@@ -127,12 +127,70 @@ &lpi2c7 {
pinctrl-1 = <&pinctrl_lpi2c7>;
status = "okay";
+ ptn5150_1: typec@1d {
+ compatible = "nxp,ptn5150";
+ reg = <0x1d>;
+ int-gpios = <&gpiof 3 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_typec1>;
+ status = "disabled";
+ };
+
pcal6408: gpio@21 {
compatible = "nxp,pcal9554b";
reg = <0x21>;
gpio-controller;
#gpio-cells = <2>;
};
+
+ ptn5150_2: typec@3d {
+ compatible = "nxp,ptn5150";
+ reg = <0x3d>;
+ int-gpios = <&gpiof 5 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_typec2>;
+ status = "disabled";
+ };
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1>;
+ dr_mode = "otg";
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ over-current-active-low;
+ status = "okay";
+};
+
+&usbphy1 {
+ fsl,tx-d-cal = <110>;
+ status = "okay";
+};
+
+&usbmisc1 {
+ status = "okay";
+};
+
+&usbotg2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb2>;
+ dr_mode = "otg";
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ over-current-active-low;
+ status = "okay";
+};
+
+&usbphy2 {
+ fsl,tx-d-cal = <110>;
+ status = "okay";
+};
+
+&usbmisc2 {
+ status = "okay";
};
&usdhc0 {
@@ -224,6 +282,32 @@ MX8ULP_PAD_PTE13__LPI2C7_SDA 0x20
>;
};
+ pinctrl_typec1: typec1grp {
+ fsl,pins = <
+ MX8ULP_PAD_PTF3__PTF3 0x3
+ >;
+ };
+
+ pinctrl_typec2: typec2grp {
+ fsl,pins = <
+ MX8ULP_PAD_PTF5__PTF5 0x3
+ >;
+ };
+
+ pinctrl_usb1: usb1grp {
+ fsl,pins = <
+ MX8ULP_PAD_PTF2__USB0_ID 0x10003
+ MX8ULP_PAD_PTF4__USB0_OC 0x10003
+ >;
+ };
+
+ pinctrl_usb2: usb2grp {
+ fsl,pins = <
+ MX8ULP_PAD_PTD23__USB1_ID 0x10003
+ MX8ULP_PAD_PTF6__USB1_OC 0x10003
+ >;
+ };
+
pinctrl_usdhc0: usdhc0grp {
fsl,pins = <
MX8ULP_PAD_PTD1__SDHC0_CMD 0x3
Enable 2 USB nodes and add 2 PTN5150 nodes on i.MX8ULP evk board. Signed-off-by: Xu Yang <xu.yang_2@nxp.com> --- Changes in v2: - fix format as suggusted by Fabio - add PTN5150 nodes Changes in v3: - no changes Changes in v4: - no changes Changes in v5: - no changes Changes in v6: - no changes Changes in v7: - no changes Changes in v8: - no changes Changes in v9: - no changes Changes in v10: - no changes Changes in v11: - fix indent - adjust order --- arch/arm64/boot/dts/freescale/imx8ulp-evk.dts | 84 +++++++++++++++++++ 1 file changed, 84 insertions(+)