| Message ID | 20240204101054.152012-3-andre.przywara@arm.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | arm64: dts: allwinner: Add BananaPi M4 Berry | expand |
Dne nedelja, 04. februar 2024 ob 11:10:54 CET je Andre Przywara napisal(a): > The BananaPi M4 Berry is a development board using the Allwinner H618 > SoC. It comes with the following specs: > - Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache) > - 2 GiB LPDDR4 DRAM > - 8 GiB eMMC flash > - AXP313a PMIC > - Gigabit Ethernet, using RTL8211 PHY > - RTL8821CU USB WiFi chip > - HDMI port > - 4 * USB 2.0 ports, via an on-board hub chip > - microSD card slot > - 3.5mm A/V port > - power supply and USB-OTG via USB-C connector > > Add a devicetree file describing the components that we already have > bindings for, that excludes audio and video at the moment. > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > --- > arch/arm64/boot/dts/allwinner/Makefile | 1 + > .../sun50i-h618-bananapi-m4-berry.dts | 223 ++++++++++++++++++ > 2 files changed, 224 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile > index 2db3b15ad09f..1c5c204a109b 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -43,5 +43,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-cb1-manta.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-pi.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-bananapi-m4-berry.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts b/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts > new file mode 100644 > index 000000000000..a3f8ff75db42 > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts > @@ -0,0 +1,223 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2023 Arm Ltd. > + */ > + > +/dts-v1/; > + > +#include "sun50i-h616.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/linux-event-codes.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/leds/common.h> > + > +/ { > + model = "BananaPi M4 Berry"; > + compatible = "sinovoip,bananapi-m4-berry", "allwinner,sun50i-h618"; > + > + aliases { > + ethernet0 = &emac0; > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + led-0 { > + function = LED_FUNCTION_STATUS; > + color = <LED_COLOR_ID_GREEN>; > + gpios = <&pio 2 12 GPIO_ACTIVE_LOW>; /* PC12 */ > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + key-sw3 { > + label = "sw3"; > + linux,code = <BTN_0>; > + gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */ > + }; > + }; > + > + reg_vcc5v: regulator-5v { > + /* board wide 5V supply directly from the USB-C socket */ > + compatible = "regulator-fixed"; > + regulator-name = "vcc-5v"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; > + > + reg_usb_vbus: regulator-usb-vbus { > + /* separate discrete regulator for the USB ports */ > + compatible = "regulator-fixed"; > + regulator-name = "usb-vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + vin-supply = <®_vcc5v>; > + }; > + > + reg_3v3: regulator-3v3 { > + /* separate discrete regulator for WiFi and Ethernet PHY */ > + compatible = "regulator-fixed"; > + regulator-name = "vcc-3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <®_vcc5v>; > + }; > +}; > + > +&cpu0 { > + cpu-supply = <®_dcdc2>; > +}; > + > +/* Connected to an on-board RTL8821CU USB WiFi chip. */ > +&ehci1 { > + status = "okay"; > +}; > + > +/* EHCI2 is on unpopulated pins */ > + > +/* Connected to an on-board FE1.1s USB hub chip, supplying 4 USB-A ports. */ > +&ehci3 { > + status = "okay"; > +}; > + > +&emac0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&ext_rgmii_pins>; > + phy-mode = "rgmii"; > + phy-handle = <&ext_rgmii_phy>; > + phy-supply = <®_3v3>; > + allwinner,rx-delay-ps = <3100>; > + allwinner,tx-delay-ps = <700>; > + status = "okay"; > +}; > + > +&ir { > + status = "okay"; > +}; > + > +&mdio0 { > + ext_rgmii_phy: ethernet-phy@1 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <1>; > + reset-gpios = <&pio 8 16 GPIO_ACTIVE_LOW>; /* PI16 */ > + }; > +}; > + > +&mmc0 { > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > + vmmc-supply = <®_dldo1>; > + bus-width = <4>; > + status = "okay"; > +}; > + > +&mmc2 { > + vmmc-supply = <®_dldo1>; > + vqmmc-supply = <®_aldo1>; > + bus-width = <8>; > + non-removable; > + cap-mmc-hw-reset; > + mmc-ddr-1_8v; This one should be dropped. Best regards, Jernej > + mmc-hs200-1_8v; > + status = "okay"; > +}; > + > +/* USB ports 1 and 3 connect to onboard devices that are high-speed only. */ > + > +/* OHCI2 is on unpopulated pins */ > + > +&pio { > + vcc-pc-supply = <®_aldo1>; > + vcc-pf-supply = <®_dldo1>; > + vcc-pg-supply = <®_dldo1>; > + vcc-ph-supply = <®_dldo1>; > + vcc-pi-supply = <®_dldo1>; > +}; > + > +&r_i2c { > + status = "okay"; > + > + axp313: pmic@36 { > + compatible = "x-powers,axp313a"; > + reg = <0x36>; > + #interrupt-cells = <1>; > + interrupt-controller; > + interrupt-parent = <&pio>; > + > + vin1-supply = <®_vcc5v>; > + vin2-supply = <®_vcc5v>; > + vin3-supply = <®_vcc5v>; > + > + regulators { > + reg_aldo1: aldo1 { > + regulator-always-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc-1v8-pll"; > + }; > + > + reg_dldo1: dldo1 { > + regulator-always-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc-3v3-io"; > + }; > + > + reg_dcdc1: dcdc1 { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <990000>; > + regulator-name = "vdd-gpu-sys"; > + }; > + > + reg_dcdc2: dcdc2 { > + regulator-always-on; > + regulator-min-microvolt = <810000>; > + regulator-max-microvolt = <1100000>; > + regulator-name = "vdd-cpu"; > + }; > + > + reg_dcdc3: dcdc3 { > + regulator-always-on; > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1100000>; > + regulator-name = "vdd-dram"; > + }; > + }; > + }; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_ph_pins>; > + status = "okay"; > +}; > + > +&usbotg { > + /* > + * PHY0 pins are connected to a USB-C socket, but a role switch is not > + * implemented: both CC pins are pulled to GND via a 5.1K resistor. > + * The VBUS pins power the device, so a fixed peripheral mode > + * is the best choice. > + * The board can be powered via GPIOs, in this case port0 *can* > + * act as a host (with a cable/adapter ignoring CC), as VBUS is > + * then provided by the GPIOs. Any user of this setup would > + * need to adjust the DT accordingly: dr_mode set to "host", > + * enabling OHCI0 and EHCI0. > + */ > + dr_mode = "peripheral"; > + status = "okay"; > +}; > + > +&usbphy { > + usb3_vbus-supply = <®_usb_vbus>; > + status = "okay"; > +}; >
Hi Andre! Dne ponedeljek, 05. februar 2024 ob 19:19:26 CET je Jernej Škrabec napisal(a): > Dne nedelja, 04. februar 2024 ob 11:10:54 CET je Andre Przywara napisal(a): > > The BananaPi M4 Berry is a development board using the Allwinner H618 > > SoC. It comes with the following specs: > > - Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache) > > - 2 GiB LPDDR4 DRAM > > - 8 GiB eMMC flash > > - AXP313a PMIC > > - Gigabit Ethernet, using RTL8211 PHY > > - RTL8821CU USB WiFi chip > > - HDMI port > > - 4 * USB 2.0 ports, via an on-board hub chip > > - microSD card slot > > - 3.5mm A/V port > > - power supply and USB-OTG via USB-C connector > > > > Add a devicetree file describing the components that we already have > > bindings for, that excludes audio and video at the moment. > > > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > > --- > > arch/arm64/boot/dts/allwinner/Makefile | 1 + > > .../sun50i-h618-bananapi-m4-berry.dts | 223 ++++++++++++++++++ > > 2 files changed, 224 insertions(+) > > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts > > > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile > > index 2db3b15ad09f..1c5c204a109b 100644 > > --- a/arch/arm64/boot/dts/allwinner/Makefile > > +++ b/arch/arm64/boot/dts/allwinner/Makefile > > @@ -43,5 +43,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-cb1-manta.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-pi.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb > > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-bananapi-m4-berry.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts b/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts > > new file mode 100644 > > index 000000000000..a3f8ff75db42 > > --- /dev/null > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts > > @@ -0,0 +1,223 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +/* > > + * Copyright (C) 2023 Arm Ltd. > > + */ > > + > > +/dts-v1/; > > + > > +#include "sun50i-h616.dtsi" > > + > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/input/linux-event-codes.h> > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > +#include <dt-bindings/leds/common.h> > > + > > +/ { > > + model = "BananaPi M4 Berry"; > > + compatible = "sinovoip,bananapi-m4-berry", "allwinner,sun50i-h618"; > > + > > + aliases { > > + ethernet0 = &emac0; > > + serial0 = &uart0; > > + }; > > + > > + chosen { > > + stdout-path = "serial0:115200n8"; > > + }; > > + > > + leds { > > + compatible = "gpio-leds"; > > + > > + led-0 { > > + function = LED_FUNCTION_STATUS; > > + color = <LED_COLOR_ID_GREEN>; > > + gpios = <&pio 2 12 GPIO_ACTIVE_LOW>; /* PC12 */ > > + }; > > + }; > > + > > + gpio-keys { > > + compatible = "gpio-keys"; > > + > > + key-sw3 { > > + label = "sw3"; > > + linux,code = <BTN_0>; > > + gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */ > > + }; > > + }; > > + > > + reg_vcc5v: regulator-5v { > > + /* board wide 5V supply directly from the USB-C socket */ > > + compatible = "regulator-fixed"; > > + regulator-name = "vcc-5v"; > > + regulator-min-microvolt = <5000000>; > > + regulator-max-microvolt = <5000000>; > > + regulator-always-on; > > + }; > > + > > + reg_usb_vbus: regulator-usb-vbus { > > + /* separate discrete regulator for the USB ports */ > > + compatible = "regulator-fixed"; > > + regulator-name = "usb-vbus"; > > + regulator-min-microvolt = <5000000>; > > + regulator-max-microvolt = <5000000>; > > + vin-supply = <®_vcc5v>; > > + }; > > + > > + reg_3v3: regulator-3v3 { > > + /* separate discrete regulator for WiFi and Ethernet PHY */ > > + compatible = "regulator-fixed"; > > + regulator-name = "vcc-3v3"; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + vin-supply = <®_vcc5v>; > > + }; > > +}; > > + > > +&cpu0 { > > + cpu-supply = <®_dcdc2>; > > +}; > > + > > +/* Connected to an on-board RTL8821CU USB WiFi chip. */ > > +&ehci1 { > > + status = "okay"; > > +}; > > + > > +/* EHCI2 is on unpopulated pins */ > > + > > +/* Connected to an on-board FE1.1s USB hub chip, supplying 4 USB-A ports. */ > > +&ehci3 { > > + status = "okay"; > > +}; > > + > > +&emac0 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&ext_rgmii_pins>; > > + phy-mode = "rgmii"; > > + phy-handle = <&ext_rgmii_phy>; > > + phy-supply = <®_3v3>; > > + allwinner,rx-delay-ps = <3100>; > > + allwinner,tx-delay-ps = <700>; > > + status = "okay"; > > +}; > > + > > +&ir { > > + status = "okay"; > > +}; > > + > > +&mdio0 { > > + ext_rgmii_phy: ethernet-phy@1 { > > + compatible = "ethernet-phy-ieee802.3-c22"; > > + reg = <1>; > > + reset-gpios = <&pio 8 16 GPIO_ACTIVE_LOW>; /* PI16 */ > > + }; > > +}; > > + > > +&mmc0 { > > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > > + vmmc-supply = <®_dldo1>; > > + bus-width = <4>; > > + status = "okay"; > > +}; > > + > > +&mmc2 { > > + vmmc-supply = <®_dldo1>; > > + vqmmc-supply = <®_aldo1>; > > + bus-width = <8>; > > + non-removable; > > + cap-mmc-hw-reset; > > + mmc-ddr-1_8v; > > This one should be dropped. Can you please test this one? If it works, I'll merge this series. Best regards, Jernej > > + mmc-hs200-1_8v; > > + status = "okay"; > > +}; > > + > > +/* USB ports 1 and 3 connect to onboard devices that are high-speed only. */ > > + > > +/* OHCI2 is on unpopulated pins */ > > + > > +&pio { > > + vcc-pc-supply = <®_aldo1>; > > + vcc-pf-supply = <®_dldo1>; > > + vcc-pg-supply = <®_dldo1>; > > + vcc-ph-supply = <®_dldo1>; > > + vcc-pi-supply = <®_dldo1>; > > +}; > > + > > +&r_i2c { > > + status = "okay"; > > + > > + axp313: pmic@36 { > > + compatible = "x-powers,axp313a"; > > + reg = <0x36>; > > + #interrupt-cells = <1>; > > + interrupt-controller; > > + interrupt-parent = <&pio>; > > + > > + vin1-supply = <®_vcc5v>; > > + vin2-supply = <®_vcc5v>; > > + vin3-supply = <®_vcc5v>; > > + > > + regulators { > > + reg_aldo1: aldo1 { > > + regulator-always-on; > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <1800000>; > > + regulator-name = "vcc-1v8-pll"; > > + }; > > + > > + reg_dldo1: dldo1 { > > + regulator-always-on; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-name = "vcc-3v3-io"; > > + }; > > + > > + reg_dcdc1: dcdc1 { > > + regulator-always-on; > > + regulator-min-microvolt = <810000>; > > + regulator-max-microvolt = <990000>; > > + regulator-name = "vdd-gpu-sys"; > > + }; > > + > > + reg_dcdc2: dcdc2 { > > + regulator-always-on; > > + regulator-min-microvolt = <810000>; > > + regulator-max-microvolt = <1100000>; > > + regulator-name = "vdd-cpu"; > > + }; > > + > > + reg_dcdc3: dcdc3 { > > + regulator-always-on; > > + regulator-min-microvolt = <1100000>; > > + regulator-max-microvolt = <1100000>; > > + regulator-name = "vdd-dram"; > > + }; > > + }; > > + }; > > +}; > > + > > +&uart0 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&uart0_ph_pins>; > > + status = "okay"; > > +}; > > + > > +&usbotg { > > + /* > > + * PHY0 pins are connected to a USB-C socket, but a role switch is not > > + * implemented: both CC pins are pulled to GND via a 5.1K resistor. > > + * The VBUS pins power the device, so a fixed peripheral mode > > + * is the best choice. > > + * The board can be powered via GPIOs, in this case port0 *can* > > + * act as a host (with a cable/adapter ignoring CC), as VBUS is > > + * then provided by the GPIOs. Any user of this setup would > > + * need to adjust the DT accordingly: dr_mode set to "host", > > + * enabling OHCI0 and EHCI0. > > + */ > > + dr_mode = "peripheral"; > > + status = "okay"; > > +}; > > + > > +&usbphy { > > + usb3_vbus-supply = <®_usb_vbus>; > > + status = "okay"; > > +}; > > > > > > >
On Sun, 11 Feb 2024 21:22:11 +0100 Jernej Škrabec <jernej.skrabec@gmail.com> wrote: Hi Jernej, > Hi Andre! > > Dne ponedeljek, 05. februar 2024 ob 19:19:26 CET je Jernej Škrabec napisal(a): > > Dne nedelja, 04. februar 2024 ob 11:10:54 CET je Andre Przywara napisal(a): > > > The BananaPi M4 Berry is a development board using the Allwinner H618 > > > SoC. It comes with the following specs: > > > - Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache) > > > - 2 GiB LPDDR4 DRAM > > > - 8 GiB eMMC flash > > > - AXP313a PMIC > > > - Gigabit Ethernet, using RTL8211 PHY > > > - RTL8821CU USB WiFi chip > > > - HDMI port > > > - 4 * USB 2.0 ports, via an on-board hub chip > > > - microSD card slot > > > - 3.5mm A/V port > > > - power supply and USB-OTG via USB-C connector > > > > > > Add a devicetree file describing the components that we already have > > > bindings for, that excludes audio and video at the moment. > > > > > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> > > > --- > > > arch/arm64/boot/dts/allwinner/Makefile | 1 + > > > .../sun50i-h618-bananapi-m4-berry.dts | 223 ++++++++++++++++++ > > > 2 files changed, 224 insertions(+) > > > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts > > > > > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile > > > index 2db3b15ad09f..1c5c204a109b 100644 > > > --- a/arch/arm64/boot/dts/allwinner/Makefile > > > +++ b/arch/arm64/boot/dts/allwinner/Makefile > > > @@ -43,5 +43,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-cb1-manta.dtb > > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-pi.dtb > > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb > > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb > > > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-bananapi-m4-berry.dtb > > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb > > > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb > > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts b/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts > > > new file mode 100644 > > > index 000000000000..a3f8ff75db42 > > > --- /dev/null > > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts > > > @@ -0,0 +1,223 @@ > > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > > +/* > > > + * Copyright (C) 2023 Arm Ltd. > > > + */ > > > + > > > +/dts-v1/; > > > + > > > +#include "sun50i-h616.dtsi" > > > + > > > +#include <dt-bindings/gpio/gpio.h> > > > +#include <dt-bindings/input/linux-event-codes.h> > > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > > +#include <dt-bindings/leds/common.h> > > > + > > > +/ { > > > + model = "BananaPi M4 Berry"; > > > + compatible = "sinovoip,bananapi-m4-berry", "allwinner,sun50i-h618"; > > > + > > > + aliases { > > > + ethernet0 = &emac0; > > > + serial0 = &uart0; > > > + }; > > > + > > > + chosen { > > > + stdout-path = "serial0:115200n8"; > > > + }; > > > + > > > + leds { > > > + compatible = "gpio-leds"; > > > + > > > + led-0 { > > > + function = LED_FUNCTION_STATUS; > > > + color = <LED_COLOR_ID_GREEN>; > > > + gpios = <&pio 2 12 GPIO_ACTIVE_LOW>; /* PC12 */ > > > + }; > > > + }; > > > + > > > + gpio-keys { > > > + compatible = "gpio-keys"; > > > + > > > + key-sw3 { > > > + label = "sw3"; > > > + linux,code = <BTN_0>; > > > + gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */ > > > + }; > > > + }; > > > + > > > + reg_vcc5v: regulator-5v { > > > + /* board wide 5V supply directly from the USB-C socket */ > > > + compatible = "regulator-fixed"; > > > + regulator-name = "vcc-5v"; > > > + regulator-min-microvolt = <5000000>; > > > + regulator-max-microvolt = <5000000>; > > > + regulator-always-on; > > > + }; > > > + > > > + reg_usb_vbus: regulator-usb-vbus { > > > + /* separate discrete regulator for the USB ports */ > > > + compatible = "regulator-fixed"; > > > + regulator-name = "usb-vbus"; > > > + regulator-min-microvolt = <5000000>; > > > + regulator-max-microvolt = <5000000>; > > > + vin-supply = <®_vcc5v>; > > > + }; > > > + > > > + reg_3v3: regulator-3v3 { > > > + /* separate discrete regulator for WiFi and Ethernet PHY */ > > > + compatible = "regulator-fixed"; > > > + regulator-name = "vcc-3v3"; > > > + regulator-min-microvolt = <3300000>; > > > + regulator-max-microvolt = <3300000>; > > > + vin-supply = <®_vcc5v>; > > > + }; > > > +}; > > > + > > > +&cpu0 { > > > + cpu-supply = <®_dcdc2>; > > > +}; > > > + > > > +/* Connected to an on-board RTL8821CU USB WiFi chip. */ > > > +&ehci1 { > > > + status = "okay"; > > > +}; > > > + > > > +/* EHCI2 is on unpopulated pins */ > > > + > > > +/* Connected to an on-board FE1.1s USB hub chip, supplying 4 USB-A ports. */ > > > +&ehci3 { > > > + status = "okay"; > > > +}; > > > + > > > +&emac0 { > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&ext_rgmii_pins>; > > > + phy-mode = "rgmii"; > > > + phy-handle = <&ext_rgmii_phy>; > > > + phy-supply = <®_3v3>; > > > + allwinner,rx-delay-ps = <3100>; > > > + allwinner,tx-delay-ps = <700>; > > > + status = "okay"; > > > +}; > > > + > > > +&ir { > > > + status = "okay"; > > > +}; > > > + > > > +&mdio0 { > > > + ext_rgmii_phy: ethernet-phy@1 { > > > + compatible = "ethernet-phy-ieee802.3-c22"; > > > + reg = <1>; > > > + reset-gpios = <&pio 8 16 GPIO_ACTIVE_LOW>; /* PI16 */ > > > + }; > > > +}; > > > + > > > +&mmc0 { > > > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > > > + vmmc-supply = <®_dldo1>; > > > + bus-width = <4>; > > > + status = "okay"; > > > +}; > > > + > > > +&mmc2 { > > > + vmmc-supply = <®_dldo1>; > > > + vqmmc-supply = <®_aldo1>; > > > + bus-width = <8>; > > > + non-removable; > > > + cap-mmc-hw-reset; > > > + mmc-ddr-1_8v; > > > > This one should be dropped. > > Can you please test this one? If it works, I'll merge this series. Unfortunately I cannot test, because I don't have that board. The DT is entirely based on the schematic. As stated in the cover letter, I was hoping for people out there to test this. To be honest, I would feel better if someome provides a Tested-by: tag before we merge that. Devils is often in the details, even with seemingly straight-forward DTs like this. Cheers, Andre > Best regards, > Jernej > > > > + mmc-hs200-1_8v; > > > + status = "okay"; > > > +}; > > > + > > > +/* USB ports 1 and 3 connect to onboard devices that are high-speed only. */ > > > + > > > +/* OHCI2 is on unpopulated pins */ > > > + > > > +&pio { > > > + vcc-pc-supply = <®_aldo1>; > > > + vcc-pf-supply = <®_dldo1>; > > > + vcc-pg-supply = <®_dldo1>; > > > + vcc-ph-supply = <®_dldo1>; > > > + vcc-pi-supply = <®_dldo1>; > > > +}; > > > + > > > +&r_i2c { > > > + status = "okay"; > > > + > > > + axp313: pmic@36 { > > > + compatible = "x-powers,axp313a"; > > > + reg = <0x36>; > > > + #interrupt-cells = <1>; > > > + interrupt-controller; > > > + interrupt-parent = <&pio>; > > > + > > > + vin1-supply = <®_vcc5v>; > > > + vin2-supply = <®_vcc5v>; > > > + vin3-supply = <®_vcc5v>; > > > + > > > + regulators { > > > + reg_aldo1: aldo1 { > > > + regulator-always-on; > > > + regulator-min-microvolt = <1800000>; > > > + regulator-max-microvolt = <1800000>; > > > + regulator-name = "vcc-1v8-pll"; > > > + }; > > > + > > > + reg_dldo1: dldo1 { > > > + regulator-always-on; > > > + regulator-min-microvolt = <3300000>; > > > + regulator-max-microvolt = <3300000>; > > > + regulator-name = "vcc-3v3-io"; > > > + }; > > > + > > > + reg_dcdc1: dcdc1 { > > > + regulator-always-on; > > > + regulator-min-microvolt = <810000>; > > > + regulator-max-microvolt = <990000>; > > > + regulator-name = "vdd-gpu-sys"; > > > + }; > > > + > > > + reg_dcdc2: dcdc2 { > > > + regulator-always-on; > > > + regulator-min-microvolt = <810000>; > > > + regulator-max-microvolt = <1100000>; > > > + regulator-name = "vdd-cpu"; > > > + }; > > > + > > > + reg_dcdc3: dcdc3 { > > > + regulator-always-on; > > > + regulator-min-microvolt = <1100000>; > > > + regulator-max-microvolt = <1100000>; > > > + regulator-name = "vdd-dram"; > > > + }; > > > + }; > > > + }; > > > +}; > > > + > > > +&uart0 { > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&uart0_ph_pins>; > > > + status = "okay"; > > > +}; > > > + > > > +&usbotg { > > > + /* > > > + * PHY0 pins are connected to a USB-C socket, but a role switch is not > > > + * implemented: both CC pins are pulled to GND via a 5.1K resistor. > > > + * The VBUS pins power the device, so a fixed peripheral mode > > > + * is the best choice. > > > + * The board can be powered via GPIOs, in this case port0 *can* > > > + * act as a host (with a cable/adapter ignoring CC), as VBUS is > > > + * then provided by the GPIOs. Any user of this setup would > > > + * need to adjust the DT accordingly: dr_mode set to "host", > > > + * enabling OHCI0 and EHCI0. > > > + */ > > > + dr_mode = "peripheral"; > > > + status = "okay"; > > > +}; > > > + > > > +&usbphy { > > > + usb3_vbus-supply = <®_usb_vbus>; > > > + status = "okay"; > > > +}; > > > > > > > > > > > > > > > > > >
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index 2db3b15ad09f..1c5c204a109b 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -43,5 +43,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-cb1-manta.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-pi.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-bananapi-m4-berry.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts b/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts new file mode 100644 index 000000000000..a3f8ff75db42 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts @@ -0,0 +1,223 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2023 Arm Ltd. + */ + +/dts-v1/; + +#include "sun50i-h616.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/linux-event-codes.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/leds/common.h> + +/ { + model = "BananaPi M4 Berry"; + compatible = "sinovoip,bananapi-m4-berry", "allwinner,sun50i-h618"; + + aliases { + ethernet0 = &emac0; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + gpios = <&pio 2 12 GPIO_ACTIVE_LOW>; /* PC12 */ + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + key-sw3 { + label = "sw3"; + linux,code = <BTN_0>; + gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */ + }; + }; + + reg_vcc5v: regulator-5v { + /* board wide 5V supply directly from the USB-C socket */ + compatible = "regulator-fixed"; + regulator-name = "vcc-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + reg_usb_vbus: regulator-usb-vbus { + /* separate discrete regulator for the USB ports */ + compatible = "regulator-fixed"; + regulator-name = "usb-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <®_vcc5v>; + }; + + reg_3v3: regulator-3v3 { + /* separate discrete regulator for WiFi and Ethernet PHY */ + compatible = "regulator-fixed"; + regulator-name = "vcc-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <®_vcc5v>; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +/* Connected to an on-board RTL8821CU USB WiFi chip. */ +&ehci1 { + status = "okay"; +}; + +/* EHCI2 is on unpopulated pins */ + +/* Connected to an on-board FE1.1s USB hub chip, supplying 4 USB-A ports. */ +&ehci3 { + status = "okay"; +}; + +&emac0 { + pinctrl-names = "default"; + pinctrl-0 = <&ext_rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_3v3>; + allwinner,rx-delay-ps = <3100>; + allwinner,tx-delay-ps = <700>; + status = "okay"; +}; + +&ir { + status = "okay"; +}; + +&mdio0 { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + reset-gpios = <&pio 8 16 GPIO_ACTIVE_LOW>; /* PI16 */ + }; +}; + +&mmc0 { + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + vmmc-supply = <®_dldo1>; + bus-width = <4>; + status = "okay"; +}; + +&mmc2 { + vmmc-supply = <®_dldo1>; + vqmmc-supply = <®_aldo1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + status = "okay"; +}; + +/* USB ports 1 and 3 connect to onboard devices that are high-speed only. */ + +/* OHCI2 is on unpopulated pins */ + +&pio { + vcc-pc-supply = <®_aldo1>; + vcc-pf-supply = <®_dldo1>; + vcc-pg-supply = <®_dldo1>; + vcc-ph-supply = <®_dldo1>; + vcc-pi-supply = <®_dldo1>; +}; + +&r_i2c { + status = "okay"; + + axp313: pmic@36 { + compatible = "x-powers,axp313a"; + reg = <0x36>; + #interrupt-cells = <1>; + interrupt-controller; + interrupt-parent = <&pio>; + + vin1-supply = <®_vcc5v>; + vin2-supply = <®_vcc5v>; + vin3-supply = <®_vcc5v>; + + regulators { + reg_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1v8-pll"; + }; + + reg_dldo1: dldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3-io"; + }; + + reg_dcdc1: dcdc1 { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <990000>; + regulator-name = "vdd-gpu-sys"; + }; + + reg_dcdc2: dcdc2 { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpu"; + }; + + reg_dcdc3: dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-dram"; + }; + }; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ph_pins>; + status = "okay"; +}; + +&usbotg { + /* + * PHY0 pins are connected to a USB-C socket, but a role switch is not + * implemented: both CC pins are pulled to GND via a 5.1K resistor. + * The VBUS pins power the device, so a fixed peripheral mode + * is the best choice. + * The board can be powered via GPIOs, in this case port0 *can* + * act as a host (with a cable/adapter ignoring CC), as VBUS is + * then provided by the GPIOs. Any user of this setup would + * need to adjust the DT accordingly: dr_mode set to "host", + * enabling OHCI0 and EHCI0. + */ + dr_mode = "peripheral"; + status = "okay"; +}; + +&usbphy { + usb3_vbus-supply = <®_usb_vbus>; + status = "okay"; +};
The BananaPi M4 Berry is a development board using the Allwinner H618 SoC. It comes with the following specs: - Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache) - 2 GiB LPDDR4 DRAM - 8 GiB eMMC flash - AXP313a PMIC - Gigabit Ethernet, using RTL8211 PHY - RTL8821CU USB WiFi chip - HDMI port - 4 * USB 2.0 ports, via an on-board hub chip - microSD card slot - 3.5mm A/V port - power supply and USB-OTG via USB-C connector Add a devicetree file describing the components that we already have bindings for, that excludes audio and video at the moment. Signed-off-by: Andre Przywara <andre.przywara@arm.com> --- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../sun50i-h618-bananapi-m4-berry.dts | 223 ++++++++++++++++++ 2 files changed, 224 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts