_pio {
> > +	/*
> > +	 * We cannot add that supply for now since it would create a circular
> > +	 * dependency between pinctrl, the regulator and the RSB Bus.
> > +	 *
> > +	 * vcc-pl-supply = <&reg_aldo2>;
> > +	 */
> > +};
> > +
> > +&r_rsb {
> > +	status = "okay";
> > +
> > +	axp803: pmic@3a3 {
> > +		compatible = "x-powers,axp803";
> > +		reg = <0x3a3>;
> > +		interrupt-parent = <&r_intc>;
> > +		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_LOW>;
> > +		x-powers,drive-vbus-en;
> > +
> > +		vin1-supply = <&reg_vcc5v>;
> > +		vin2-supply = <&reg_vcc5v>;
> > +		vin3-supply = <&reg_vcc5v>;
> > +		vin5-supply = <&reg_vcc5v>;
> > +		vin6-supply = <&reg_vcc5v>;
> > +		aldoin-supply = <&reg_vcc5v>;
> > +		dldoin-supply = <&reg_vcc5v>;
> > +		eldoin-supply = <&reg_vcc5v>;
> > +		fldoin-supply = <&reg_vcc5v>;
> > +		drivevbus-supply = <&reg_vcc5v>;
> > +		ips-supply = <&reg_vcc5v>;
> > +
> > +		status = "okay";
> > +	};
> > +};
> > +
> > +#include "axp803.dtsi"
> > +
> > +&ac_power_supply {
> > +	status = "okay";
> > +};
> > +
> > +&reg_dcdc1 {
> > +	regulator-always-on;
> > +	regulator-min-microvolt = <3300000>;
> > +	regulator-max-microvolt = <3300000>;
> > +	regulator-name = "vcc-3v3";
> > +};
> > +
> > +&reg_dcdc2 {
> > +	regulator-always-on;
> > +	regulator-min-microvolt = <1040000>;
> > +	regulator-max-microvolt = <1300000>;
> > +	regulator-name = "vdd-cpux";
> > +};
> > +
> > +/* DCDC3 is polyphased with DCDC2 */
> > +
> > +&reg_dcdc5 {
> > +	regulator-always-on;
> > +	regulator-min-microvolt = <1500000>;
> > +	regulator-max-microvolt = <1500000>;
> > +	regulator-name = "vcc-dram";
> > +};
> > +
> > +/* Deviates from the reset default of 1.1V. */
> > +&reg_dcdc6 {
> > +	regulator-always-on;
> > +	regulator-min-microvolt = <1200000>;
> > +	regulator-max-microvolt = <1200000>;
> > +	regulator-name = "vdd-sys";
> > +};
> > +
> > +&reg_aldo1 {
> > +	regulator-min-microvolt = <3300000>;
> > +	regulator-max-microvolt = <3300000>;
> > +	regulator-name = "vcc-wifi";
> > +};
> > +
> > +&reg_aldo2 {
> > +	/* Specifying R_PIO consumer would create circular dependency. */
> > +	regulator-always-on;
> > +	regulator-min-microvolt = <3300000>;
> > +	regulator-max-microvolt = <3300000>;
> > +	regulator-name = "vcc-pl";
> > +};
> > +
> > +&reg_aldo3 {
> > +	regulator-always-on;
> > +	regulator-min-microvolt = <3000000>;
> > +	regulator-max-microvolt = <3000000>;
> > +	regulator-name = "vcc-pll-avcc";
> > +};
> > +
> > +/* AC200 power supply */
> > +&reg_dldo1 {
> > +	regulator-always-on;
> > +	regulator-min-microvolt = <3300000>;
> > +	regulator-max-microvolt = <3300000>;
> > +	regulator-name = "vcc-ave-33";
> > +};
> > +
> > +&reg_dldo4 {
> > +	regulator-min-microvolt = <3300000>;
> > +	regulator-max-microvolt = <3300000>;
> > +	regulator-name = "vcc-wifi-io";
> > +};
> > +
> > +&reg_drivevbus {
> > +	regulator-name = "usb0-vbus";
> > +	status = "okay";
> > +};
> > +
> > +&reg_eldo1 {
> > +	regulator-always-on;
> > +	regulator-min-microvolt = <1800000>;
> > +	regulator-max-microvolt = <1800000>;
> > +	regulator-name = "vcc-cpvdd-dram-emmc";
> > +};
> > +
> > +/* Supplies the arisc management core, needed by TF-A to power off cores. */
> > +&reg_fldo2 {
> > +	regulator-always-on;
> > +	regulator-min-microvolt = <1100000>;
> > +	regulator-max-microvolt = <1100000>;
> > +	regulator-name = "vdd-cpus";
> > +};
> > +
> > +&reg_rtc_ldo {
> > +	regulator-name = "vcc-rtc";
> > +};
> > +
> > +&simplefb_hdmi {
> > +	vcc-hdmi-supply = <&reg_dcdc1>;
> > +};
> > +
> > +&sound {
> > +	simple-audio-card,aux-devs = <&codec_analog>;
> > +	simple-audio-card,widgets = "Microphone", "Microphone Jack",
> > +				    "Headphone", "Headphone Jack";
> > +	simple-audio-card,routing =
> > +			"Left DAC", "DACL",
> > +			"Right DAC", "DACR",
> > +			"Headphone Jack", "HP",
> > +			"ADCL", "Left ADC",
> > +			"ADCR", "Right ADC",
> > +			"MIC2", "Microphone Jack";
> > +	status = "okay";
> > +};
> > +
> > +/* On the (unpopulated) UART pads. */
> > +&uart0 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&uart0_pb_pins>;
> > +	status = "okay";
> > +};
> > +
> > +&uart1 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> > +	uart-has-rtscts;
> > +	status = "okay";
> > +
> > +	bluetooth {
> > +		compatible = "realtek,rtl8723bs-bt";
> > +		enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> > +		max-speed = <1500000>;
> > +	};
> > +};
> > +
> > +&usb_otg {
> > +	dr_mode = "host";
> > +	status = "okay";
> > +};
> > +
> > +&usbphy {
> > +	usb0_vbus-supply = <&reg_drivevbus>;
> > +	usb1_vbus-supply = <&reg_drivevbus>;
> > +	status = "okay";
> > +};
> > 
> 
> 
> 
> 
>

Andre Przywara Feb. 6, 2024, 12:47 a.m. UTC | #3

Hi Jernej,

thanks for having a look!

On 05/02/2024 19:20, Jernej Škrabec wrote:
> Dne ponedeljek, 05. februar 2024 ob 19:12:45 CET je Jernej Škrabec napisal(a):
>> Hi Andre!
>>
>> Dne nedelja, 04. februar 2024 ob 10:44:04 CET je Andre Przywara napisal(a):
>>> The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
>>> which appears to be just a relabelled A64. It was launched in 2015 by
>>> the now defunct company Jide, and shipped with a desktop optimised
>>> version of Android. It features
>>> 	- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
>>> 	- 1 or 2 GB DRAM
>>> 	- 8 or 16 GB eMMC flash
>>> 	- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
>>> 	- RTL8723BS WiFi & Bluetooth chip
>>> 	- HDMI port
>>> 	- two USB 2.0 ports
>>> 	- 3.5mm AV port
>>> 	- microSD card slot
>>>
>>> The devicetree covers most peripherals, though there is no agreed
>>> binding for the PHY chip yet, so this is left out.
>>>
>>> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
>>> ---
>>>   arch/arm64/boot/dts/allwinner/Makefile        |   1 +
>>>   .../allwinner/sun50i-h64-remix-mini-pc.dts    | 357 ++++++++++++++++++
>>>   2 files changed, 358 insertions(+)
>>>   create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
>>>
>>> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
>>> index 91d505b385de..2db3b15ad09f 100644
>>> --- a/arch/arm64/boot/dts/allwinner/Makefile
>>> +++ b/arch/arm64/boot/dts/allwinner/Makefile
>>> @@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
>>>   dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab-early-adopter.dtb
>>>   dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
>>>   dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
>>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h64-remix-mini-pc.dtb
>>>   dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb
>>>   dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
>>>   dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
>>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
>>> new file mode 100644
>>> index 000000000000..537923a541a8
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
>>> @@ -0,0 +1,357 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>>> +// Copyright (c) 2018 ARM Ltd.
>>
>> Shouldn't be 2024?

Well, that just documents that sad fact that I indeed created this file 
6 years ago, but just managed now to actually send this. Is there a 
requirement for this being "recent"?

>>
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "sun50i-a64.dtsi"
>>> +#include "sun50i-a64-cpu-opp.dtsi"
>>> +
>>> +#include <dt-bindings/gpio/gpio.h>
>>> +
>>> +/ {
>>> +	model = "Remix Mini PC";
>>> +	compatible = "jide,remix-mini-pc", "allwinner,sun50i-h64",
>>> +		     "allwinner,sun50i-a64";
>>> +
>>> +	aliases {
>>> +		ethernet1 = &rtl8723bs;
>>> +		serial0 = &uart0;
>>> +	};
>>> +
>>> +	chosen {
>>> +		stdout-path = "serial0:115200n8";
>>> +	};
>>> +
>>> +	hdmi-connector {
>>> +		compatible = "hdmi-connector";
>>> +		type = "a";
>>> +
>>> +		port {
>>> +			hdmi_con_in: endpoint {
>>> +				remote-endpoint = <&hdmi_out_con>;
>>> +			};
>>> +		};
>>> +	};
>>> +
>>> +	reg_vcc5v: regulator-5v {
>>> +		/* board wide 5V supply directly from the DC input */
>>> +		compatible = "regulator-fixed";
>>> +		regulator-name = "vcc-5v";
>>> +		regulator-min-microvolt = <5000000>;
>>> +		regulator-max-microvolt = <5000000>;
>>> +		regulator-always-on;
>>> +	};
>>> +
>>> +	wifi_pwrseq: wifi_pwrseq {
>>> +		compatible = "mmc-pwrseq-simple";
>>> +		pinctrl-names = "default";
>>> +		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
>>> +		post-power-on-delay-ms = <200>;
>>> +	};
>>> +};
>>> +
>>> +&codec {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&codec_analog {
>>> +	cpvdd-supply = <&reg_eldo1>;
>>> +	status = "okay";
>>> +};
>>> +
>>> +&cpu0 {
>>> +	cpu-supply = <&reg_dcdc2>;
>>> +};
>>> +
>>> +&cpu1 {
>>> +	cpu-supply = <&reg_dcdc2>;
>>> +};
>>> +
>>> +&cpu2 {
>>> +	cpu-supply = <&reg_dcdc2>;
>>> +};
>>> +
>>> +&cpu3 {
>>> +	cpu-supply = <&reg_dcdc2>;
>>> +};
>>> +
>>> +&dai {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&de {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&ehci0 {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&ehci1 {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&hdmi {
>>> +	hvcc-supply = <&reg_dldo1>;
>>> +	status = "okay";
>>> +};
>>> +
>>> +&hdmi_out {
>>> +	hdmi_out_con: endpoint {
>>> +		remote-endpoint = <&hdmi_con_in>;
>>> +	};
>>> +};
>>> +
>>> +/* Connects to the AC200 chip */
>>> +&i2c0 {
>>> +	pinctrl-names = "default";
>>> +	pinctrl-0 = <&i2c0_pins>;
>>> +	status = "okay";
>>> +};
>>> +
>>> +&i2c0_pins {
>>> +	bias-pull-up;
>>> +};
>>> +
>>> +&mmc0 {
>>> +	pinctrl-names = "default";
>>> +	pinctrl-0 = <&mmc0_pins>;
>>> +	vmmc-supply = <&reg_dcdc1>;
>>> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
>>> +	disable-wp;
>>> +	bus-width = <4>;
>>> +	status = "okay";
>>> +};
>>> +
>>> +&mmc1 {
>>> +	pinctrl-names = "default";
>>> +	pinctrl-0 = <&mmc1_pins>;
>>> +	vmmc-supply = <&reg_aldo1>;
>>> +	vqmmc-supply = <&reg_dldo4>;
>>> +	mmc-pwrseq = <&wifi_pwrseq>;
>>> +	bus-width = <4>;
>>> +	non-removable;
>>> +	status = "okay";
>>> +
>>> +	rtl8723bs: wifi@1 {
>>> +		reg = <1>;
>>> +		interrupt-parent = <&r_pio>;
>>> +		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
>>> +		interrupt-names = "host-wake";
>>> +	};
>>
>> Node without compatible doesn't help. Please remove it.

Huh, but where do I put the the IRQ line then? And every other RTL8723BS 
user seems to do the same?

>>
>>> +};
>>> +
>>> +&mmc2 {
>>> +	pinctrl-names = "default";
>>> +	pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
>>> +	vmmc-supply = <&reg_dcdc1>;
>>> +	vqmmc-supply = <&reg_eldo1>;
>>> +	bus-width = <8>;
>>> +	non-removable;
>>> +	mmc-ddr-1_8v;
>>> +	mmc-hs200-1_8v;
>>
>> Aren't these speed modes enabled by default?

Enabled by who? Our current sunxi-mmc driver? I cannot find anything in 
the binding that suggests that there would be some default settings.

> Sorry, mmc-hs200-1_8v is ok, but mmc-ddr-1_8v should be
> removed.

Mmh, I am confused: I thought after the H5 eMMC mishap we figured that 
all speed modes supported by the eMMC chip should be listed in the DT?
So any driver wouldn't need to make assumptions, and if a particular 
mode shows problems on a board, we just remove that mode from the DT.
Actually, thinking about that, I guess I should list HS-400 as well? The 
BSP kernel uses that mode.
Or do you mean to say that in particular DDR (@1.8V) is problematic? I 
cannot test at the moment, but could try later to force that mode.

Cheers,
Andre


>>> +	cap-mmc-hw-reset;
>>> +	status = "okay";
>>> +};
>>> +
>>> +&ohci0 {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&ohci1 {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&pio {
>>> +	vcc-pb-supply = <&reg_dcdc1>;
>>> +	vcc-pc-supply = <&reg_dcdc1>;
>>> +	vcc-pd-supply = <&reg_dcdc1>;
>>> +	vcc-pe-supply = <&reg_dcdc1>;
>>> +	vcc-pf-supply = <&reg_dcdc1>;
>>> +	vcc-pg-supply = <&reg_dldo4>;
>>> +	vcc-ph-supply = <&reg_dcdc1>;
>>> +};
>>> +
>>> +&r_ir {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&r_pio {
>>> +	/*
>>> +	 * We cannot add that supply for now since it would create a circular
>>> +	 * dependency between pinctrl, the regulator and the RSB Bus.
>>> +	 *
>>> +	 * vcc-pl-supply = <&reg_aldo2>;
>>> +	 */
>>> +};
>>> +
>>> +&r_rsb {
>>> +	status = "okay";
>>> +
>>> +	axp803: pmic@3a3 {
>>> +		compatible = "x-powers,axp803";
>>> +		reg = <0x3a3>;
>>> +		interrupt-parent = <&r_intc>;
>>> +		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_LOW>;
>>> +		x-powers,drive-vbus-en;
>>> +
>>> +		vin1-supply = <&reg_vcc5v>;
>>> +		vin2-supply = <&reg_vcc5v>;
>>> +		vin3-supply = <&reg_vcc5v>;
>>> +		vin5-supply = <&reg_vcc5v>;
>>> +		vin6-supply = <&reg_vcc5v>;
>>> +		aldoin-supply = <&reg_vcc5v>;
>>> +		dldoin-supply = <&reg_vcc5v>;
>>> +		eldoin-supply = <&reg_vcc5v>;
>>> +		fldoin-supply = <&reg_vcc5v>;
>>> +		drivevbus-supply = <&reg_vcc5v>;
>>> +		ips-supply = <&reg_vcc5v>;
>>> +
>>> +		status = "okay";
>>> +	};
>>> +};
>>> +
>>> +#include "axp803.dtsi"
>>> +
>>> +&ac_power_supply {
>>> +	status = "okay";
>>> +};
>>> +
>>> +&reg_dcdc1 {
>>> +	regulator-always-on;
>>> +	regulator-min-microvolt = <3300000>;
>>> +	regulator-max-microvolt = <3300000>;
>>> +	regulator-name = "vcc-3v3";
>>> +};
>>> +
>>> +&reg_dcdc2 {
>>> +	regulator-always-on;
>>> +	regulator-min-microvolt = <1040000>;
>>> +	regulator-max-microvolt = <1300000>;
>>> +	regulator-name = "vdd-cpux";
>>> +};
>>> +
>>> +/* DCDC3 is polyphased with DCDC2 */
>>> +
>>> +&reg_dcdc5 {
>>> +	regulator-always-on;
>>> +	regulator-min-microvolt = <1500000>;
>>> +	regulator-max-microvolt = <1500000>;
>>> +	regulator-name = "vcc-dram";
>>> +};
>>> +
>>> +/* Deviates from the reset default of 1.1V. */
>>> +&reg_dcdc6 {
>>> +	regulator-always-on;
>>> +	regulator-min-microvolt = <1200000>;
>>> +	regulator-max-microvolt = <1200000>;
>>> +	regulator-name = "vdd-sys";
>>> +};
>>> +
>>> +&reg_aldo1 {
>>> +	regulator-min-microvolt = <3300000>;
>>> +	regulator-max-microvolt = <3300000>;
>>> +	regulator-name = "vcc-wifi";
>>> +};
>>> +
>>> +&reg_aldo2 {
>>> +	/* Specifying R_PIO consumer would create circular dependency. */
>>> +	regulator-always-on;
>>> +	regulator-min-microvolt = <3300000>;
>>> +	regulator-max-microvolt = <3300000>;
>>> +	regulator-name = "vcc-pl";
>>> +};
>>> +
>>> +&reg_aldo3 {
>>> +	regulator-always-on;
>>> +	regulator-min-microvolt = <3000000>;
>>> +	regulator-max-microvolt = <3000000>;
>>> +	regulator-name = "vcc-pll-avcc";
>>> +};
>>> +
>>> +/* AC200 power supply */
>>> +&reg_dldo1 {
>>> +	regulator-always-on;
>>> +	regulator-min-microvolt = <3300000>;
>>> +	regulator-max-microvolt = <3300000>;
>>> +	regulator-name = "vcc-ave-33";
>>> +};
>>> +
>>> +&reg_dldo4 {
>>> +	regulator-min-microvolt = <3300000>;
>>> +	regulator-max-microvolt = <3300000>;
>>> +	regulator-name = "vcc-wifi-io";
>>> +};
>>> +
>>> +&reg_drivevbus {
>>> +	regulator-name = "usb0-vbus";
>>> +	status = "okay";
>>> +};
>>> +
>>> +&reg_eldo1 {
>>> +	regulator-always-on;
>>> +	regulator-min-microvolt = <1800000>;
>>> +	regulator-max-microvolt = <1800000>;
>>> +	regulator-name = "vcc-cpvdd-dram-emmc";
>>> +};
>>> +
>>> +/* Supplies the arisc management core, needed by TF-A to power off cores. */
>>> +&reg_fldo2 {
>>> +	regulator-always-on;
>>> +	regulator-min-microvolt = <1100000>;
>>> +	regulator-max-microvolt = <1100000>;
>>> +	regulator-name = "vdd-cpus";
>>> +};
>>> +
>>> +&reg_rtc_ldo {
>>> +	regulator-name = "vcc-rtc";
>>> +};
>>> +
>>> +&simplefb_hdmi {
>>> +	vcc-hdmi-supply = <&reg_dcdc1>;
>>> +};
>>> +
>>> +&sound {
>>> +	simple-audio-card,aux-devs = <&codec_analog>;
>>> +	simple-audio-card,widgets = "Microphone", "Microphone Jack",
>>> +				    "Headphone", "Headphone Jack";
>>> +	simple-audio-card,routing =
>>> +			"Left DAC", "DACL",
>>> +			"Right DAC", "DACR",
>>> +			"Headphone Jack", "HP",
>>> +			"ADCL", "Left ADC",
>>> +			"ADCR", "Right ADC",
>>> +			"MIC2", "Microphone Jack";
>>> +	status = "okay";
>>> +};
>>> +
>>> +/* On the (unpopulated) UART pads. */
>>> +&uart0 {
>>> +	pinctrl-names = "default";
>>> +	pinctrl-0 = <&uart0_pb_pins>;
>>> +	status = "okay";
>>> +};
>>> +
>>> +&uart1 {
>>> +	pinctrl-names = "default";
>>> +	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
>>> +	uart-has-rtscts;
>>> +	status = "okay";
>>> +
>>> +	bluetooth {
>>> +		compatible = "realtek,rtl8723bs-bt";
>>> +		enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
>>> +		max-speed = <1500000>;
>>> +	};
>>> +};
>>> +
>>> +&usb_otg {
>>> +	dr_mode = "host";
>>> +	status = "okay";
>>> +};
>>> +
>>> +&usbphy {
>>> +	usb0_vbus-supply = <&reg_drivevbus>;
>>> +	usb1_vbus-supply = <&reg_drivevbus>;
>>> +	status = "okay";
>>> +};
>>>
>>
>>
>>
>>
>>
> 
> 
> 
>

Jernej Škrabec Feb. 6, 2024, 5:32 p.m. UTC | #4

Dne torek, 06. februar 2024 ob 01:47:05 CET je Andre Przywara napisal(a):
> Hi Jernej,
> 
> thanks for having a look!
> 
> On 05/02/2024 19:20, Jernej Škrabec wrote:
> > Dne ponedeljek, 05. februar 2024 ob 19:12:45 CET je Jernej Škrabec napisal(a):
> >> Hi Andre!
> >>
> >> Dne nedelja, 04. februar 2024 ob 10:44:04 CET je Andre Przywara napisal(a):
> >>> The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
> >>> which appears to be just a relabelled A64. It was launched in 2015 by
> >>> the now defunct company Jide, and shipped with a desktop optimised
> >>> version of Android. It features
> >>> 	- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
> >>> 	- 1 or 2 GB DRAM
> >>> 	- 8 or 16 GB eMMC flash
> >>> 	- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
> >>> 	- RTL8723BS WiFi & Bluetooth chip
> >>> 	- HDMI port
> >>> 	- two USB 2.0 ports
> >>> 	- 3.5mm AV port
> >>> 	- microSD card slot
> >>>
> >>> The devicetree covers most peripherals, though there is no agreed
> >>> binding for the PHY chip yet, so this is left out.
> >>>
> >>> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> >>> ---
> >>>   arch/arm64/boot/dts/allwinner/Makefile        |   1 +
> >>>   .../allwinner/sun50i-h64-remix-mini-pc.dts    | 357 ++++++++++++++++++
> >>>   2 files changed, 358 insertions(+)
> >>>   create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> >>>
> >>> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> >>> index 91d505b385de..2db3b15ad09f 100644
> >>> --- a/arch/arm64/boot/dts/allwinner/Makefile
> >>> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> >>> @@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
> >>>   dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab-early-adopter.dtb
> >>>   dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
> >>>   dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
> >>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h64-remix-mini-pc.dtb
> >>>   dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb
> >>>   dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
> >>>   dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
> >>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> >>> new file mode 100644
> >>> index 000000000000..537923a541a8
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> >>> @@ -0,0 +1,357 @@
> >>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> >>> +// Copyright (c) 2018 ARM Ltd.
> >>
> >> Shouldn't be 2024?
> 
> Well, that just documents that sad fact that I indeed created this file 
> 6 years ago, but just managed now to actually send this. Is there a 
> requirement for this being "recent"?

Not really, but it's strange looking. Some might incorrectly assume that it's
present in the kernel longer than it really is.

> 
> >>
> >>> +
> >>> +/dts-v1/;
> >>> +
> >>> +#include "sun50i-a64.dtsi"
> >>> +#include "sun50i-a64-cpu-opp.dtsi"
> >>> +
> >>> +#include <dt-bindings/gpio/gpio.h>
> >>> +
> >>> +/ {
> >>> +	model = "Remix Mini PC";
> >>> +	compatible = "jide,remix-mini-pc", "allwinner,sun50i-h64",
> >>> +		     "allwinner,sun50i-a64";
> >>> +
> >>> +	aliases {
> >>> +		ethernet1 = &rtl8723bs;
> >>> +		serial0 = &uart0;
> >>> +	};
> >>> +
> >>> +	chosen {
> >>> +		stdout-path = "serial0:115200n8";
> >>> +	};
> >>> +
> >>> +	hdmi-connector {
> >>> +		compatible = "hdmi-connector";
> >>> +		type = "a";
> >>> +
> >>> +		port {
> >>> +			hdmi_con_in: endpoint {
> >>> +				remote-endpoint = <&hdmi_out_con>;
> >>> +			};
> >>> +		};
> >>> +	};
> >>> +
> >>> +	reg_vcc5v: regulator-5v {
> >>> +		/* board wide 5V supply directly from the DC input */
> >>> +		compatible = "regulator-fixed";
> >>> +		regulator-name = "vcc-5v";
> >>> +		regulator-min-microvolt = <5000000>;
> >>> +		regulator-max-microvolt = <5000000>;
> >>> +		regulator-always-on;
> >>> +	};
> >>> +
> >>> +	wifi_pwrseq: wifi_pwrseq {
> >>> +		compatible = "mmc-pwrseq-simple";
> >>> +		pinctrl-names = "default";
> >>> +		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
> >>> +		post-power-on-delay-ms = <200>;
> >>> +	};
> >>> +};
> >>> +
> >>> +&codec {
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&codec_analog {
> >>> +	cpvdd-supply = <&reg_eldo1>;
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&cpu0 {
> >>> +	cpu-supply = <&reg_dcdc2>;
> >>> +};
> >>> +
> >>> +&cpu1 {
> >>> +	cpu-supply = <&reg_dcdc2>;
> >>> +};
> >>> +
> >>> +&cpu2 {
> >>> +	cpu-supply = <&reg_dcdc2>;
> >>> +};
> >>> +
> >>> +&cpu3 {
> >>> +	cpu-supply = <&reg_dcdc2>;
> >>> +};
> >>> +
> >>> +&dai {
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&de {
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&ehci0 {
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&ehci1 {
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&hdmi {
> >>> +	hvcc-supply = <&reg_dldo1>;
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&hdmi_out {
> >>> +	hdmi_out_con: endpoint {
> >>> +		remote-endpoint = <&hdmi_con_in>;
> >>> +	};
> >>> +};
> >>> +
> >>> +/* Connects to the AC200 chip */
> >>> +&i2c0 {
> >>> +	pinctrl-names = "default";
> >>> +	pinctrl-0 = <&i2c0_pins>;
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&i2c0_pins {
> >>> +	bias-pull-up;
> >>> +};
> >>> +
> >>> +&mmc0 {
> >>> +	pinctrl-names = "default";
> >>> +	pinctrl-0 = <&mmc0_pins>;
> >>> +	vmmc-supply = <&reg_dcdc1>;
> >>> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> >>> +	disable-wp;
> >>> +	bus-width = <4>;
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&mmc1 {
> >>> +	pinctrl-names = "default";
> >>> +	pinctrl-0 = <&mmc1_pins>;
> >>> +	vmmc-supply = <&reg_aldo1>;
> >>> +	vqmmc-supply = <&reg_dldo4>;
> >>> +	mmc-pwrseq = <&wifi_pwrseq>;
> >>> +	bus-width = <4>;
> >>> +	non-removable;
> >>> +	status = "okay";
> >>> +
> >>> +	rtl8723bs: wifi@1 {
> >>> +		reg = <1>;
> >>> +		interrupt-parent = <&r_pio>;
> >>> +		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
> >>> +		interrupt-names = "host-wake";
> >>> +	};
> >>
> >> Node without compatible doesn't help. Please remove it.
> 
> Huh, but where do I put the the IRQ line then? And every other RTL8723BS 
> user seems to do the same?

It's good, sorry for the noise.

> 
> >>
> >>> +};
> >>> +
> >>> +&mmc2 {
> >>> +	pinctrl-names = "default";
> >>> +	pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
> >>> +	vmmc-supply = <&reg_dcdc1>;
> >>> +	vqmmc-supply = <&reg_eldo1>;
> >>> +	bus-width = <8>;
> >>> +	non-removable;
> >>> +	mmc-ddr-1_8v;
> >>> +	mmc-hs200-1_8v;
> >>
> >> Aren't these speed modes enabled by default?
> 
> Enabled by who? Our current sunxi-mmc driver? I cannot find anything in 
> the binding that suggests that there would be some default settings.

Looking at Linux sunxi mmc driver, mmc-ddr-1_8v is enabled by default for
"new timings" variants except for H5. Anyway...

> 
> > Sorry, mmc-hs200-1_8v is ok, but mmc-ddr-1_8v should be
> > removed.
> 
> Mmh, I am confused: I thought after the H5 eMMC mishap we figured that 
> all speed modes supported by the eMMC chip should be listed in the DT?

I think H5 just has (had?) driver issue. From what I can see, only highest
supported mode by kernel and chip is specified in all Allwinner DTs.
mmc-ddr-1_8v is only specified by two recent board addition, where I missed
it while reviewing.

> So any driver wouldn't need to make assumptions, and if a particular 
> mode shows problems on a board, we just remove that mode from the DT.
> Actually, thinking about that, I guess I should list HS-400 as well? The 
> BSP kernel uses that mode.

Sure, but it also calibrates timing for it. If you'll specify HS400, kernel
will try to use it, but it won't work.

> Or do you mean to say that in particular DDR (@1.8V) is problematic? I 
> cannot test at the moment, but could try later to force that mode.

No, no need.

Best regards,
Jernej

> 
> Cheers,
> Andre
> 
> 
> >>> +	cap-mmc-hw-reset;
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&ohci0 {
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&ohci1 {
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&pio {
> >>> +	vcc-pb-supply = <&reg_dcdc1>;
> >>> +	vcc-pc-supply = <&reg_dcdc1>;
> >>> +	vcc-pd-supply = <&reg_dcdc1>;
> >>> +	vcc-pe-supply = <&reg_dcdc1>;
> >>> +	vcc-pf-supply = <&reg_dcdc1>;
> >>> +	vcc-pg-supply = <&reg_dldo4>;
> >>> +	vcc-ph-supply = <&reg_dcdc1>;
> >>> +};
> >>> +
> >>> +&r_ir {
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&r_pio {
> >>> +	/*
> >>> +	 * We cannot add that supply for now since it would create a circular
> >>> +	 * dependency between pinctrl, the regulator and the RSB Bus.
> >>> +	 *
> >>> +	 * vcc-pl-supply = <&reg_aldo2>;
> >>> +	 */
> >>> +};
> >>> +
> >>> +&r_rsb {
> >>> +	status = "okay";
> >>> +
> >>> +	axp803: pmic@3a3 {
> >>> +		compatible = "x-powers,axp803";
> >>> +		reg = <0x3a3>;
> >>> +		interrupt-parent = <&r_intc>;
> >>> +		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_LOW>;
> >>> +		x-powers,drive-vbus-en;
> >>> +
> >>> +		vin1-supply = <&reg_vcc5v>;
> >>> +		vin2-supply = <&reg_vcc5v>;
> >>> +		vin3-supply = <&reg_vcc5v>;
> >>> +		vin5-supply = <&reg_vcc5v>;
> >>> +		vin6-supply = <&reg_vcc5v>;
> >>> +		aldoin-supply = <&reg_vcc5v>;
> >>> +		dldoin-supply = <&reg_vcc5v>;
> >>> +		eldoin-supply = <&reg_vcc5v>;
> >>> +		fldoin-supply = <&reg_vcc5v>;
> >>> +		drivevbus-supply = <&reg_vcc5v>;
> >>> +		ips-supply = <&reg_vcc5v>;
> >>> +
> >>> +		status = "okay";
> >>> +	};
> >>> +};
> >>> +
> >>> +#include "axp803.dtsi"
> >>> +
> >>> +&ac_power_supply {
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&reg_dcdc1 {
> >>> +	regulator-always-on;
> >>> +	regulator-min-microvolt = <3300000>;
> >>> +	regulator-max-microvolt = <3300000>;
> >>> +	regulator-name = "vcc-3v3";
> >>> +};
> >>> +
> >>> +&reg_dcdc2 {
> >>> +	regulator-always-on;
> >>> +	regulator-min-microvolt = <1040000>;
> >>> +	regulator-max-microvolt = <1300000>;
> >>> +	regulator-name = "vdd-cpux";
> >>> +};
> >>> +
> >>> +/* DCDC3 is polyphased with DCDC2 */
> >>> +
> >>> +&reg_dcdc5 {
> >>> +	regulator-always-on;
> >>> +	regulator-min-microvolt = <1500000>;
> >>> +	regulator-max-microvolt = <1500000>;
> >>> +	regulator-name = "vcc-dram";
> >>> +};
> >>> +
> >>> +/* Deviates from the reset default of 1.1V. */
> >>> +&reg_dcdc6 {
> >>> +	regulator-always-on;
> >>> +	regulator-min-microvolt = <1200000>;
> >>> +	regulator-max-microvolt = <1200000>;
> >>> +	regulator-name = "vdd-sys";
> >>> +};
> >>> +
> >>> +&reg_aldo1 {
> >>> +	regulator-min-microvolt = <3300000>;
> >>> +	regulator-max-microvolt = <3300000>;
> >>> +	regulator-name = "vcc-wifi";
> >>> +};
> >>> +
> >>> +&reg_aldo2 {
> >>> +	/* Specifying R_PIO consumer would create circular dependency. */
> >>> +	regulator-always-on;
> >>> +	regulator-min-microvolt = <3300000>;
> >>> +	regulator-max-microvolt = <3300000>;
> >>> +	regulator-name = "vcc-pl";
> >>> +};
> >>> +
> >>> +&reg_aldo3 {
> >>> +	regulator-always-on;
> >>> +	regulator-min-microvolt = <3000000>;
> >>> +	regulator-max-microvolt = <3000000>;
> >>> +	regulator-name = "vcc-pll-avcc";
> >>> +};
> >>> +
> >>> +/* AC200 power supply */
> >>> +&reg_dldo1 {
> >>> +	regulator-always-on;
> >>> +	regulator-min-microvolt = <3300000>;
> >>> +	regulator-max-microvolt = <3300000>;
> >>> +	regulator-name = "vcc-ave-33";
> >>> +};
> >>> +
> >>> +&reg_dldo4 {
> >>> +	regulator-min-microvolt = <3300000>;
> >>> +	regulator-max-microvolt = <3300000>;
> >>> +	regulator-name = "vcc-wifi-io";
> >>> +};
> >>> +
> >>> +&reg_drivevbus {
> >>> +	regulator-name = "usb0-vbus";
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&reg_eldo1 {
> >>> +	regulator-always-on;
> >>> +	regulator-min-microvolt = <1800000>;
> >>> +	regulator-max-microvolt = <1800000>;
> >>> +	regulator-name = "vcc-cpvdd-dram-emmc";
> >>> +};
> >>> +
> >>> +/* Supplies the arisc management core, needed by TF-A to power off cores. */
> >>> +&reg_fldo2 {
> >>> +	regulator-always-on;
> >>> +	regulator-min-microvolt = <1100000>;
> >>> +	regulator-max-microvolt = <1100000>;
> >>> +	regulator-name = "vdd-cpus";
> >>> +};
> >>> +
> >>> +&reg_rtc_ldo {
> >>> +	regulator-name = "vcc-rtc";
> >>> +};
> >>> +
> >>> +&simplefb_hdmi {
> >>> +	vcc-hdmi-supply = <&reg_dcdc1>;
> >>> +};
> >>> +
> >>> +&sound {
> >>> +	simple-audio-card,aux-devs = <&codec_analog>;
> >>> +	simple-audio-card,widgets = "Microphone", "Microphone Jack",
> >>> +				    "Headphone", "Headphone Jack";
> >>> +	simple-audio-card,routing =
> >>> +			"Left DAC", "DACL",
> >>> +			"Right DAC", "DACR",
> >>> +			"Headphone Jack", "HP",
> >>> +			"ADCL", "Left ADC",
> >>> +			"ADCR", "Right ADC",
> >>> +			"MIC2", "Microphone Jack";
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +/* On the (unpopulated) UART pads. */
> >>> +&uart0 {
> >>> +	pinctrl-names = "default";
> >>> +	pinctrl-0 = <&uart0_pb_pins>;
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&uart1 {
> >>> +	pinctrl-names = "default";
> >>> +	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> >>> +	uart-has-rtscts;
> >>> +	status = "okay";
> >>> +
> >>> +	bluetooth {
> >>> +		compatible = "realtek,rtl8723bs-bt";
> >>> +		enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> >>> +		max-speed = <1500000>;
> >>> +	};
> >>> +};
> >>> +
> >>> +&usb_otg {
> >>> +	dr_mode = "host";
> >>> +	status = "okay";
> >>> +};
> >>> +
> >>> +&usbphy {
> >>> +	usb0_vbus-supply = <&reg_drivevbus>;
> >>> +	usb1_vbus-supply = <&reg_drivevbus>;
> >>> +	status = "okay";
> >>> +};
> >>>
> >>
> >>
> >>
> >>
> >>
> > 
> > 
> > 
> > 
>

Andre Przywara Feb. 6, 2024, 6:13 p.m. UTC | #5

Hi Jernej,

On 06/02/2024 18:32, Jernej Škrabec wrote:
> Dne torek, 06. februar 2024 ob 01:47:05 CET je Andre Przywara napisal(a):
>> Hi Jernej,
>>
>> thanks for having a look!
>>
>> On 05/02/2024 19:20, Jernej Škrabec wrote:
>>> Dne ponedeljek, 05. februar 2024 ob 19:12:45 CET je Jernej Škrabec napisal(a):
>>>> Hi Andre!
>>>>
>>>> Dne nedelja, 04. februar 2024 ob 10:44:04 CET je Andre Przywara napisal(a):
>>>>> The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
>>>>> which appears to be just a relabelled A64. It was launched in 2015 by
>>>>> the now defunct company Jide, and shipped with a desktop optimised
>>>>> version of Android. It features
>>>>> 	- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
>>>>> 	- 1 or 2 GB DRAM
>>>>> 	- 8 or 16 GB eMMC flash
>>>>> 	- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
>>>>> 	- RTL8723BS WiFi & Bluetooth chip
>>>>> 	- HDMI port
>>>>> 	- two USB 2.0 ports
>>>>> 	- 3.5mm AV port
>>>>> 	- microSD card slot
>>>>>
>>>>> The devicetree covers most peripherals, though there is no agreed
>>>>> binding for the PHY chip yet, so this is left out.
>>>>>
>>>>> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
>>>>> ---
>>>>>    arch/arm64/boot/dts/allwinner/Makefile        |   1 +
>>>>>    .../allwinner/sun50i-h64-remix-mini-pc.dts    | 357 ++++++++++++++++++
>>>>>    2 files changed, 358 insertions(+)
>>>>>    create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
>>>>>
>>>>> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
>>>>> index 91d505b385de..2db3b15ad09f 100644
>>>>> --- a/arch/arm64/boot/dts/allwinner/Makefile
>>>>> +++ b/arch/arm64/boot/dts/allwinner/Makefile
>>>>> @@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
>>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab-early-adopter.dtb
>>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
>>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
>>>>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h64-remix-mini-pc.dtb
>>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb
>>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
>>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
>>>>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
>>>>> new file mode 100644
>>>>> index 000000000000..537923a541a8
>>>>> --- /dev/null
>>>>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
>>>>> @@ -0,0 +1,357 @@
>>>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>>>>> +// Copyright (c) 2018 ARM Ltd.
>>>>
>>>> Shouldn't be 2024?
>>
>> Well, that just documents that sad fact that I indeed created this file
>> 6 years ago, but just managed now to actually send this. Is there a
>> requirement for this being "recent"?
> 
> Not really, but it's strange looking. Some might incorrectly assume that it's
> present in the kernel longer than it really is.

OK, I will put in 2023, as this is when I touched this again.

>>>>
>>>>> +
>>>>> +/dts-v1/;
>>>>> +
>>>>> +#include "sun50i-a64.dtsi"
>>>>> +#include "sun50i-a64-cpu-opp.dtsi"
>>>>> +
>>>>> +#include <dt-bindings/gpio/gpio.h>
>>>>> +
>>>>> +/ {
>>>>> +	model = "Remix Mini PC";
>>>>> +	compatible = "jide,remix-mini-pc", "allwinner,sun50i-h64",
>>>>> +		     "allwinner,sun50i-a64";
>>>>> +
>>>>> +	aliases {
>>>>> +		ethernet1 = &rtl8723bs;
>>>>> +		serial0 = &uart0;
>>>>> +	};
>>>>> +
>>>>> +	chosen {
>>>>> +		stdout-path = "serial0:115200n8";
>>>>> +	};
>>>>> +
>>>>> +	hdmi-connector {
>>>>> +		compatible = "hdmi-connector";
>>>>> +		type = "a";
>>>>> +
>>>>> +		port {
>>>>> +			hdmi_con_in: endpoint {
>>>>> +				remote-endpoint = <&hdmi_out_con>;
>>>>> +			};
>>>>> +		};
>>>>> +	};
>>>>> +
>>>>> +	reg_vcc5v: regulator-5v {
>>>>> +		/* board wide 5V supply directly from the DC input */
>>>>> +		compatible = "regulator-fixed";
>>>>> +		regulator-name = "vcc-5v";
>>>>> +		regulator-min-microvolt = <5000000>;
>>>>> +		regulator-max-microvolt = <5000000>;
>>>>> +		regulator-always-on;
>>>>> +	};
>>>>> +
>>>>> +	wifi_pwrseq: wifi_pwrseq {
>>>>> +		compatible = "mmc-pwrseq-simple";
>>>>> +		pinctrl-names = "default";
>>>>> +		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
>>>>> +		post-power-on-delay-ms = <200>;
>>>>> +	};
>>>>> +};
>>>>> +
>>>>> +&codec {
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&codec_analog {
>>>>> +	cpvdd-supply = <&reg_eldo1>;
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&cpu0 {
>>>>> +	cpu-supply = <&reg_dcdc2>;
>>>>> +};
>>>>> +
>>>>> +&cpu1 {
>>>>> +	cpu-supply = <&reg_dcdc2>;
>>>>> +};
>>>>> +
>>>>> +&cpu2 {
>>>>> +	cpu-supply = <&reg_dcdc2>;
>>>>> +};
>>>>> +
>>>>> +&cpu3 {
>>>>> +	cpu-supply = <&reg_dcdc2>;
>>>>> +};
>>>>> +
>>>>> +&dai {
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&de {
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&ehci0 {
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&ehci1 {
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&hdmi {
>>>>> +	hvcc-supply = <&reg_dldo1>;
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&hdmi_out {
>>>>> +	hdmi_out_con: endpoint {
>>>>> +		remote-endpoint = <&hdmi_con_in>;
>>>>> +	};
>>>>> +};
>>>>> +
>>>>> +/* Connects to the AC200 chip */
>>>>> +&i2c0 {
>>>>> +	pinctrl-names = "default";
>>>>> +	pinctrl-0 = <&i2c0_pins>;
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&i2c0_pins {
>>>>> +	bias-pull-up;
>>>>> +};
>>>>> +
>>>>> +&mmc0 {
>>>>> +	pinctrl-names = "default";
>>>>> +	pinctrl-0 = <&mmc0_pins>;
>>>>> +	vmmc-supply = <&reg_dcdc1>;
>>>>> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
>>>>> +	disable-wp;
>>>>> +	bus-width = <4>;
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&mmc1 {
>>>>> +	pinctrl-names = "default";
>>>>> +	pinctrl-0 = <&mmc1_pins>;
>>>>> +	vmmc-supply = <&reg_aldo1>;
>>>>> +	vqmmc-supply = <&reg_dldo4>;
>>>>> +	mmc-pwrseq = <&wifi_pwrseq>;
>>>>> +	bus-width = <4>;
>>>>> +	non-removable;
>>>>> +	status = "okay";
>>>>> +
>>>>> +	rtl8723bs: wifi@1 {
>>>>> +		reg = <1>;
>>>>> +		interrupt-parent = <&r_pio>;
>>>>> +		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
>>>>> +		interrupt-names = "host-wake";
>>>>> +	};
>>>>
>>>> Node without compatible doesn't help. Please remove it.
>>
>> Huh, but where do I put the the IRQ line then? And every other RTL8723BS
>> user seems to do the same?
> 
> It's good, sorry for the noise.

Just for the records, and for my own reference:
Since there is no "ranges" property in the MMC node, the Linux platform 
bus driver is not automatically traversing any child nodes. So we don't 
need a compatible string. Instead it's a new addressing scheme (this 
obsolete MMC "bus" address, like SPI or I2C), so it's up to the driver 
to do the child iteration. And it will match device #1 to reg <1>, and 
use that node, as Chen-Yu mentioned.

>>>>
>>>>> +};
>>>>> +
>>>>> +&mmc2 {
>>>>> +	pinctrl-names = "default";
>>>>> +	pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
>>>>> +	vmmc-supply = <&reg_dcdc1>;
>>>>> +	vqmmc-supply = <&reg_eldo1>;
>>>>> +	bus-width = <8>;
>>>>> +	non-removable;
>>>>> +	mmc-ddr-1_8v;
>>>>> +	mmc-hs200-1_8v;
>>>>
>>>> Aren't these speed modes enabled by default?
>>
>> Enabled by who? Our current sunxi-mmc driver? I cannot find anything in
>> the binding that suggests that there would be some default settings.
> 
> Looking at Linux sunxi mmc driver, mmc-ddr-1_8v is enabled by default for
> "new timings" variants except for H5. Anyway...

But this is a Linux implementation detail, which we should not rely on 
in a DT? And if I remember Maxime correctly back then, the plan was to 
avoid those driver hacks and just say what we support in the DT, going 
forward. This might be needed for other OSes, which might not support 
HS-200?
>>> Sorry, mmc-hs200-1_8v is ok, but mmc-ddr-1_8v should be
>>> removed.
>>
>> Mmh, I am confused: I thought after the H5 eMMC mishap we figured that
>> all speed modes supported by the eMMC chip should be listed in the DT?
> 
> I think H5 just has (had?) driver issue. From what I can see, only highest
> supported mode by kernel and chip is specified in all Allwinner DTs.
> mmc-ddr-1_8v is only specified by two recent board addition, where I missed
> it while reviewing.
> 
>> So any driver wouldn't need to make assumptions, and if a particular
>> mode shows problems on a board, we just remove that mode from the DT.
>> Actually, thinking about that, I guess I should list HS-400 as well? The
>> BSP kernel uses that mode.
> 
> Sure, but it also calibrates timing for it. If you'll specify HS400, kernel
> will try to use it, but it won't work.

But this is also a limitation of the current Linux kernel driver. And 
since we indeed don't support HS-400, we explicitly remove it from the 
capability list, *after* the call to mmc_of_parse():

drivers/mmc/host/sunxi-mmc.c:1460
         /* TODO: This driver doesn't support HS400 mode yet */
         mmc->caps2 &= ~MMC_CAP2_HS400;

So I think this should be safe?

Cheers,
Andre

> 
>> Or do you mean to say that in particular DDR (@1.8V) is problematic? I
>> cannot test at the moment, but could try later to force that mode.
> 
> No, no need.
> 
> Best regards,
> Jernej
> 
>>
>> Cheers,
>> Andre
>>
>>
>>>>> +	cap-mmc-hw-reset;
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&ohci0 {
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&ohci1 {
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&pio {
>>>>> +	vcc-pb-supply = <&reg_dcdc1>;
>>>>> +	vcc-pc-supply = <&reg_dcdc1>;
>>>>> +	vcc-pd-supply = <&reg_dcdc1>;
>>>>> +	vcc-pe-supply = <&reg_dcdc1>;
>>>>> +	vcc-pf-supply = <&reg_dcdc1>;
>>>>> +	vcc-pg-supply = <&reg_dldo4>;
>>>>> +	vcc-ph-supply = <&reg_dcdc1>;
>>>>> +};
>>>>> +
>>>>> +&r_ir {
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&r_pio {
>>>>> +	/*
>>>>> +	 * We cannot add that supply for now since it would create a circular
>>>>> +	 * dependency between pinctrl, the regulator and the RSB Bus.
>>>>> +	 *
>>>>> +	 * vcc-pl-supply = <&reg_aldo2>;
>>>>> +	 */
>>>>> +};
>>>>> +
>>>>> +&r_rsb {
>>>>> +	status = "okay";
>>>>> +
>>>>> +	axp803: pmic@3a3 {
>>>>> +		compatible = "x-powers,axp803";
>>>>> +		reg = <0x3a3>;
>>>>> +		interrupt-parent = <&r_intc>;
>>>>> +		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_LOW>;
>>>>> +		x-powers,drive-vbus-en;
>>>>> +
>>>>> +		vin1-supply = <&reg_vcc5v>;
>>>>> +		vin2-supply = <&reg_vcc5v>;
>>>>> +		vin3-supply = <&reg_vcc5v>;
>>>>> +		vin5-supply = <&reg_vcc5v>;
>>>>> +		vin6-supply = <&reg_vcc5v>;
>>>>> +		aldoin-supply = <&reg_vcc5v>;
>>>>> +		dldoin-supply = <&reg_vcc5v>;
>>>>> +		eldoin-supply = <&reg_vcc5v>;
>>>>> +		fldoin-supply = <&reg_vcc5v>;
>>>>> +		drivevbus-supply = <&reg_vcc5v>;
>>>>> +		ips-supply = <&reg_vcc5v>;
>>>>> +
>>>>> +		status = "okay";
>>>>> +	};
>>>>> +};
>>>>> +
>>>>> +#include "axp803.dtsi"
>>>>> +
>>>>> +&ac_power_supply {
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&reg_dcdc1 {
>>>>> +	regulator-always-on;
>>>>> +	regulator-min-microvolt = <3300000>;
>>>>> +	regulator-max-microvolt = <3300000>;
>>>>> +	regulator-name = "vcc-3v3";
>>>>> +};
>>>>> +
>>>>> +&reg_dcdc2 {
>>>>> +	regulator-always-on;
>>>>> +	regulator-min-microvolt = <1040000>;
>>>>> +	regulator-max-microvolt = <1300000>;
>>>>> +	regulator-name = "vdd-cpux";
>>>>> +};
>>>>> +
>>>>> +/* DCDC3 is polyphased with DCDC2 */
>>>>> +
>>>>> +&reg_dcdc5 {
>>>>> +	regulator-always-on;
>>>>> +	regulator-min-microvolt = <1500000>;
>>>>> +	regulator-max-microvolt = <1500000>;
>>>>> +	regulator-name = "vcc-dram";
>>>>> +};
>>>>> +
>>>>> +/* Deviates from the reset default of 1.1V. */
>>>>> +&reg_dcdc6 {
>>>>> +	regulator-always-on;
>>>>> +	regulator-min-microvolt = <1200000>;
>>>>> +	regulator-max-microvolt = <1200000>;
>>>>> +	regulator-name = "vdd-sys";
>>>>> +};
>>>>> +
>>>>> +&reg_aldo1 {
>>>>> +	regulator-min-microvolt = <3300000>;
>>>>> +	regulator-max-microvolt = <3300000>;
>>>>> +	regulator-name = "vcc-wifi";
>>>>> +};
>>>>> +
>>>>> +&reg_aldo2 {
>>>>> +	/* Specifying R_PIO consumer would create circular dependency. */
>>>>> +	regulator-always-on;
>>>>> +	regulator-min-microvolt = <3300000>;
>>>>> +	regulator-max-microvolt = <3300000>;
>>>>> +	regulator-name = "vcc-pl";
>>>>> +};
>>>>> +
>>>>> +&reg_aldo3 {
>>>>> +	regulator-always-on;
>>>>> +	regulator-min-microvolt = <3000000>;
>>>>> +	regulator-max-microvolt = <3000000>;
>>>>> +	regulator-name = "vcc-pll-avcc";
>>>>> +};
>>>>> +
>>>>> +/* AC200 power supply */
>>>>> +&reg_dldo1 {
>>>>> +	regulator-always-on;
>>>>> +	regulator-min-microvolt = <3300000>;
>>>>> +	regulator-max-microvolt = <3300000>;
>>>>> +	regulator-name = "vcc-ave-33";
>>>>> +};
>>>>> +
>>>>> +&reg_dldo4 {
>>>>> +	regulator-min-microvolt = <3300000>;
>>>>> +	regulator-max-microvolt = <3300000>;
>>>>> +	regulator-name = "vcc-wifi-io";
>>>>> +};
>>>>> +
>>>>> +&reg_drivevbus {
>>>>> +	regulator-name = "usb0-vbus";
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&reg_eldo1 {
>>>>> +	regulator-always-on;
>>>>> +	regulator-min-microvolt = <1800000>;
>>>>> +	regulator-max-microvolt = <1800000>;
>>>>> +	regulator-name = "vcc-cpvdd-dram-emmc";
>>>>> +};
>>>>> +
>>>>> +/* Supplies the arisc management core, needed by TF-A to power off cores. */
>>>>> +&reg_fldo2 {
>>>>> +	regulator-always-on;
>>>>> +	regulator-min-microvolt = <1100000>;
>>>>> +	regulator-max-microvolt = <1100000>;
>>>>> +	regulator-name = "vdd-cpus";
>>>>> +};
>>>>> +
>>>>> +&reg_rtc_ldo {
>>>>> +	regulator-name = "vcc-rtc";
>>>>> +};
>>>>> +
>>>>> +&simplefb_hdmi {
>>>>> +	vcc-hdmi-supply = <&reg_dcdc1>;
>>>>> +};
>>>>> +
>>>>> +&sound {
>>>>> +	simple-audio-card,aux-devs = <&codec_analog>;
>>>>> +	simple-audio-card,widgets = "Microphone", "Microphone Jack",
>>>>> +				    "Headphone", "Headphone Jack";
>>>>> +	simple-audio-card,routing =
>>>>> +			"Left DAC", "DACL",
>>>>> +			"Right DAC", "DACR",
>>>>> +			"Headphone Jack", "HP",
>>>>> +			"ADCL", "Left ADC",
>>>>> +			"ADCR", "Right ADC",
>>>>> +			"MIC2", "Microphone Jack";
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +/* On the (unpopulated) UART pads. */
>>>>> +&uart0 {
>>>>> +	pinctrl-names = "default";
>>>>> +	pinctrl-0 = <&uart0_pb_pins>;
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&uart1 {
>>>>> +	pinctrl-names = "default";
>>>>> +	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
>>>>> +	uart-has-rtscts;
>>>>> +	status = "okay";
>>>>> +
>>>>> +	bluetooth {
>>>>> +		compatible = "realtek,rtl8723bs-bt";
>>>>> +		enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
>>>>> +		max-speed = <1500000>;
>>>>> +	};
>>>>> +};
>>>>> +
>>>>> +&usb_otg {
>>>>> +	dr_mode = "host";
>>>>> +	status = "okay";
>>>>> +};
>>>>> +
>>>>> +&usbphy {
>>>>> +	usb0_vbus-supply = <&reg_drivevbus>;
>>>>> +	usb1_vbus-supply = <&reg_drivevbus>;
>>>>> +	status = "okay";
>>>>> +};
>>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>
>>>
>>>
>>>
>>
> 
> 
> 
>

Jernej Škrabec Feb. 6, 2024, 6:23 p.m. UTC | #6

Dne torek, 06. februar 2024 ob 19:13:46 CET je Andre Przywara napisal(a):
> Hi Jernej,
> 
> On 06/02/2024 18:32, Jernej Škrabec wrote:
> > Dne torek, 06. februar 2024 ob 01:47:05 CET je Andre Przywara napisal(a):
> >> Hi Jernej,
> >>
> >> thanks for having a look!
> >>
> >> On 05/02/2024 19:20, Jernej Škrabec wrote:
> >>> Dne ponedeljek, 05. februar 2024 ob 19:12:45 CET je Jernej Škrabec napisal(a):
> >>>> Hi Andre!
> >>>>
> >>>> Dne nedelja, 04. februar 2024 ob 10:44:04 CET je Andre Przywara napisal(a):
> >>>>> The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
> >>>>> which appears to be just a relabelled A64. It was launched in 2015 by
> >>>>> the now defunct company Jide, and shipped with a desktop optimised
> >>>>> version of Android. It features
> >>>>> 	- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
> >>>>> 	- 1 or 2 GB DRAM
> >>>>> 	- 8 or 16 GB eMMC flash
> >>>>> 	- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
> >>>>> 	- RTL8723BS WiFi & Bluetooth chip
> >>>>> 	- HDMI port
> >>>>> 	- two USB 2.0 ports
> >>>>> 	- 3.5mm AV port
> >>>>> 	- microSD card slot
> >>>>>
> >>>>> The devicetree covers most peripherals, though there is no agreed
> >>>>> binding for the PHY chip yet, so this is left out.
> >>>>>
> >>>>> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> >>>>> ---
> >>>>>    arch/arm64/boot/dts/allwinner/Makefile        |   1 +
> >>>>>    .../allwinner/sun50i-h64-remix-mini-pc.dts    | 357 ++++++++++++++++++
> >>>>>    2 files changed, 358 insertions(+)
> >>>>>    create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> >>>>>
> >>>>> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> >>>>> index 91d505b385de..2db3b15ad09f 100644
> >>>>> --- a/arch/arm64/boot/dts/allwinner/Makefile
> >>>>> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> >>>>> @@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
> >>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab-early-adopter.dtb
> >>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
> >>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
> >>>>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h64-remix-mini-pc.dtb
> >>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb
> >>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
> >>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
> >>>>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> >>>>> new file mode 100644
> >>>>> index 000000000000..537923a541a8
> >>>>> --- /dev/null
> >>>>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> >>>>> @@ -0,0 +1,357 @@
> >>>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> >>>>> +// Copyright (c) 2018 ARM Ltd.
> >>>>
> >>>> Shouldn't be 2024?
> >>
> >> Well, that just documents that sad fact that I indeed created this file
> >> 6 years ago, but just managed now to actually send this. Is there a
> >> requirement for this being "recent"?
> > 
> > Not really, but it's strange looking. Some might incorrectly assume that it's
> > present in the kernel longer than it really is.
> 
> OK, I will put in 2023, as this is when I touched this again.
> 
> >>>>
> >>>>> +
> >>>>> +/dts-v1/;
> >>>>> +
> >>>>> +#include "sun50i-a64.dtsi"
> >>>>> +#include "sun50i-a64-cpu-opp.dtsi"
> >>>>> +
> >>>>> +#include <dt-bindings/gpio/gpio.h>
> >>>>> +
> >>>>> +/ {
> >>>>> +	model = "Remix Mini PC";
> >>>>> +	compatible = "jide,remix-mini-pc", "allwinner,sun50i-h64",
> >>>>> +		     "allwinner,sun50i-a64";
> >>>>> +
> >>>>> +	aliases {
> >>>>> +		ethernet1 = &rtl8723bs;
> >>>>> +		serial0 = &uart0;
> >>>>> +	};
> >>>>> +
> >>>>> +	chosen {
> >>>>> +		stdout-path = "serial0:115200n8";
> >>>>> +	};
> >>>>> +
> >>>>> +	hdmi-connector {
> >>>>> +		compatible = "hdmi-connector";
> >>>>> +		type = "a";
> >>>>> +
> >>>>> +		port {
> >>>>> +			hdmi_con_in: endpoint {
> >>>>> +				remote-endpoint = <&hdmi_out_con>;
> >>>>> +			};
> >>>>> +		};
> >>>>> +	};
> >>>>> +
> >>>>> +	reg_vcc5v: regulator-5v {
> >>>>> +		/* board wide 5V supply directly from the DC input */
> >>>>> +		compatible = "regulator-fixed";
> >>>>> +		regulator-name = "vcc-5v";
> >>>>> +		regulator-min-microvolt = <5000000>;
> >>>>> +		regulator-max-microvolt = <5000000>;
> >>>>> +		regulator-always-on;
> >>>>> +	};
> >>>>> +
> >>>>> +	wifi_pwrseq: wifi_pwrseq {
> >>>>> +		compatible = "mmc-pwrseq-simple";
> >>>>> +		pinctrl-names = "default";
> >>>>> +		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
> >>>>> +		post-power-on-delay-ms = <200>;
> >>>>> +	};
> >>>>> +};
> >>>>> +
> >>>>> +&codec {
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&codec_analog {
> >>>>> +	cpvdd-supply = <&reg_eldo1>;
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&cpu0 {
> >>>>> +	cpu-supply = <&reg_dcdc2>;
> >>>>> +};
> >>>>> +
> >>>>> +&cpu1 {
> >>>>> +	cpu-supply = <&reg_dcdc2>;
> >>>>> +};
> >>>>> +
> >>>>> +&cpu2 {
> >>>>> +	cpu-supply = <&reg_dcdc2>;
> >>>>> +};
> >>>>> +
> >>>>> +&cpu3 {
> >>>>> +	cpu-supply = <&reg_dcdc2>;
> >>>>> +};
> >>>>> +
> >>>>> +&dai {
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&de {
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&ehci0 {
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&ehci1 {
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&hdmi {
> >>>>> +	hvcc-supply = <&reg_dldo1>;
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&hdmi_out {
> >>>>> +	hdmi_out_con: endpoint {
> >>>>> +		remote-endpoint = <&hdmi_con_in>;
> >>>>> +	};
> >>>>> +};
> >>>>> +
> >>>>> +/* Connects to the AC200 chip */
> >>>>> +&i2c0 {
> >>>>> +	pinctrl-names = "default";
> >>>>> +	pinctrl-0 = <&i2c0_pins>;
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&i2c0_pins {
> >>>>> +	bias-pull-up;
> >>>>> +};
> >>>>> +
> >>>>> +&mmc0 {
> >>>>> +	pinctrl-names = "default";
> >>>>> +	pinctrl-0 = <&mmc0_pins>;
> >>>>> +	vmmc-supply = <&reg_dcdc1>;
> >>>>> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> >>>>> +	disable-wp;
> >>>>> +	bus-width = <4>;
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&mmc1 {
> >>>>> +	pinctrl-names = "default";
> >>>>> +	pinctrl-0 = <&mmc1_pins>;
> >>>>> +	vmmc-supply = <&reg_aldo1>;
> >>>>> +	vqmmc-supply = <&reg_dldo4>;
> >>>>> +	mmc-pwrseq = <&wifi_pwrseq>;
> >>>>> +	bus-width = <4>;
> >>>>> +	non-removable;
> >>>>> +	status = "okay";
> >>>>> +
> >>>>> +	rtl8723bs: wifi@1 {
> >>>>> +		reg = <1>;
> >>>>> +		interrupt-parent = <&r_pio>;
> >>>>> +		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
> >>>>> +		interrupt-names = "host-wake";
> >>>>> +	};
> >>>>
> >>>> Node without compatible doesn't help. Please remove it.
> >>
> >> Huh, but where do I put the the IRQ line then? And every other RTL8723BS
> >> user seems to do the same?
> > 
> > It's good, sorry for the noise.
> 
> Just for the records, and for my own reference:
> Since there is no "ranges" property in the MMC node, the Linux platform 
> bus driver is not automatically traversing any child nodes. So we don't 
> need a compatible string. Instead it's a new addressing scheme (this 
> obsolete MMC "bus" address, like SPI or I2C), so it's up to the driver 
> to do the child iteration. And it will match device #1 to reg <1>, and 
> use that node, as Chen-Yu mentioned.
> 
> >>>>
> >>>>> +};
> >>>>> +
> >>>>> +&mmc2 {
> >>>>> +	pinctrl-names = "default";
> >>>>> +	pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
> >>>>> +	vmmc-supply = <&reg_dcdc1>;
> >>>>> +	vqmmc-supply = <&reg_eldo1>;
> >>>>> +	bus-width = <8>;
> >>>>> +	non-removable;
> >>>>> +	mmc-ddr-1_8v;
> >>>>> +	mmc-hs200-1_8v;
> >>>>
> >>>> Aren't these speed modes enabled by default?
> >>
> >> Enabled by who? Our current sunxi-mmc driver? I cannot find anything in
> >> the binding that suggests that there would be some default settings.
> > 
> > Looking at Linux sunxi mmc driver, mmc-ddr-1_8v is enabled by default for
> > "new timings" variants except for H5. Anyway...
> 
> But this is a Linux implementation detail, which we should not rely on 
> in a DT? And if I remember Maxime correctly back then, the plan was to 
> avoid those driver hacks and just say what we support in the DT, going 
> forward. This might be needed for other OSes, which might not support 
> HS-200?
> >>> Sorry, mmc-hs200-1_8v is ok, but mmc-ddr-1_8v should be
> >>> removed.
> >>
> >> Mmh, I am confused: I thought after the H5 eMMC mishap we figured that
> >> all speed modes supported by the eMMC chip should be listed in the DT?
> > 
> > I think H5 just has (had?) driver issue. From what I can see, only highest
> > supported mode by kernel and chip is specified in all Allwinner DTs.
> > mmc-ddr-1_8v is only specified by two recent board addition, where I missed
> > it while reviewing.
> > 
> >> So any driver wouldn't need to make assumptions, and if a particular
> >> mode shows problems on a board, we just remove that mode from the DT.
> >> Actually, thinking about that, I guess I should list HS-400 as well? The
> >> BSP kernel uses that mode.
> > 
> > Sure, but it also calibrates timing for it. If you'll specify HS400, kernel
> > will try to use it, but it won't work.
> 
> But this is also a limitation of the current Linux kernel driver. And 
> since we indeed don't support HS-400, we explicitly remove it from the 
> capability list, *after* the call to mmc_of_parse():
> 
> drivers/mmc/host/sunxi-mmc.c:1460
>          /* TODO: This driver doesn't support HS400 mode yet */
>          mmc->caps2 &= ~MMC_CAP2_HS400;
> 
> So I think this should be safe?

Right. Can you test it?

Best regards,
Jernej

> 
> Cheers,
> Andre
> 
> > 
> >> Or do you mean to say that in particular DDR (@1.8V) is problematic? I
> >> cannot test at the moment, but could try later to force that mode.
> > 
> > No, no need.
> > 
> > Best regards,
> > Jernej
> > 
> >>
> >> Cheers,
> >> Andre
> >>
> >>
> >>>>> +	cap-mmc-hw-reset;
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&ohci0 {
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&ohci1 {
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&pio {
> >>>>> +	vcc-pb-supply = <&reg_dcdc1>;
> >>>>> +	vcc-pc-supply = <&reg_dcdc1>;
> >>>>> +	vcc-pd-supply = <&reg_dcdc1>;
> >>>>> +	vcc-pe-supply = <&reg_dcdc1>;
> >>>>> +	vcc-pf-supply = <&reg_dcdc1>;
> >>>>> +	vcc-pg-supply = <&reg_dldo4>;
> >>>>> +	vcc-ph-supply = <&reg_dcdc1>;
> >>>>> +};
> >>>>> +
> >>>>> +&r_ir {
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&r_pio {
> >>>>> +	/*
> >>>>> +	 * We cannot add that supply for now since it would create a circular
> >>>>> +	 * dependency between pinctrl, the regulator and the RSB Bus.
> >>>>> +	 *
> >>>>> +	 * vcc-pl-supply = <&reg_aldo2>;
> >>>>> +	 */
> >>>>> +};
> >>>>> +
> >>>>> +&r_rsb {
> >>>>> +	status = "okay";
> >>>>> +
> >>>>> +	axp803: pmic@3a3 {
> >>>>> +		compatible = "x-powers,axp803";
> >>>>> +		reg = <0x3a3>;
> >>>>> +		interrupt-parent = <&r_intc>;
> >>>>> +		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_LOW>;
> >>>>> +		x-powers,drive-vbus-en;
> >>>>> +
> >>>>> +		vin1-supply = <&reg_vcc5v>;
> >>>>> +		vin2-supply = <&reg_vcc5v>;
> >>>>> +		vin3-supply = <&reg_vcc5v>;
> >>>>> +		vin5-supply = <&reg_vcc5v>;
> >>>>> +		vin6-supply = <&reg_vcc5v>;
> >>>>> +		aldoin-supply = <&reg_vcc5v>;
> >>>>> +		dldoin-supply = <&reg_vcc5v>;
> >>>>> +		eldoin-supply = <&reg_vcc5v>;
> >>>>> +		fldoin-supply = <&reg_vcc5v>;
> >>>>> +		drivevbus-supply = <&reg_vcc5v>;
> >>>>> +		ips-supply = <&reg_vcc5v>;
> >>>>> +
> >>>>> +		status = "okay";
> >>>>> +	};
> >>>>> +};
> >>>>> +
> >>>>> +#include "axp803.dtsi"
> >>>>> +
> >>>>> +&ac_power_supply {
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&reg_dcdc1 {
> >>>>> +	regulator-always-on;
> >>>>> +	regulator-min-microvolt = <3300000>;
> >>>>> +	regulator-max-microvolt = <3300000>;
> >>>>> +	regulator-name = "vcc-3v3";
> >>>>> +};
> >>>>> +
> >>>>> +&reg_dcdc2 {
> >>>>> +	regulator-always-on;
> >>>>> +	regulator-min-microvolt = <1040000>;
> >>>>> +	regulator-max-microvolt = <1300000>;
> >>>>> +	regulator-name = "vdd-cpux";
> >>>>> +};
> >>>>> +
> >>>>> +/* DCDC3 is polyphased with DCDC2 */
> >>>>> +
> >>>>> +&reg_dcdc5 {
> >>>>> +	regulator-always-on;
> >>>>> +	regulator-min-microvolt = <1500000>;
> >>>>> +	regulator-max-microvolt = <1500000>;
> >>>>> +	regulator-name = "vcc-dram";
> >>>>> +};
> >>>>> +
> >>>>> +/* Deviates from the reset default of 1.1V. */
> >>>>> +&reg_dcdc6 {
> >>>>> +	regulator-always-on;
> >>>>> +	regulator-min-microvolt = <1200000>;
> >>>>> +	regulator-max-microvolt = <1200000>;
> >>>>> +	regulator-name = "vdd-sys";
> >>>>> +};
> >>>>> +
> >>>>> +&reg_aldo1 {
> >>>>> +	regulator-min-microvolt = <3300000>;
> >>>>> +	regulator-max-microvolt = <3300000>;
> >>>>> +	regulator-name = "vcc-wifi";
> >>>>> +};
> >>>>> +
> >>>>> +&reg_aldo2 {
> >>>>> +	/* Specifying R_PIO consumer would create circular dependency. */
> >>>>> +	regulator-always-on;
> >>>>> +	regulator-min-microvolt = <3300000>;
> >>>>> +	regulator-max-microvolt = <3300000>;
> >>>>> +	regulator-name = "vcc-pl";
> >>>>> +};
> >>>>> +
> >>>>> +&reg_aldo3 {
> >>>>> +	regulator-always-on;
> >>>>> +	regulator-min-microvolt = <3000000>;
> >>>>> +	regulator-max-microvolt = <3000000>;
> >>>>> +	regulator-name = "vcc-pll-avcc";
> >>>>> +};
> >>>>> +
> >>>>> +/* AC200 power supply */
> >>>>> +&reg_dldo1 {
> >>>>> +	regulator-always-on;
> >>>>> +	regulator-min-microvolt = <3300000>;
> >>>>> +	regulator-max-microvolt = <3300000>;
> >>>>> +	regulator-name = "vcc-ave-33";
> >>>>> +};
> >>>>> +
> >>>>> +&reg_dldo4 {
> >>>>> +	regulator-min-microvolt = <3300000>;
> >>>>> +	regulator-max-microvolt = <3300000>;
> >>>>> +	regulator-name = "vcc-wifi-io";
> >>>>> +};
> >>>>> +
> >>>>> +&reg_drivevbus {
> >>>>> +	regulator-name = "usb0-vbus";
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&reg_eldo1 {
> >>>>> +	regulator-always-on;
> >>>>> +	regulator-min-microvolt = <1800000>;
> >>>>> +	regulator-max-microvolt = <1800000>;
> >>>>> +	regulator-name = "vcc-cpvdd-dram-emmc";
> >>>>> +};
> >>>>> +
> >>>>> +/* Supplies the arisc management core, needed by TF-A to power off cores. */
> >>>>> +&reg_fldo2 {
> >>>>> +	regulator-always-on;
> >>>>> +	regulator-min-microvolt = <1100000>;
> >>>>> +	regulator-max-microvolt = <1100000>;
> >>>>> +	regulator-name = "vdd-cpus";
> >>>>> +};
> >>>>> +
> >>>>> +&reg_rtc_ldo {
> >>>>> +	regulator-name = "vcc-rtc";
> >>>>> +};
> >>>>> +
> >>>>> +&simplefb_hdmi {
> >>>>> +	vcc-hdmi-supply = <&reg_dcdc1>;
> >>>>> +};
> >>>>> +
> >>>>> +&sound {
> >>>>> +	simple-audio-card,aux-devs = <&codec_analog>;
> >>>>> +	simple-audio-card,widgets = "Microphone", "Microphone Jack",
> >>>>> +				    "Headphone", "Headphone Jack";
> >>>>> +	simple-audio-card,routing =
> >>>>> +			"Left DAC", "DACL",
> >>>>> +			"Right DAC", "DACR",
> >>>>> +			"Headphone Jack", "HP",
> >>>>> +			"ADCL", "Left ADC",
> >>>>> +			"ADCR", "Right ADC",
> >>>>> +			"MIC2", "Microphone Jack";
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +/* On the (unpopulated) UART pads. */
> >>>>> +&uart0 {
> >>>>> +	pinctrl-names = "default";
> >>>>> +	pinctrl-0 = <&uart0_pb_pins>;
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&uart1 {
> >>>>> +	pinctrl-names = "default";
> >>>>> +	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> >>>>> +	uart-has-rtscts;
> >>>>> +	status = "okay";
> >>>>> +
> >>>>> +	bluetooth {
> >>>>> +		compatible = "realtek,rtl8723bs-bt";
> >>>>> +		enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> >>>>> +		max-speed = <1500000>;
> >>>>> +	};
> >>>>> +};
> >>>>> +
> >>>>> +&usb_otg {
> >>>>> +	dr_mode = "host";
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>> +
> >>>>> +&usbphy {
> >>>>> +	usb0_vbus-supply = <&reg_drivevbus>;
> >>>>> +	usb1_vbus-supply = <&reg_drivevbus>;
> >>>>> +	status = "okay";
> >>>>> +};
> >>>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>
> >>>
> >>>
> >>>
> >>
> > 
> > 
> > 
> > 
>

Jernej Škrabec Feb. 6, 2024, 6:27 p.m. UTC | #7

Dne torek, 06. februar 2024 ob 19:23:35 CET je Jernej Škrabec napisal(a):
> Dne torek, 06. februar 2024 ob 19:13:46 CET je Andre Przywara napisal(a):
> > Hi Jernej,
> > 
> > On 06/02/2024 18:32, Jernej Škrabec wrote:
> > > Dne torek, 06. februar 2024 ob 01:47:05 CET je Andre Przywara napisal(a):
> > >> Hi Jernej,
> > >>
> > >> thanks for having a look!
> > >>
> > >> On 05/02/2024 19:20, Jernej Škrabec wrote:
> > >>> Dne ponedeljek, 05. februar 2024 ob 19:12:45 CET je Jernej Škrabec napisal(a):
> > >>>> Hi Andre!
> > >>>>
> > >>>> Dne nedelja, 04. februar 2024 ob 10:44:04 CET je Andre Przywara napisal(a):
> > >>>>> The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
> > >>>>> which appears to be just a relabelled A64. It was launched in 2015 by
> > >>>>> the now defunct company Jide, and shipped with a desktop optimised
> > >>>>> version of Android. It features
> > >>>>> 	- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
> > >>>>> 	- 1 or 2 GB DRAM
> > >>>>> 	- 8 or 16 GB eMMC flash
> > >>>>> 	- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
> > >>>>> 	- RTL8723BS WiFi & Bluetooth chip
> > >>>>> 	- HDMI port
> > >>>>> 	- two USB 2.0 ports
> > >>>>> 	- 3.5mm AV port
> > >>>>> 	- microSD card slot
> > >>>>>
> > >>>>> The devicetree covers most peripherals, though there is no agreed
> > >>>>> binding for the PHY chip yet, so this is left out.
> > >>>>>
> > >>>>> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> > >>>>> ---
> > >>>>>    arch/arm64/boot/dts/allwinner/Makefile        |   1 +
> > >>>>>    .../allwinner/sun50i-h64-remix-mini-pc.dts    | 357 ++++++++++++++++++
> > >>>>>    2 files changed, 358 insertions(+)
> > >>>>>    create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> > >>>>>
> > >>>>> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> > >>>>> index 91d505b385de..2db3b15ad09f 100644
> > >>>>> --- a/arch/arm64/boot/dts/allwinner/Makefile
> > >>>>> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> > >>>>> @@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
> > >>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab-early-adopter.dtb
> > >>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
> > >>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
> > >>>>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h64-remix-mini-pc.dtb
> > >>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb
> > >>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
> > >>>>>    dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
> > >>>>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> > >>>>> new file mode 100644
> > >>>>> index 000000000000..537923a541a8
> > >>>>> --- /dev/null
> > >>>>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
> > >>>>> @@ -0,0 +1,357 @@
> > >>>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > >>>>> +// Copyright (c) 2018 ARM Ltd.
> > >>>>
> > >>>> Shouldn't be 2024?
> > >>
> > >> Well, that just documents that sad fact that I indeed created this file
> > >> 6 years ago, but just managed now to actually send this. Is there a
> > >> requirement for this being "recent"?
> > > 
> > > Not really, but it's strange looking. Some might incorrectly assume that it's
> > > present in the kernel longer than it really is.
> > 
> > OK, I will put in 2023, as this is when I touched this again.
> > 
> > >>>>
> > >>>>> +
> > >>>>> +/dts-v1/;
> > >>>>> +
> > >>>>> +#include "sun50i-a64.dtsi"
> > >>>>> +#include "sun50i-a64-cpu-opp.dtsi"
> > >>>>> +
> > >>>>> +#include <dt-bindings/gpio/gpio.h>
> > >>>>> +
> > >>>>> +/ {
> > >>>>> +	model = "Remix Mini PC";
> > >>>>> +	compatible = "jide,remix-mini-pc", "allwinner,sun50i-h64",
> > >>>>> +		     "allwinner,sun50i-a64";
> > >>>>> +
> > >>>>> +	aliases {
> > >>>>> +		ethernet1 = &rtl8723bs;
> > >>>>> +		serial0 = &uart0;
> > >>>>> +	};
> > >>>>> +
> > >>>>> +	chosen {
> > >>>>> +		stdout-path = "serial0:115200n8";
> > >>>>> +	};
> > >>>>> +
> > >>>>> +	hdmi-connector {
> > >>>>> +		compatible = "hdmi-connector";
> > >>>>> +		type = "a";
> > >>>>> +
> > >>>>> +		port {
> > >>>>> +			hdmi_con_in: endpoint {
> > >>>>> +				remote-endpoint = <&hdmi_out_con>;
> > >>>>> +			};
> > >>>>> +		};
> > >>>>> +	};
> > >>>>> +
> > >>>>> +	reg_vcc5v: regulator-5v {
> > >>>>> +		/* board wide 5V supply directly from the DC input */
> > >>>>> +		compatible = "regulator-fixed";
> > >>>>> +		regulator-name = "vcc-5v";
> > >>>>> +		regulator-min-microvolt = <5000000>;
> > >>>>> +		regulator-max-microvolt = <5000000>;
> > >>>>> +		regulator-always-on;
> > >>>>> +	};
> > >>>>> +
> > >>>>> +	wifi_pwrseq: wifi_pwrseq {
> > >>>>> +		compatible = "mmc-pwrseq-simple";
> > >>>>> +		pinctrl-names = "default";
> > >>>>> +		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
> > >>>>> +		post-power-on-delay-ms = <200>;
> > >>>>> +	};
> > >>>>> +};
> > >>>>> +
> > >>>>> +&codec {
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&codec_analog {
> > >>>>> +	cpvdd-supply = <&reg_eldo1>;
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&cpu0 {
> > >>>>> +	cpu-supply = <&reg_dcdc2>;
> > >>>>> +};
> > >>>>> +
> > >>>>> +&cpu1 {
> > >>>>> +	cpu-supply = <&reg_dcdc2>;
> > >>>>> +};
> > >>>>> +
> > >>>>> +&cpu2 {
> > >>>>> +	cpu-supply = <&reg_dcdc2>;
> > >>>>> +};
> > >>>>> +
> > >>>>> +&cpu3 {
> > >>>>> +	cpu-supply = <&reg_dcdc2>;
> > >>>>> +};
> > >>>>> +
> > >>>>> +&dai {
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&de {
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&ehci0 {
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&ehci1 {
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&hdmi {
> > >>>>> +	hvcc-supply = <&reg_dldo1>;
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&hdmi_out {
> > >>>>> +	hdmi_out_con: endpoint {
> > >>>>> +		remote-endpoint = <&hdmi_con_in>;
> > >>>>> +	};
> > >>>>> +};
> > >>>>> +
> > >>>>> +/* Connects to the AC200 chip */
> > >>>>> +&i2c0 {
> > >>>>> +	pinctrl-names = "default";
> > >>>>> +	pinctrl-0 = <&i2c0_pins>;
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&i2c0_pins {
> > >>>>> +	bias-pull-up;
> > >>>>> +};
> > >>>>> +
> > >>>>> +&mmc0 {
> > >>>>> +	pinctrl-names = "default";
> > >>>>> +	pinctrl-0 = <&mmc0_pins>;
> > >>>>> +	vmmc-supply = <&reg_dcdc1>;
> > >>>>> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> > >>>>> +	disable-wp;
> > >>>>> +	bus-width = <4>;
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&mmc1 {
> > >>>>> +	pinctrl-names = "default";
> > >>>>> +	pinctrl-0 = <&mmc1_pins>;
> > >>>>> +	vmmc-supply = <&reg_aldo1>;
> > >>>>> +	vqmmc-supply = <&reg_dldo4>;
> > >>>>> +	mmc-pwrseq = <&wifi_pwrseq>;
> > >>>>> +	bus-width = <4>;
> > >>>>> +	non-removable;
> > >>>>> +	status = "okay";
> > >>>>> +
> > >>>>> +	rtl8723bs: wifi@1 {
> > >>>>> +		reg = <1>;
> > >>>>> +		interrupt-parent = <&r_pio>;
> > >>>>> +		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
> > >>>>> +		interrupt-names = "host-wake";
> > >>>>> +	};
> > >>>>
> > >>>> Node without compatible doesn't help. Please remove it.
> > >>
> > >> Huh, but where do I put the the IRQ line then? And every other RTL8723BS
> > >> user seems to do the same?
> > > 
> > > It's good, sorry for the noise.
> > 
> > Just for the records, and for my own reference:
> > Since there is no "ranges" property in the MMC node, the Linux platform 
> > bus driver is not automatically traversing any child nodes. So we don't 
> > need a compatible string. Instead it's a new addressing scheme (this 
> > obsolete MMC "bus" address, like SPI or I2C), so it's up to the driver 
> > to do the child iteration. And it will match device #1 to reg <1>, and 
> > use that node, as Chen-Yu mentioned.
> > 
> > >>>>
> > >>>>> +};
> > >>>>> +
> > >>>>> +&mmc2 {
> > >>>>> +	pinctrl-names = "default";
> > >>>>> +	pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
> > >>>>> +	vmmc-supply = <&reg_dcdc1>;
> > >>>>> +	vqmmc-supply = <&reg_eldo1>;
> > >>>>> +	bus-width = <8>;
> > >>>>> +	non-removable;
> > >>>>> +	mmc-ddr-1_8v;
> > >>>>> +	mmc-hs200-1_8v;
> > >>>>
> > >>>> Aren't these speed modes enabled by default?
> > >>
> > >> Enabled by who? Our current sunxi-mmc driver? I cannot find anything in
> > >> the binding that suggests that there would be some default settings.
> > > 
> > > Looking at Linux sunxi mmc driver, mmc-ddr-1_8v is enabled by default for
> > > "new timings" variants except for H5. Anyway...
> > 
> > But this is a Linux implementation detail, which we should not rely on 
> > in a DT? And if I remember Maxime correctly back then, the plan was to 
> > avoid those driver hacks and just say what we support in the DT, going 
> > forward. This might be needed for other OSes, which might not support 
> > HS-200?
> > >>> Sorry, mmc-hs200-1_8v is ok, but mmc-ddr-1_8v should be
> > >>> removed.
> > >>
> > >> Mmh, I am confused: I thought after the H5 eMMC mishap we figured that
> > >> all speed modes supported by the eMMC chip should be listed in the DT?
> > > 
> > > I think H5 just has (had?) driver issue. From what I can see, only highest
> > > supported mode by kernel and chip is specified in all Allwinner DTs.
> > > mmc-ddr-1_8v is only specified by two recent board addition, where I missed
> > > it while reviewing.
> > > 
> > >> So any driver wouldn't need to make assumptions, and if a particular
> > >> mode shows problems on a board, we just remove that mode from the DT.
> > >> Actually, thinking about that, I guess I should list HS-400 as well? The
> > >> BSP kernel uses that mode.
> > > 
> > > Sure, but it also calibrates timing for it. If you'll specify HS400, kernel
> > > will try to use it, but it won't work.
> > 
> > But this is also a limitation of the current Linux kernel driver. And 
> > since we indeed don't support HS-400, we explicitly remove it from the 
> > capability list, *after* the call to mmc_of_parse():
> > 
> > drivers/mmc/host/sunxi-mmc.c:1460
> >          /* TODO: This driver doesn't support HS400 mode yet */
> >          mmc->caps2 &= ~MMC_CAP2_HS400;
> > 
> > So I think this should be safe?
> 
> Right. Can you test it?
> 
> Best regards,
> Jernej
> 
> > 
> > Cheers,
> > Andre
> > 
> > > 
> > >> Or do you mean to say that in particular DDR (@1.8V) is problematic? I
> > >> cannot test at the moment, but could try later to force that mode.
> > > 
> > > No, no need.

If we go in new direction, then it would be good to test it.

Best regards,
Jernej

> > > 
> > > Best regards,
> > > Jernej
> > > 
> > >>
> > >> Cheers,
> > >> Andre
> > >>
> > >>
> > >>>>> +	cap-mmc-hw-reset;
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&ohci0 {
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&ohci1 {
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&pio {
> > >>>>> +	vcc-pb-supply = <&reg_dcdc1>;
> > >>>>> +	vcc-pc-supply = <&reg_dcdc1>;
> > >>>>> +	vcc-pd-supply = <&reg_dcdc1>;
> > >>>>> +	vcc-pe-supply = <&reg_dcdc1>;
> > >>>>> +	vcc-pf-supply = <&reg_dcdc1>;
> > >>>>> +	vcc-pg-supply = <&reg_dldo4>;
> > >>>>> +	vcc-ph-supply = <&reg_dcdc1>;
> > >>>>> +};
> > >>>>> +
> > >>>>> +&r_ir {
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&r_pio {
> > >>>>> +	/*
> > >>>>> +	 * We cannot add that supply for now since it would create a circular
> > >>>>> +	 * dependency between pinctrl, the regulator and the RSB Bus.
> > >>>>> +	 *
> > >>>>> +	 * vcc-pl-supply = <&reg_aldo2>;
> > >>>>> +	 */
> > >>>>> +};
> > >>>>> +
> > >>>>> +&r_rsb {
> > >>>>> +	status = "okay";
> > >>>>> +
> > >>>>> +	axp803: pmic@3a3 {
> > >>>>> +		compatible = "x-powers,axp803";
> > >>>>> +		reg = <0x3a3>;
> > >>>>> +		interrupt-parent = <&r_intc>;
> > >>>>> +		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_LOW>;
> > >>>>> +		x-powers,drive-vbus-en;
> > >>>>> +
> > >>>>> +		vin1-supply = <&reg_vcc5v>;
> > >>>>> +		vin2-supply = <&reg_vcc5v>;
> > >>>>> +		vin3-supply = <&reg_vcc5v>;
> > >>>>> +		vin5-supply = <&reg_vcc5v>;
> > >>>>> +		vin6-supply = <&reg_vcc5v>;
> > >>>>> +		aldoin-supply = <&reg_vcc5v>;
> > >>>>> +		dldoin-supply = <&reg_vcc5v>;
> > >>>>> +		eldoin-supply = <&reg_vcc5v>;
> > >>>>> +		fldoin-supply = <&reg_vcc5v>;
> > >>>>> +		drivevbus-supply = <&reg_vcc5v>;
> > >>>>> +		ips-supply = <&reg_vcc5v>;
> > >>>>> +
> > >>>>> +		status = "okay";
> > >>>>> +	};
> > >>>>> +};
> > >>>>> +
> > >>>>> +#include "axp803.dtsi"
> > >>>>> +
> > >>>>> +&ac_power_supply {
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&reg_dcdc1 {
> > >>>>> +	regulator-always-on;
> > >>>>> +	regulator-min-microvolt = <3300000>;
> > >>>>> +	regulator-max-microvolt = <3300000>;
> > >>>>> +	regulator-name = "vcc-3v3";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&reg_dcdc2 {
> > >>>>> +	regulator-always-on;
> > >>>>> +	regulator-min-microvolt = <1040000>;
> > >>>>> +	regulator-max-microvolt = <1300000>;
> > >>>>> +	regulator-name = "vdd-cpux";
> > >>>>> +};
> > >>>>> +
> > >>>>> +/* DCDC3 is polyphased with DCDC2 */
> > >>>>> +
> > >>>>> +&reg_dcdc5 {
> > >>>>> +	regulator-always-on;
> > >>>>> +	regulator-min-microvolt = <1500000>;
> > >>>>> +	regulator-max-microvolt = <1500000>;
> > >>>>> +	regulator-name = "vcc-dram";
> > >>>>> +};
> > >>>>> +
> > >>>>> +/* Deviates from the reset default of 1.1V. */
> > >>>>> +&reg_dcdc6 {
> > >>>>> +	regulator-always-on;
> > >>>>> +	regulator-min-microvolt = <1200000>;
> > >>>>> +	regulator-max-microvolt = <1200000>;
> > >>>>> +	regulator-name = "vdd-sys";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&reg_aldo1 {
> > >>>>> +	regulator-min-microvolt = <3300000>;
> > >>>>> +	regulator-max-microvolt = <3300000>;
> > >>>>> +	regulator-name = "vcc-wifi";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&reg_aldo2 {
> > >>>>> +	/* Specifying R_PIO consumer would create circular dependency. */
> > >>>>> +	regulator-always-on;
> > >>>>> +	regulator-min-microvolt = <3300000>;
> > >>>>> +	regulator-max-microvolt = <3300000>;
> > >>>>> +	regulator-name = "vcc-pl";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&reg_aldo3 {
> > >>>>> +	regulator-always-on;
> > >>>>> +	regulator-min-microvolt = <3000000>;
> > >>>>> +	regulator-max-microvolt = <3000000>;
> > >>>>> +	regulator-name = "vcc-pll-avcc";
> > >>>>> +};
> > >>>>> +
> > >>>>> +/* AC200 power supply */
> > >>>>> +&reg_dldo1 {
> > >>>>> +	regulator-always-on;
> > >>>>> +	regulator-min-microvolt = <3300000>;
> > >>>>> +	regulator-max-microvolt = <3300000>;
> > >>>>> +	regulator-name = "vcc-ave-33";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&reg_dldo4 {
> > >>>>> +	regulator-min-microvolt = <3300000>;
> > >>>>> +	regulator-max-microvolt = <3300000>;
> > >>>>> +	regulator-name = "vcc-wifi-io";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&reg_drivevbus {
> > >>>>> +	regulator-name = "usb0-vbus";
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&reg_eldo1 {
> > >>>>> +	regulator-always-on;
> > >>>>> +	regulator-min-microvolt = <1800000>;
> > >>>>> +	regulator-max-microvolt = <1800000>;
> > >>>>> +	regulator-name = "vcc-cpvdd-dram-emmc";
> > >>>>> +};
> > >>>>> +
> > >>>>> +/* Supplies the arisc management core, needed by TF-A to power off cores. */
> > >>>>> +&reg_fldo2 {
> > >>>>> +	regulator-always-on;
> > >>>>> +	regulator-min-microvolt = <1100000>;
> > >>>>> +	regulator-max-microvolt = <1100000>;
> > >>>>> +	regulator-name = "vdd-cpus";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&reg_rtc_ldo {
> > >>>>> +	regulator-name = "vcc-rtc";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&simplefb_hdmi {
> > >>>>> +	vcc-hdmi-supply = <&reg_dcdc1>;
> > >>>>> +};
> > >>>>> +
> > >>>>> +&sound {
> > >>>>> +	simple-audio-card,aux-devs = <&codec_analog>;
> > >>>>> +	simple-audio-card,widgets = "Microphone", "Microphone Jack",
> > >>>>> +				    "Headphone", "Headphone Jack";
> > >>>>> +	simple-audio-card,routing =
> > >>>>> +			"Left DAC", "DACL",
> > >>>>> +			"Right DAC", "DACR",
> > >>>>> +			"Headphone Jack", "HP",
> > >>>>> +			"ADCL", "Left ADC",
> > >>>>> +			"ADCR", "Right ADC",
> > >>>>> +			"MIC2", "Microphone Jack";
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +/* On the (unpopulated) UART pads. */
> > >>>>> +&uart0 {
> > >>>>> +	pinctrl-names = "default";
> > >>>>> +	pinctrl-0 = <&uart0_pb_pins>;
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&uart1 {
> > >>>>> +	pinctrl-names = "default";
> > >>>>> +	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> > >>>>> +	uart-has-rtscts;
> > >>>>> +	status = "okay";
> > >>>>> +
> > >>>>> +	bluetooth {
> > >>>>> +		compatible = "realtek,rtl8723bs-bt";
> > >>>>> +		enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> > >>>>> +		max-speed = <1500000>;
> > >>>>> +	};
> > >>>>> +};
> > >>>>> +
> > >>>>> +&usb_otg {
> > >>>>> +	dr_mode = "host";
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>> +
> > >>>>> +&usbphy {
> > >>>>> +	usb0_vbus-supply = <&reg_drivevbus>;
> > >>>>> +	usb1_vbus-supply = <&reg_drivevbus>;
> > >>>>> +	status = "okay";
> > >>>>> +};
> > >>>>>
> > >>>>
> > >>>>
> > >>>>
> > >>>>
> > >>>>
> > >>>
> > >>>
> > >>>
> > >>>
> > >>
> > > 
> > > 
> > > 
> > > 
> > 
> 
> 
> 
> 
>

Andre Przywara Feb. 9, 2024, 12:54 a.m. UTC | #8

On Tue, 06 Feb 2024 19:27:22 +0100
Jernej Škrabec <jernej.skrabec@gmail.com> wrote:

Hi,

....

> > > >>>>> +&mmc2 {
> > > >>>>> +	pinctrl-names = "default";
> > > >>>>> +	pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
> > > >>>>> +	vmmc-supply = <&reg_dcdc1>;
> > > >>>>> +	vqmmc-supply = <&reg_eldo1>;
> > > >>>>> +	bus-width = <8>;
> > > >>>>> +	non-removable;
> > > >>>>> +	mmc-ddr-1_8v;
> > > >>>>> +	mmc-hs200-1_8v;  
> > > >>>>
> > > >>>> Aren't these speed modes enabled by default?  
> > > >>
> > > >> Enabled by who? Our current sunxi-mmc driver? I cannot find anything in
> > > >> the binding that suggests that there would be some default settings.  
> > > > 
> > > > Looking at Linux sunxi mmc driver, mmc-ddr-1_8v is enabled by default for
> > > > "new timings" variants except for H5. Anyway...  
> > > 
> > > But this is a Linux implementation detail, which we should not rely on 
> > > in a DT? And if I remember Maxime correctly back then, the plan was to 
> > > avoid those driver hacks and just say what we support in the DT, going 
> > > forward. This might be needed for other OSes, which might not support 
> > > HS-200?  
> > > >>> Sorry, mmc-hs200-1_8v is ok, but mmc-ddr-1_8v should be
> > > >>> removed.  
> > > >>
> > > >> Mmh, I am confused: I thought after the H5 eMMC mishap we figured that
> > > >> all speed modes supported by the eMMC chip should be listed in the DT?  
> > > > 
> > > > I think H5 just has (had?) driver issue. From what I can see, only highest
> > > > supported mode by kernel and chip is specified in all Allwinner DTs.
> > > > mmc-ddr-1_8v is only specified by two recent board addition, where I missed
> > > > it while reviewing.
> > > >   
> > > >> So any driver wouldn't need to make assumptions, and if a particular
> > > >> mode shows problems on a board, we just remove that mode from the DT.
> > > >> Actually, thinking about that, I guess I should list HS-400 as well? The
> > > >> BSP kernel uses that mode.  
> > > > 
> > > > Sure, but it also calibrates timing for it. If you'll specify HS400, kernel
> > > > will try to use it, but it won't work.  
> > > 
> > > But this is also a limitation of the current Linux kernel driver. And 
> > > since we indeed don't support HS-400, we explicitly remove it from the 
> > > capability list, *after* the call to mmc_of_parse():
> > > 
> > > drivers/mmc/host/sunxi-mmc.c:1460
> > >          /* TODO: This driver doesn't support HS400 mode yet */
> > >          mmc->caps2 &= ~MMC_CAP2_HS400;
> > > 
> > > So I think this should be safe?  
> > 
> > Right. Can you test it?
> > 
> > Best regards,
> > Jernej
> >   
> > > 
> > > Cheers,
> > > Andre
> > >   
> > > >   
> > > >> Or do you mean to say that in particular DDR (@1.8V) is problematic? I
> > > >> cannot test at the moment, but could try later to force that mode.  
> > > > 
> > > > No, no need.  
> 
> If we go in new direction, then it would be good to test it.

So I did this, and curiously enough MMC DDR didn't work. It's a bit
odd, since 50 MHz DDR sounds less problematic than 200 MHz SDR, but
apparently there is more than just the frequency at play here.
Announcing HS-400 didn't make a difference in Linux, as expected, since
the driver filters it out.

So I will drop mmc-ddr-1_8v, but add mmc-hs400-1_8v.

Thanks,
Andre


> 
> Best regards,
> Jernej
> 
> > > > 
> > > > Best regards,
> > > > Jernej
> > > >   
> > > >>
> > > >> Cheers,
> > > >> Andre
> > > >>
> > > >>  
> > > >>>>> +	cap-mmc-hw-reset;
> > > >>>>> +	status = "okay";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&ohci0 {
> > > >>>>> +	status = "okay";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&ohci1 {
> > > >>>>> +	status = "okay";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&pio {
> > > >>>>> +	vcc-pb-supply = <&reg_dcdc1>;
> > > >>>>> +	vcc-pc-supply = <&reg_dcdc1>;
> > > >>>>> +	vcc-pd-supply = <&reg_dcdc1>;
> > > >>>>> +	vcc-pe-supply = <&reg_dcdc1>;
> > > >>>>> +	vcc-pf-supply = <&reg_dcdc1>;
> > > >>>>> +	vcc-pg-supply = <&reg_dldo4>;
> > > >>>>> +	vcc-ph-supply = <&reg_dcdc1>;
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&r_ir {
> > > >>>>> +	status = "okay";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&r_pio {
> > > >>>>> +	/*
> > > >>>>> +	 * We cannot add that supply for now since it would create a circular
> > > >>>>> +	 * dependency between pinctrl, the regulator and the RSB Bus.
> > > >>>>> +	 *
> > > >>>>> +	 * vcc-pl-supply = <&reg_aldo2>;
> > > >>>>> +	 */
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&r_rsb {
> > > >>>>> +	status = "okay";
> > > >>>>> +
> > > >>>>> +	axp803: pmic@3a3 {
> > > >>>>> +		compatible = "x-powers,axp803";
> > > >>>>> +		reg = <0x3a3>;
> > > >>>>> +		interrupt-parent = <&r_intc>;
> > > >>>>> +		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_LOW>;
> > > >>>>> +		x-powers,drive-vbus-en;
> > > >>>>> +
> > > >>>>> +		vin1-supply = <&reg_vcc5v>;
> > > >>>>> +		vin2-supply = <&reg_vcc5v>;
> > > >>>>> +		vin3-supply = <&reg_vcc5v>;
> > > >>>>> +		vin5-supply = <&reg_vcc5v>;
> > > >>>>> +		vin6-supply = <&reg_vcc5v>;
> > > >>>>> +		aldoin-supply = <&reg_vcc5v>;
> > > >>>>> +		dldoin-supply = <&reg_vcc5v>;
> > > >>>>> +		eldoin-supply = <&reg_vcc5v>;
> > > >>>>> +		fldoin-supply = <&reg_vcc5v>;
> > > >>>>> +		drivevbus-supply = <&reg_vcc5v>;
> > > >>>>> +		ips-supply = <&reg_vcc5v>;
> > > >>>>> +
> > > >>>>> +		status = "okay";
> > > >>>>> +	};
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +#include "axp803.dtsi"
> > > >>>>> +
> > > >>>>> +&ac_power_supply {
> > > >>>>> +	status = "okay";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&reg_dcdc1 {
> > > >>>>> +	regulator-always-on;
> > > >>>>> +	regulator-min-microvolt = <3300000>;
> > > >>>>> +	regulator-max-microvolt = <3300000>;
> > > >>>>> +	regulator-name = "vcc-3v3";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&reg_dcdc2 {
> > > >>>>> +	regulator-always-on;
> > > >>>>> +	regulator-min-microvolt = <1040000>;
> > > >>>>> +	regulator-max-microvolt = <1300000>;
> > > >>>>> +	regulator-name = "vdd-cpux";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +/* DCDC3 is polyphased with DCDC2 */
> > > >>>>> +
> > > >>>>> +&reg_dcdc5 {
> > > >>>>> +	regulator-always-on;
> > > >>>>> +	regulator-min-microvolt = <1500000>;
> > > >>>>> +	regulator-max-microvolt = <1500000>;
> > > >>>>> +	regulator-name = "vcc-dram";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +/* Deviates from the reset default of 1.1V. */
> > > >>>>> +&reg_dcdc6 {
> > > >>>>> +	regulator-always-on;
> > > >>>>> +	regulator-min-microvolt = <1200000>;
> > > >>>>> +	regulator-max-microvolt = <1200000>;
> > > >>>>> +	regulator-name = "vdd-sys";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&reg_aldo1 {
> > > >>>>> +	regulator-min-microvolt = <3300000>;
> > > >>>>> +	regulator-max-microvolt = <3300000>;
> > > >>>>> +	regulator-name = "vcc-wifi";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&reg_aldo2 {
> > > >>>>> +	/* Specifying R_PIO consumer would create circular dependency. */
> > > >>>>> +	regulator-always-on;
> > > >>>>> +	regulator-min-microvolt = <3300000>;
> > > >>>>> +	regulator-max-microvolt = <3300000>;
> > > >>>>> +	regulator-name = "vcc-pl";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&reg_aldo3 {
> > > >>>>> +	regulator-always-on;
> > > >>>>> +	regulator-min-microvolt = <3000000>;
> > > >>>>> +	regulator-max-microvolt = <3000000>;
> > > >>>>> +	regulator-name = "vcc-pll-avcc";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +/* AC200 power supply */
> > > >>>>> +&reg_dldo1 {
> > > >>>>> +	regulator-always-on;
> > > >>>>> +	regulator-min-microvolt = <3300000>;
> > > >>>>> +	regulator-max-microvolt = <3300000>;
> > > >>>>> +	regulator-name = "vcc-ave-33";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&reg_dldo4 {
> > > >>>>> +	regulator-min-microvolt = <3300000>;
> > > >>>>> +	regulator-max-microvolt = <3300000>;
> > > >>>>> +	regulator-name = "vcc-wifi-io";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&reg_drivevbus {
> > > >>>>> +	regulator-name = "usb0-vbus";
> > > >>>>> +	status = "okay";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&reg_eldo1 {
> > > >>>>> +	regulator-always-on;
> > > >>>>> +	regulator-min-microvolt = <1800000>;
> > > >>>>> +	regulator-max-microvolt = <1800000>;
> > > >>>>> +	regulator-name = "vcc-cpvdd-dram-emmc";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +/* Supplies the arisc management core, needed by TF-A to power off cores. */
> > > >>>>> +&reg_fldo2 {
> > > >>>>> +	regulator-always-on;
> > > >>>>> +	regulator-min-microvolt = <1100000>;
> > > >>>>> +	regulator-max-microvolt = <1100000>;
> > > >>>>> +	regulator-name = "vdd-cpus";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&reg_rtc_ldo {
> > > >>>>> +	regulator-name = "vcc-rtc";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&simplefb_hdmi {
> > > >>>>> +	vcc-hdmi-supply = <&reg_dcdc1>;
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&sound {
> > > >>>>> +	simple-audio-card,aux-devs = <&codec_analog>;
> > > >>>>> +	simple-audio-card,widgets = "Microphone", "Microphone Jack",
> > > >>>>> +				    "Headphone", "Headphone Jack";
> > > >>>>> +	simple-audio-card,routing =
> > > >>>>> +			"Left DAC", "DACL",
> > > >>>>> +			"Right DAC", "DACR",
> > > >>>>> +			"Headphone Jack", "HP",
> > > >>>>> +			"ADCL", "Left ADC",
> > > >>>>> +			"ADCR", "Right ADC",
> > > >>>>> +			"MIC2", "Microphone Jack";
> > > >>>>> +	status = "okay";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +/* On the (unpopulated) UART pads. */
> > > >>>>> +&uart0 {
> > > >>>>> +	pinctrl-names = "default";
> > > >>>>> +	pinctrl-0 = <&uart0_pb_pins>;
> > > >>>>> +	status = "okay";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&uart1 {
> > > >>>>> +	pinctrl-names = "default";
> > > >>>>> +	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> > > >>>>> +	uart-has-rtscts;
> > > >>>>> +	status = "okay";
> > > >>>>> +
> > > >>>>> +	bluetooth {
> > > >>>>> +		compatible = "realtek,rtl8723bs-bt";
> > > >>>>> +		enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> > > >>>>> +		max-speed = <1500000>;
> > > >>>>> +	};
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&usb_otg {
> > > >>>>> +	dr_mode = "host";
> > > >>>>> +	status = "okay";
> > > >>>>> +};
> > > >>>>> +
> > > >>>>> +&usbphy {
> > > >>>>> +	usb0_vbus-supply = <&reg_drivevbus>;
> > > >>>>> +	usb1_vbus-supply = <&reg_drivevbus>;
> > > >>>>> +	status = "okay";
> > > >>>>> +};
> > > >>>>>  
> > > >>>>
> > > >>>>
> > > >>>>
> > > >>>>
> > > >>>>  
> > > >>>
> > > >>>
> > > >>>
> > > >>>  
> > > >>  
> > > > 
> > > > 
> > > > 
> > > >   
> > >   
> > 
> > 
> > 
> > 
> >   
> 
> 
> 
> 
>

[3/3] arm64: dts: allwinner: Add Jide Remix Mini PC support

Commit Message

Comments

Patch