diff mbox series

[v2,3/3] arm64: dts: freescale: Add device tree for Emcraft Systems NavQ+ Kit

Message ID 20240330133410.41408-4-gilles.talis@gmail.com (mailing list archive)
State New, archived
Headers show
Series Add support for Emcraft Systems NavQ+ kit | expand

Commit Message

Gilles Talis March 30, 2024, 1:34 p.m. UTC 
The Emcraft Systems NavQ+ kit is a mobile robotics platform
based on NXP i.MX8 MPlus SoC.

The following interfaces and devices are enabled:
- eMMC
- Gigabit Ethernet
- RTC
- SD-Card
- UART console

Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../arm64/boot/dts/freescale/imx8mp-navqp.dts | 424 ++++++++++++++++++
 2 files changed, 425 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-navqp.dts

Comments

Andrew Lunn March 30, 2024, 4:46 p.m. UTC | #1 
> +&eqos {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_eqos>;
> +	phy-mode = "rgmii-id";
> +	phy-handle = <&ethphy0>;
> +	status = "okay";
> +
> +	mdio {
> +		compatible = "snps,dwmac-mdio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy0: ethernet-phy@0 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <0>;
> +			reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
> +			reset-assert-us = <1000>;
> +			reset-deassert-us = <10000>;
> +			qca,disable-smarteee;
> +			qca,disable-hibernation-mode;
> +		};
> +	};
> +};

Thanks for removing the regulator.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew
Fabio Estevam March 30, 2024, 5:03 p.m. UTC | #2 
Hi Gilles,

On Sat, Mar 30, 2024 at 10:34 AM Gilles Talis <gilles.talis@gmail.com> wrote:
>
> The Emcraft Systems NavQ+ kit is a mobile robotics platform
> based on NXP i.MX8 MPlus SoC.
>
> The following interfaces and devices are enabled:
> - eMMC
> - Gigabit Ethernet
> - RTC
> - SD-Card
> - UART console
>
> Signed-off-by: Gilles Talis <gilles.talis@gmail.com>

Reviewed-by: Fabio Estevam <festevam@gmail.com>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 045250d0a040..bf99864c0bc4 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -166,6 +166,7 @@  dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-icore-mx8mp-edimm2.2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-msc-sm2s-ep1.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-navqp.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-hdmi.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-lt6.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-navqp.dts b/arch/arm64/boot/dts/freescale/imx8mp-navqp.dts
new file mode 100644
index 000000000000..5fd1614982cd
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-navqp.dts
@@ -0,0 +1,424 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2021 Emcraft Systems
+ * Copyright 2024 Gilles Talis <gilles.talis@gmail.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx8mp.dtsi"
+
+/ {
+	model = "Emcraft Systems i.MX8MPlus NavQ+ Kit";
+	compatible = "emcraft,imx8mp-navqp", "fsl,imx8mp";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_led>;
+
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+		off-on-delay-us = <12000>;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck2>;
+};
+
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <10000>;
+			qca,disable-smarteee;
+			qca,disable-hibernation-mode;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pmic@25 {
+		compatible = "nxp,pca9450c";
+		reg = <0x25>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			BUCK1 {
+				regulator-name = "BUCK1";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <2187500>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			buck2: BUCK2 {
+				regulator-name = "BUCK2";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <2187500>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+			};
+
+			BUCK4 {
+				regulator-name = "BUCK4";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			BUCK5 {
+				regulator-name = "BUCK5";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			BUCK6 {
+				regulator-name = "BUCK6";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO3 {
+				regulator-name = "LDO3";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO4 {
+				regulator-name = "LDO4";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO5 {
+				regulator-name = "LDO5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	rtc@53 {
+		compatible = "nxp,pcf2131";
+		reg = <0x53>;
+	};
+};
+
+&uart2 {
+	/* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+/* SD Card */
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+/* eMMC */
+&usdhc3 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
+	assigned-clock-rates = <400000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_eqos: eqosgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC				0x3
+			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO				0x3
+			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0			0x91
+			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1			0x91
+			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2			0x91
+			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3			0x91
+			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x91
+			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL			0x91
+			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0			0x1f
+			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1			0x1f
+			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2			0x1f
+			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3			0x1f
+			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL			0x1f
+			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x1f
+			MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22				0x110
+		>;
+	};
+
+	pinctrl_gpio_led: gpioledgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16				0x19
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL					0x400001c3
+			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA					0x400001c3
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL					0x400001c3
+			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA					0x400001c3
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL					0x400001c3
+			MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA					0x400001c3
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL					0x400001c3
+			MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA					0x400001c3
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03				0x41
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19				0x41
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX				0x49
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX				0x49
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK				0x190
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD				0x1d0
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0				0x1d0
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1				0x1d0
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2				0x1d0
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3				0x1d0
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT				0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK				0x194
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD				0x1d4
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0				0x1d4
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1				0x1d4
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2				0x1d4
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3				0x1d4
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT				0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK				0x196
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD				0x1d6
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0				0x1d6
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1				0x1d6
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2				0x1d6
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3				0x1d6
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT				0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12				0x1c4
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK				0x190
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD				0x1d0
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0				0x1d0
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1				0x1d0
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2				0x1d0
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3				0x1d0
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4				0x1d0
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5				0x1d0
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6				0x1d0
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7				0x1d0
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE				0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK				0x194
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD				0x1d4
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0				0x1d4
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1				0x1d4
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2				0x1d4
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3				0x1d4
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4				0x1d4
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5				0x1d4
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6				0x1d4
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7				0x1d4
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE				0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK				0x196
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD				0x1d6
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0				0x1d6
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1				0x1d6
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2				0x1d6
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3				0x1d6
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4				0x1d6
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5				0x1d6
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6				0x1d6
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7				0x1d6
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE				0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B				0xc6
+		>;
+	};
+};