| Message ID | 20240208110602.931573-3-b-kapoor@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | arm64: dts: ti: Modify pinmux for wakeup and mcu uart | expand |
On 08/02/24 16:36, Bhavya Kapoor wrote: > Only Tx and Rx Signal lines for wake up uart are brought out on Please be consistent when referring to instance names s/wake up uart/wkup_uart0 applies to $subject and in commit msg (same issue in patch 3/3 too) > the Common Proc Board through SoM, but CTS and RTS signal lines > are not brought on the board. Thus, remove pinmux for CTS and RTS > signal lines for wake up uart in J721S2. > > Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com> > --- > arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts | 2 -- > 1 file changed, 2 deletions(-) > > diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts > index 361365bb5523..6371cb1c1fe7 100644 > --- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts > +++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts > @@ -190,8 +190,6 @@ J721S2_IOPAD(0x038, PIN_OUTPUT, 0) /* (AB28) MCASP0_ACLKX.MCAN5_TX */ > &wkup_pmx2 { > wkup_uart0_pins_default: wkup-uart0-default-pins { > pinctrl-single,pins = < > - J721S2_WKUP_IOPAD(0x070, PIN_INPUT, 0) /* (E25) WKUP_GPIO0_6.WKUP_UART0_CTSn */ > - J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (F28) WKUP_GPIO0_7.WKUP_UART0_RTSn */ > J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (D28) WKUP_UART0_RXD */ > J721S2_WKUP_IOPAD(0x04c, PIN_OUTPUT, 0) /* (D27) WKUP_UART0_TXD */ > >;
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts index 361365bb5523..6371cb1c1fe7 100644 --- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts +++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts @@ -190,8 +190,6 @@ J721S2_IOPAD(0x038, PIN_OUTPUT, 0) /* (AB28) MCASP0_ACLKX.MCAN5_TX */ &wkup_pmx2 { wkup_uart0_pins_default: wkup-uart0-default-pins { pinctrl-single,pins = < - J721S2_WKUP_IOPAD(0x070, PIN_INPUT, 0) /* (E25) WKUP_GPIO0_6.WKUP_UART0_CTSn */ - J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (F28) WKUP_GPIO0_7.WKUP_UART0_RTSn */ J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (D28) WKUP_UART0_RXD */ J721S2_WKUP_IOPAD(0x04c, PIN_OUTPUT, 0) /* (D27) WKUP_UART0_TXD */ >;
Only Tx and Rx Signal lines for wake up uart are brought out on the Common Proc Board through SoM, but CTS and RTS signal lines are not brought on the board. Thus, remove pinmux for CTS and RTS signal lines for wake up uart in J721S2. Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com> --- arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts | 2 -- 1 file changed, 2 deletions(-)