diff mbox series

[3/4] arm64: dts: rockchip: add RK3588-Q7 (Tiger) SoM

Message ID 20240227164659.705271-4-heiko@sntech.de (mailing list archive)
State New, archived
Headers show
Series Add support for Theobroma-Systems Tiger SoM | expand

Commit Message

Heiko Stuebner Feb. 27, 2024, 4:46 p.m. UTC
From: Heiko Stuebner <heiko.stuebner@cherry.de>

The RK3588-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3588.

It provides the following feature set:
 * up to 16GB LPDDR4x
 * on-module eMMC
 * SD card (on a baseboard) via edge connector
 * Gigabit Ethernet with on-module GbE PHY
 * HDMI/eDP
 * MIPI-DSI
 * 4x MIPI-CSI (3x on FPC connectors, 1x over Q7)
 * HDMI input over FPC connector
 * CAN
 * USB
   - 1x USB 3.0 dual-role (direct connection)
   - 2x USB 3.0 host + 1x USB 2.0 host
 * PCIe
   - 1x PCIe 2.1 Gen3, 4 lanes
   - 2xSATA / 2x PCIe 2.1 Gen1, 2 lanes
 * on-module ATtiny816 companion controller, implementing:
   - low-power RTC functionality (ISL1208 emulation)
   - fan controller (AMC6821 emulation)
 * on-module Secure Element with Global Platform 2.2.1 compliant
   JavaCard environment

Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
---
 .../arm64/boot/dts/rockchip/rk3588-tiger.dtsi | 691 ++++++++++++++++++
 1 file changed, 691 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-tiger.dtsi

Comments

Quentin Schulz Feb. 28, 2024, 11:14 a.m. UTC | #1
Hi Heiko,

On 2/27/24 17:46, Heiko Stuebner wrote:
> From: Heiko Stuebner <heiko.stuebner@cherry.de>
> 
> The RK3588-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
> connector) system-on-module from Theobroma Systems, featuring the
> Rockchip RK3588.
> 
> It provides the following feature set:
>   * up to 16GB LPDDR4x
>   * on-module eMMC
>   * SD card (on a baseboard) via edge connector
>   * Gigabit Ethernet with on-module GbE PHY
>   * HDMI/eDP
>   * MIPI-DSI
>   * 4x MIPI-CSI (3x on FPC connectors, 1x over Q7)
>   * HDMI input over FPC connector
>   * CAN
>   * USB
>     - 1x USB 3.0 dual-role (direct connection)
>     - 2x USB 3.0 host + 1x USB 2.0 host
>   * PCIe
>     - 1x PCIe 2.1 Gen3, 4 lanes
>     - 2xSATA / 2x PCIe 2.1 Gen1, 2 lanes
>   * on-module ATtiny816 companion controller, implementing:
>     - low-power RTC functionality (ISL1208 emulation)
>     - fan controller (AMC6821 emulation)
>   * on-module Secure Element with Global Platform 2.2.1 compliant
>     JavaCard environment
> 
> Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>

Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>

Thanks,
Quentin
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/rockchip/rk3588-tiger.dtsi b/arch/arm64/boot/dts/rockchip/rk3588-tiger.dtsi
new file mode 100644
index 0000000000000..bb24044e27f2c
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588-tiger.dtsi
@@ -0,0 +1,691 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2023 Theobroma Systems Design und Consulting GmbH
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3588.dtsi"
+
+/ {
+	compatible = "tsd,rk3588-tiger", "rockchip,rk3588";
+
+	aliases {
+		mmc0 = &sdhci;
+		rtc0 = &rtc_twi;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		pinctrl-0 = <&emmc_reset>;
+		pinctrl-names = "default";
+		reset-gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&module_led_pin>;
+
+		/* Named LED1 on the board */
+		led-1 {
+			gpios = <&gpio1 RK_PD3 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_HEARTBEAT;
+			linux,default-trigger = "heartbeat";
+			color = <LED_COLOR_ID_AMBER>;
+		};
+	};
+
+	/*
+	 * 100MHz reference clock for PCIe peripherals from PI6C557-05BLE
+	 * clock generator.
+	 * The clock output is gated via the OE pin on the clock generator.
+	 * This is modeled as a fixed-clock plus a gpio-gate-clock.
+	 */
+	pcie_refclk_gen: pcie-refclk-gen-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <1000000000>;
+	};
+
+	pcie_refclk: pcie-refclk-clock {
+		compatible = "gpio-gate-clock";
+		clocks = <&pcie_refclk_gen>;
+		#clock-cells = <0>;
+		enable-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>; /* PCIE30X4_CLKREQN_M1_L */
+	};
+
+	vcc_1v1_nldo_s3: vcc-1v1-nldo-s3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v1_nldo_s3";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc_1v2_s3: vcc-1v2-s3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v2_s3";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_baseboard>;
+	};
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b2 {
+	cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_b3 {
+	cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&gmac0 {
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy>;
+	phy-mode = "rgmii";
+	phy-supply = <&vcc_1v2_s3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_miim
+		     &gmac0_rx_bus2
+		     &gmac0_tx_bus2
+		     &gmac0_rgmii_clk
+		     &gmac0_rgmii_bus
+		     &eth0_pins
+		     &eth_reset>;
+	tx_delay = <0x10>;
+	rx_delay = <0x10>;
+	snps,reset-gpio = <&gpio4 RK_PC3 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 100000>;
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1m0_xfer>;
+};
+
+&i2c1m0_xfer {
+	rockchip,pins =
+		/* i2c1_scl_m0 */
+		<0 RK_PB5 9 &pcfg_pull_none_drv_level_0>,
+		/* i2c1_sda_m0 */
+		<0 RK_PB6 9 &pcfg_pull_none_drv_level_0>;
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2m3_xfer>;
+	status = "okay";
+};
+
+&i2c2m3_xfer {
+	rockchip,pins =
+		/* i2c2_scl_m3 */
+		<1 RK_PC5 9 &pcfg_pull_none_drv_level_0>,
+		/* i2c2_sda_m3 */
+		<1 RK_PC4 9 &pcfg_pull_none_drv_level_0>;
+};
+
+&i2c3 {
+	pinctrl-0 = <&i2c3m0_xfer>;
+};
+
+&i2c4 {
+	pinctrl-0 = <&i2c4m4_xfer>;
+	status = "okay";
+
+	vdd_npu_s0: regulator@42 {
+		compatible = "rockchip,rk8602";
+		reg = <0x42>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_npu_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <950000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c5 {
+	pinctrl-0 = <&i2c5m1_xfer>;
+};
+
+&i2c5m1_xfer {
+	rockchip,pins =
+		/* i2c5_scl_m1 */
+		<4 RK_PB6 9 &pcfg_pull_none_drv_level_0>,
+		/* i2c5_sda_m1 */
+		<4 RK_PB7 9 &pcfg_pull_none_drv_level_0>;
+};
+
+&i2c6 {
+	status = "okay";
+
+	/*
+	 * Mule-ATtiny can handle up to Fast mode Plus (1MHz) on I2C bus,
+	 * but SOC can handle only up to (400kHz).
+	 */
+	clock-frequency = <400000>;
+
+	fan@18 {
+		compatible = "ti,amc6821";
+		reg = <0x18>;
+	};
+
+	rtc_twi: rtc@6f {
+		compatible = "isil,isl1208";
+		reg = <0x6f>;
+	};
+};
+
+&i2c6m0_xfer {
+	rockchip,pins =
+		/* i2c6_scl_m0 */
+		<0 RK_PD0 9 &pcfg_pull_none_drv_level_0>,
+		/* i2c6_sda_m0 */
+		<0 RK_PC7 9 &pcfg_pull_none_drv_level_0>;
+};
+
+&i2c7 {
+	status = "okay";
+
+	vdd_cpu_big0_s0: regulator@42 {
+		compatible = "rockchip,rk8602";
+		reg = <0x42>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu_big0_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_cpu_big1_s0: regulator@43 {
+		compatible = "rockchip,rk8603", "rockchip,rk8602";
+		reg = <0x43>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu_big1_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c7m0_xfer {
+	rockchip,pins =
+		/* i2c7_scl_m0 */
+		<1 RK_PD0 9 &pcfg_pull_none_drv_level_0>,
+		/* i2c7_sda_m0 */
+		<1 RK_PD1 9 &pcfg_pull_none_drv_level_0>;
+};
+
+&i2c8 {
+	pinctrl-0 = <&i2c8m2_xfer>;
+};
+
+&mdio0 {
+	rgmii_phy: ethernet-phy@6 {
+		/* KSZ9031 or KSZ9131 */
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x6>;
+		clocks = <&cru REFCLKO25M_ETH0_OUT>;
+	};
+};
+
+&pcie3x4 {
+	/*
+	 * The board has a gpio-controlled "pcie_refclk" generator,
+	 * so add it to the list of clocks.
+	 */
+	clocks = <&cru ACLK_PCIE_4L_MSTR>, <&cru ACLK_PCIE_4L_SLV>,
+		 <&cru ACLK_PCIE_4L_DBI>, <&cru PCLK_PCIE_4L>,
+		 <&cru CLK_PCIE_AUX0>, <&cru CLK_PCIE4L_PIPE>,
+		 <&pcie_refclk>;
+	clock-names = "aclk_mst", "aclk_slv",
+		      "aclk_dbi", "pclk",
+		      "aux", "pipe",
+		      "ref";
+	reset-gpios = <&gpio3 RK_PB6 GPIO_ACTIVE_HIGH>;
+};
+
+&pinctrl {
+	emmc {
+		emmc_reset: emmc-reset {
+			rockchip,pins = <2 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	ethernet {
+		eth_reset: eth-reset {
+			rockchip,pins = <4 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		module_led_pin: module-led-pin {
+			rockchip,pins = <1 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&saradc {
+	vref-supply = <&vcc_1v8_s0>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	mmc-pwrseq = <&emmc_pwrseq>;
+	no-sdio;
+	no-sd;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk &emmc_data_strobe>;
+	supports-cqe;
+	vmmc-supply = <&vcc_3v3_s3>;
+	vqmmc-supply = <&vcc_1v8_s3>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <150000000>;
+	vqmmc-supply = <&vccio_sd_s0>;
+};
+
+&spi0 {
+	pinctrl-0 = <&spi0m1_cs0 &spi0m1_cs1 &spi0m3_pins>;
+};
+
+&spi2 {
+	assigned-clocks = <&cru CLK_SPI2>;
+	assigned-clock-rates = <200000000>;
+	num-cs = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
+	status = "okay";
+
+	pmic@0 {
+		compatible = "rockchip,rk806";
+		reg = <0x0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+		spi-max-frequency = <1000000>;
+		system-power-controller;
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc5-supply = <&vcc5v0_sys>;
+		vcc6-supply = <&vcc5v0_sys>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc5v0_sys>;
+		vcc9-supply = <&vcc5v0_sys>;
+		vcc10-supply = <&vcc5v0_sys>;
+		vcc11-supply = <&vcc_2v0_pldo_s3>;
+		vcc12-supply = <&vcc5v0_sys>;
+		vcc13-supply = <&vcc_1v1_nldo_s3>;
+		vcc14-supply = <&vcc_1v1_nldo_s3>;
+		vcca-supply = <&vcc5v0_sys>;
+
+		rk806_dvs1_null: dvs1-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs2_null: dvs2-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs3_null: dvs3-null-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun0";
+		};
+
+		regulators {
+			vdd_gpu_s0: dcdc-reg1 {
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_gpu_s0";
+				regulator-enable-ramp-delay = <400>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_lit_s0: dcdc-reg2 {
+				regulator-name = "vdd_cpu_lit_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_log_s0: dcdc-reg3 {
+				regulator-name = "vdd_log_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <675000>;
+				regulator-max-microvolt = <750000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdd_vdenc_s0: dcdc-reg4 {
+				regulator-name = "vdd_vdenc_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_ddr_s0: dcdc-reg5 {
+				regulator-name = "vdd_ddr_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <675000>;
+				regulator-max-microvolt = <900000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			vdd2_ddr_s3: dcdc-reg6 {
+				regulator-name = "vdd2_ddr_s3";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_2v0_pldo_s3: dcdc-reg7 {
+				regulator-name = "vcc_2v0_pldo_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <2000000>;
+				};
+			};
+
+			vcc_3v3_s3: dcdc-reg8 {
+				regulator-name = "vcc_3v3_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vddq_ddr_s0: dcdc-reg9 {
+				regulator-name = "vddq_ddr_s0";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8_s3: dcdc-reg10 {
+				regulator-name = "vcc_1v8_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca_1v8_s0: pldo-reg1 {
+				regulator-name = "vcca_1v8_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8_s0: pldo-reg2 {
+				regulator-name = "vcc_1v8_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdda_1v2_s0: pldo-reg3 {
+				regulator-name = "vdda_1v2_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_3v3_s0: pldo-reg4 {
+				regulator-name = "vcca_3v3_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd_s0: pldo-reg5 {
+				regulator-name = "vccio_sd_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			pldo6_s3: pldo-reg6 {
+				regulator-name = "pldo6_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_0v75_s3: nldo-reg1 {
+				regulator-name = "vdd_0v75_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdda_ddr_pll_s0: nldo-reg2 {
+				regulator-name = "vdda_ddr_pll_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			vdda_0v75_s0: nldo-reg3 {
+				regulator-name = "vdda_0v75_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v85_s0: nldo-reg4 {
+				regulator-name = "vdda_0v85_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_0v75_s0: nldo-reg5 {
+				regulator-name = "vdd_0v75_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&tsadc {
+	status = "okay";
+};
+
+/* Mule-ATtiny UPDI */
+&uart4 {
+	pinctrl-0 = <&uart4m2_xfer>;
+	status = "okay";
+};