@@ -30,7 +30,7 @@ memory@0 {
reg = <0x0 0x0 0x0 0x80000000>;
};
- ap0_reg_sd_vccq: ap0_sd_vccq@0 {
+ ap0_reg_sd_vccq: regulator-1 {
compatible = "regulator-gpio";
regulator-name = "ap0_sd_vccq";
regulator-min-microvolt = <1800000>;
@@ -39,7 +39,7 @@ ap0_reg_sd_vccq: ap0_sd_vccq@0 {
states = <1800000 0x1 3300000 0x0>;
};
- cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 {
+ cp0_reg_usb3_vbus0: regulator-2 {
compatible = "regulator-fixed";
regulator-name = "cp0-xhci0-vbus";
regulator-min-microvolt = <5000000>;
@@ -48,12 +48,12 @@ cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 {
gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
};
- cp0_usb3_0_phy0: cp0_usb3_phy@0 {
+ cp0_usb3_0_phy0: usb-phy-1 {
compatible = "usb-nop-xceiv";
vcc-supply = <&cp0_reg_usb3_vbus0>;
};
- cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 {
+ cp0_reg_usb3_vbus1: regulator-3 {
compatible = "regulator-fixed";
regulator-name = "cp0-xhci1-vbus";
regulator-min-microvolt = <5000000>;
@@ -62,12 +62,12 @@ cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 {
gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
};
- cp0_usb3_0_phy1: cp0_usb3_phy@1 {
+ cp0_usb3_0_phy1: usb-phy-2 {
compatible = "usb-nop-xceiv";
vcc-supply = <&cp0_reg_usb3_vbus1>;
};
- cp0_reg_sd_vccq: cp0_sd_vccq@0 {
+ cp0_reg_sd_vccq: regulator-4 {
compatible = "regulator-gpio";
regulator-name = "cp0_sd_vccq";
regulator-min-microvolt = <1800000>;
@@ -77,7 +77,7 @@ cp0_reg_sd_vccq: cp0_sd_vccq@0 {
3300000 0x0>;
};
- cp0_reg_sd_vcc: cp0_sd_vcc@0 {
+ cp0_reg_sd_vcc: regulator-5 {
compatible = "regulator-fixed";
regulator-name = "cp0_sd_vcc";
regulator-min-microvolt = <3300000>;
@@ -87,7 +87,7 @@ cp0_reg_sd_vcc: cp0_sd_vcc@0 {
regulator-always-on;
};
- cp0_sfp_eth0: sfp-eth@0 {
+ cp0_sfp_eth0: sfp-eth-1 {
compatible = "sff,sfp";
i2c-bus = <&cp0_sfpp0_i2c>;
los-gpios = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>;
@@ -18,7 +18,7 @@ aliases {
ethernet4 = &cp1_eth1;
};
- cp1_reg_usb3_vbus0: cp1_usb3_vbus@0 {
+ cp1_reg_usb3_vbus0: regulator-6 {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&cp1_xhci0_vbus_pins>;
@@ -29,12 +29,12 @@ cp1_reg_usb3_vbus0: cp1_usb3_vbus@0 {
gpio = <&cp1_gpio1 3 GPIO_ACTIVE_HIGH>;
};
- cp1_usb3_0_phy0: cp1_usb3_phy0 {
+ cp1_usb3_0_phy0: usb-phy-3 {
compatible = "usb-nop-xceiv";
vcc-supply = <&cp1_reg_usb3_vbus0>;
};
- cp1_sfp_eth1: sfp-eth1 {
+ cp1_sfp_eth1: sfp-eth-2 {
compatible = "sff,sfp";
i2c-bus = <&cp1_i2c0>;
los-gpios = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>;
@@ -17,7 +17,7 @@ aliases {
ethernet5 = &cp2_eth0;
};
- cp2_reg_usb3_vbus0: cp2_usb3_vbus@0 {
+ cp2_reg_usb3_vbus0: regulator-7 {
compatible = "regulator-fixed";
regulator-name = "cp2-xhci0-vbus";
regulator-min-microvolt = <5000000>;
@@ -26,12 +26,12 @@ cp2_reg_usb3_vbus0: cp2_usb3_vbus@0 {
gpio = <&cp2_gpio1 2 GPIO_ACTIVE_HIGH>;
};
- cp2_usb3_0_phy0: cp2_usb3_phy0 {
+ cp2_usb3_0_phy0: usb-phy-4 {
compatible = "usb-nop-xceiv";
vcc-supply = <&cp2_reg_usb3_vbus0>;
};
- cp2_reg_usb3_vbus1: cp2_usb3_vbus@1 {
+ cp2_reg_usb3_vbus1: regulator-8 {
compatible = "regulator-fixed";
regulator-name = "cp2-xhci1-vbus";
regulator-min-microvolt = <5000000>;
@@ -40,12 +40,12 @@ cp2_reg_usb3_vbus1: cp2_usb3_vbus@1 {
gpio = <&cp2_gpio1 3 GPIO_ACTIVE_HIGH>;
};
- cp2_usb3_0_phy1: cp2_usb3_phy1 {
+ cp2_usb3_0_phy1: usb-phy-5 {
compatible = "usb-nop-xceiv";
vcc-supply = <&cp2_reg_usb3_vbus1>;
};
- cp2_reg_sd_vccq: cp2_sd_vccq@0 {
+ cp2_reg_sd_vccq: regulator-9 {
compatible = "regulator-gpio";
regulator-name = "cp2_sd_vcc";
regulator-min-microvolt = <1800000>;
@@ -54,7 +54,7 @@ cp2_reg_sd_vccq: cp2_sd_vccq@0 {
states = <1800000 0x1 3300000 0x0>;
};
- cp2_sfp_eth0: sfp-eth0 {
+ cp2_sfp_eth0: sfp-eth-3 {
compatible = "sff,sfp";
i2c-bus = <&cp2_sfpp0_i2c>;
los-gpios = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>;
Top-level nodes, not being on MMIO bus, do not have "reg" properties and should not have unit addresses. Correct their name as well to match "Generic node names" recommendation from Devicetree specification. This also fixes dtc W=1 warnings: cn9130-db.dtsi:28.11-31.4: Warning (unique_unit_address_if_enabled): /memory@0: duplicate unit-address (also used in node /ap0_sd_vccq@0) cn9130-db.dtsi:28.11-31.4: Warning (unique_unit_address_if_enabled): /memory@0: duplicate unit-address (also used in node /cp0_usb3_vbus@0) cn9130-db.dtsi:33.33-40.4: Warning (unique_unit_address_if_enabled): /ap0_sd_vccq@0: duplicate unit-address (also used in node /cp0_usb3_vbus@0) cn9130-db.dtsi:28.11-31.4: Warning (unique_unit_address_if_enabled): /memory@0: duplicate unit-address (also used in node /cp0_usb3_phy@0) cn9130-db.dtsi:33.33-40.4: Warning (unit_address_vs_reg): /ap0_sd_vccq@0: node has a unit name, but no reg or ranges property cn9130-db.dtsi:42.38-49.4: Warning (unit_address_vs_reg): /cp0_usb3_vbus@0: node has a unit name, but no reg or ranges property cn9130-db.dtsi:51.34-54.4: Warning (unit_address_vs_reg): /cp0_usb3_phy@0: node has a unit name, but no reg or ranges property cn9130-db.dtsi:56.38-63.4: Warning (unit_address_vs_reg): /cp0_usb3_vbus@1: node has a unit name, but no reg or ranges property Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> --- arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 16 ++++++++-------- arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 6 +++--- arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 12 ++++++------ 3 files changed, 17 insertions(+), 17 deletions(-)