diff mbox series

[v2] ARM: dts: imx27-phytec: Add USB support

Message ID 20240328-pca100-v2-1-d7ff1679f75b@pengutronix.de (mailing list archive)
State New, archived
Headers show
Series [v2] ARM: dts: imx27-phytec: Add USB support | expand

Commit Message

Michael Grzeschik April 3, 2024, 8:18 a.m. UTC 
This patch adds the pinmux and nodes for usbotg and usbh2.

In v6 revision of the pca100 the usb phys were changed to usb3320 which
are connected by their reset pins. We add the phy configuration to the
description.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
---
Changes in v2:
- changed prefix to "ARM: dts: imx27-phytec:"
- Link to v1: https://lore.kernel.org/r/20240328-pca100-v1-1-58df67c2c950@pengutronix.de
---
 .../dts/nxp/imx/imx27-phytec-phycard-s-som.dtsi    | 78 ++++++++++++++++++++++
 1 file changed, 78 insertions(+)


---
base-commit: 5bab5dc780c9ed0c69fc2f828015532acf4a7848
change-id: 20240328-pca100-a600ac4384e7

Best regards,

Comments

Shawn Guo April 22, 2024, 3:31 a.m. UTC | #1 
On Wed, Apr 03, 2024 at 10:18:27AM +0200, Michael Grzeschik wrote:
> This patch adds the pinmux and nodes for usbotg and usbh2.
> 
> In v6 revision of the pca100 the usb phys were changed to usb3320 which
> are connected by their reset pins. We add the phy configuration to the
> description.
> 
> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>

Applied, thanks!
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycard-s-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycard-s-som.dtsi
index abc9233c5a1b1..31b3fc972abbf 100644
--- a/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycard-s-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycard-s-som.dtsi
@@ -15,6 +15,22 @@  memory@a0000000 {
 		device_type = "memory";
 		reg = <0xa0000000 0x08000000>; /* 128MB */
 	};
+
+	usbotgphy: usbotgphy {
+		compatible = "usb-nop-xceiv";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotgphy>;
+		reset-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>;
+		#phy-cells = <0>;
+	};
+
+	usbh2phy: usbh2phy {
+		compatible = "usb-nop-xceiv";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh2phy>;
+		reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
+		#phy-cells = <0>;
+	};
 };
 
 &cspi1 {
@@ -84,6 +100,52 @@  MX27_PAD_NFRE_B__NFRE_B 0x0
 				MX27_PAD_NFWE_B__NFWE_B 0x0
 			>;
 		};
+
+		pinctrl_usbotgphy: usbotgphygrp {
+			fsl,pins = <
+				MX27_PAD_USBH1_RCV__GPIO2_25		0x1 /* reset gpio */
+			>;
+		};
+
+		pinctrl_usbotg: usbotggrp {
+			fsl,pins = <
+				MX27_PAD_USBOTG_CLK__USBOTG_CLK		0x0
+				MX27_PAD_USBOTG_DIR__USBOTG_DIR		0x0
+				MX27_PAD_USBOTG_NXT__USBOTG_NXT		0x0
+				MX27_PAD_USBOTG_STP__USBOTG_STP		0x0
+				MX27_PAD_USBOTG_DATA0__USBOTG_DATA0	0x0
+				MX27_PAD_USBOTG_DATA1__USBOTG_DATA1	0x0
+				MX27_PAD_USBOTG_DATA2__USBOTG_DATA2	0x0
+				MX27_PAD_USBOTG_DATA3__USBOTG_DATA3	0x0
+				MX27_PAD_USBOTG_DATA4__USBOTG_DATA4	0x0
+				MX27_PAD_USBOTG_DATA5__USBOTG_DATA5	0x0
+				MX27_PAD_USBOTG_DATA6__USBOTG_DATA6	0x0
+				MX27_PAD_USBOTG_DATA7__USBOTG_DATA7	0x0
+			>;
+		};
+
+		pinctrl_usbh2phy: usbh2phygrp {
+			fsl,pins = <
+				MX27_PAD_USBH1_SUSP__GPIO2_22		0x0 /* reset gpio */
+			>;
+		};
+
+		pinctrl_usbh2: usbh2grp {
+			fsl,pins = <
+				MX27_PAD_USBH2_CLK__USBH2_CLK		0x0
+				MX27_PAD_USBH2_DIR__USBH2_DIR		0x0
+				MX27_PAD_USBH2_NXT__USBH2_NXT		0x0
+				MX27_PAD_USBH2_STP__USBH2_STP		0x0
+				MX27_PAD_CSPI2_SCLK__USBH2_DATA0	0x0
+				MX27_PAD_CSPI2_MOSI__USBH2_DATA1	0x0
+				MX27_PAD_CSPI2_MISO__USBH2_DATA2	0x0
+				MX27_PAD_CSPI2_SS1__USBH2_DATA3		0x0
+				MX27_PAD_CSPI2_SS2__USBH2_DATA4		0x0
+				MX27_PAD_CSPI1_SS2__USBH2_DATA5		0x0
+				MX27_PAD_CSPI2_SS0__USBH2_DATA6		0x0
+				MX27_PAD_USBH2_DATA7__USBH2_DATA7	0x0
+			>;
+		};
 	};
 };
 
@@ -95,3 +157,19 @@  &nfc {
 	nand-on-flash-bbt;
 	status = "okay";
 };
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "ulpi";
+	phys = <&usbotgphy>;
+	status = "okay";
+};
+
+&usbh2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh2>;
+	phy_type = "ulpi";
+	phys = <&usbh2phy>;
+	status = "okay";
+};