diff mbox series

[v3,1/2] dt-bindings: net: bluetooth: Add MediaTek MT7921S SDIO Bluetooth

Message ID 20240412073046.1192744-2-wenst@chromium.org (mailing list archive)
State Accepted
Headers show
Series bluetooth: mt7921s: Add binding and fixup existing dts | expand

Commit Message

Chen-Yu Tsai April 12, 2024, 7:30 a.m. UTC 
The MediaTek MT7921S is a WiFi/Bluetooth combo chip that works over
SDIO. WiFi and Bluetooth are separate SDIO functions within the chip.
While the Bluetooth SDIO function is fully discoverable, the chip has
a pin that can reset just the Bluetooth core, as opposed to the full
chip. This should be described in the device tree.

Add a device tree binding for the Bluetooth SDIO function of the MT7921S
specifically to document the reset line. This binding is based on the MMC
controller binding, which specifies one device node per SDIO function.

Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
---
Changes since v2:
- Expand description and commit message to clearly state that WiFi and
  Bluetooth are separate SDIO functions, and that each function should
  be a separate device node, as specified by the MMC binding.
- Change 'additionalProperties' to 'unevaluatedProperties'
- Add missing separating new line
- s/ot/to/

Angelo's reviewed-by was not picked up due to the above changes.

Changes since v1:
- Reworded descriptions
- Moved binding maintainer section before description
- Added missing reference to bluetooth-controller.yaml
- Added missing GPIO header to example
---
 .../bluetooth/mediatek,mt7921s-bluetooth.yaml | 55 +++++++++++++++++++
 MAINTAINERS                                   |  1 +
 2 files changed, 56 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml

Comments

AngeloGioacchino Del Regno April 15, 2024, 8 a.m. UTC | #1 
Il 12/04/24 09:30, Chen-Yu Tsai ha scritto:
> The MediaTek MT7921S is a WiFi/Bluetooth combo chip that works over
> SDIO. WiFi and Bluetooth are separate SDIO functions within the chip.
> While the Bluetooth SDIO function is fully discoverable, the chip has
> a pin that can reset just the Bluetooth core, as opposed to the full
> chip. This should be described in the device tree.
> 
> Add a device tree binding for the Bluetooth SDIO function of the MT7921S
> specifically to document the reset line. This binding is based on the MMC
> controller binding, which specifies one device node per SDIO function.
> 
> Cc: Sean Wang <sean.wang@mediatek.com>
> Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Rob Herring April 15, 2024, 11:05 p.m. UTC | #2 
On Fri, 12 Apr 2024 15:30:42 +0800, Chen-Yu Tsai wrote:
> The MediaTek MT7921S is a WiFi/Bluetooth combo chip that works over
> SDIO. WiFi and Bluetooth are separate SDIO functions within the chip.
> While the Bluetooth SDIO function is fully discoverable, the chip has
> a pin that can reset just the Bluetooth core, as opposed to the full
> chip. This should be described in the device tree.
> 
> Add a device tree binding for the Bluetooth SDIO function of the MT7921S
> specifically to document the reset line. This binding is based on the MMC
> controller binding, which specifies one device node per SDIO function.
> 
> Cc: Sean Wang <sean.wang@mediatek.com>
> Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
> ---
> Changes since v2:
> - Expand description and commit message to clearly state that WiFi and
>   Bluetooth are separate SDIO functions, and that each function should
>   be a separate device node, as specified by the MMC binding.
> - Change 'additionalProperties' to 'unevaluatedProperties'
> - Add missing separating new line
> - s/ot/to/
> 
> Angelo's reviewed-by was not picked up due to the above changes.
> 
> Changes since v1:
> - Reworded descriptions
> - Moved binding maintainer section before description
> - Added missing reference to bluetooth-controller.yaml
> - Added missing GPIO header to example
> ---
>  .../bluetooth/mediatek,mt7921s-bluetooth.yaml | 55 +++++++++++++++++++
>  MAINTAINERS                                   |  1 +
>  2 files changed, 56 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>
Sean Wang April 17, 2024, 11:04 p.m. UTC | #3 
Hi Chen-Yu,

On Fri, Apr 12, 2024 at 12:31 AM Chen-Yu Tsai <wenst@chromium.org> wrote:
>
> The MediaTek MT7921S is a WiFi/Bluetooth combo chip that works over
> SDIO. WiFi and Bluetooth are separate SDIO functions within the chip.
> While the Bluetooth SDIO function is fully discoverable, the chip has
> a pin that can reset just the Bluetooth core, as opposed to the full
> chip. This should be described in the device tree.
>
> Add a device tree binding for the Bluetooth SDIO function of the MT7921S
> specifically to document the reset line. This binding is based on the MMC
> controller binding, which specifies one device node per SDIO function.
>
> Cc: Sean Wang <sean.wang@mediatek.com>
> Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
> ---
> Changes since v2:
> - Expand description and commit message to clearly state that WiFi and
>   Bluetooth are separate SDIO functions, and that each function should
>   be a separate device node, as specified by the MMC binding.
> - Change 'additionalProperties' to 'unevaluatedProperties'
> - Add missing separating new line
> - s/ot/to/
>
> Angelo's reviewed-by was not picked up due to the above changes.
>
> Changes since v1:
> - Reworded descriptions
> - Moved binding maintainer section before description
> - Added missing reference to bluetooth-controller.yaml
> - Added missing GPIO header to example
> ---
>  .../bluetooth/mediatek,mt7921s-bluetooth.yaml | 55 +++++++++++++++++++
>  MAINTAINERS                                   |  1 +
>  2 files changed, 56 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
>
> diff --git a/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml b/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
> new file mode 100644
> index 000000000000..67ff7caad599
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
> @@ -0,0 +1,55 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/bluetooth/mediatek,mt7921s-bluetooth.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: MediaTek MT7921S Bluetooth
> +
> +maintainers:
> +  - Sean Wang <sean.wang@mediatek.com>
> +
> +description:
> +  MT7921S is an SDIO-attached dual-radio WiFi+Bluetooth Combo chip; each
> +  function is its own SDIO function on a shared SDIO interface. The chip
> +  has two dedicated reset lines, one for each function core.
> +  This binding only covers the Bluetooth SDIO function, with one device
> +  node describing only this SDIO function.
> +
> +allOf:
> +  - $ref: bluetooth-controller.yaml#
> +
> +properties:
> +  compatible:
> +    enum:
> +      - mediatek,mt7921s-bluetooth
> +
> +  reg:
> +    const: 2
> +
> +  reset-gpios:
> +    maxItems: 1
> +    description:
> +      An active-low reset line for the Bluetooth core; on typical M.2
> +      key E modules this is the W_DISABLE2# pin.
> +

Thanks for adding the new setup for the MT7921S devices. They look good to me.
Sometimes, the MT7921S might be set up to wake up the host when it's
asleep using a sideband signal.
This might need an extra pin called "wakeup" to make it happen. Can
you help add this pin to the settings in the same update, or should I
do it later?

> +required:
> +  - compatible
> +  - reg
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +
> +    mmc {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        bluetooth@2 {
> +            compatible = "mediatek,mt7921s-bluetooth";
> +            reg = <2>;
> +            reset-gpios = <&pio 8 GPIO_ACTIVE_LOW>;
> +        };
> +    };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 88981d9f3958..218bc2a21207 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -13818,6 +13818,7 @@ M:      Sean Wang <sean.wang@mediatek.com>
>  L:     linux-bluetooth@vger.kernel.org
>  L:     linux-mediatek@lists.infradead.org (moderated for non-subscribers)
>  S:     Maintained
> +F:     Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
>  F:     Documentation/devicetree/bindings/net/mediatek-bluetooth.txt
>  F:     drivers/bluetooth/btmtkuart.c
>
> --
> 2.44.0.683.g7961c838ac-goog
>
>
Chen-Yu Tsai April 17, 2024, 11:31 p.m. UTC | #4 
On Wed, Apr 17, 2024 at 4:04 PM Sean Wang <sean.wang@kernel.org> wrote:
>
> Hi Chen-Yu,
>
> On Fri, Apr 12, 2024 at 12:31 AM Chen-Yu Tsai <wenst@chromium.org> wrote:
> >
> > The MediaTek MT7921S is a WiFi/Bluetooth combo chip that works over
> > SDIO. WiFi and Bluetooth are separate SDIO functions within the chip.
> > While the Bluetooth SDIO function is fully discoverable, the chip has
> > a pin that can reset just the Bluetooth core, as opposed to the full
> > chip. This should be described in the device tree.
> >
> > Add a device tree binding for the Bluetooth SDIO function of the MT7921S
> > specifically to document the reset line. This binding is based on the MMC
> > controller binding, which specifies one device node per SDIO function.
> >
> > Cc: Sean Wang <sean.wang@mediatek.com>
> > Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
> > ---
> > Changes since v2:
> > - Expand description and commit message to clearly state that WiFi and
> >   Bluetooth are separate SDIO functions, and that each function should
> >   be a separate device node, as specified by the MMC binding.
> > - Change 'additionalProperties' to 'unevaluatedProperties'
> > - Add missing separating new line
> > - s/ot/to/
> >
> > Angelo's reviewed-by was not picked up due to the above changes.
> >
> > Changes since v1:
> > - Reworded descriptions
> > - Moved binding maintainer section before description
> > - Added missing reference to bluetooth-controller.yaml
> > - Added missing GPIO header to example
> > ---
> >  .../bluetooth/mediatek,mt7921s-bluetooth.yaml | 55 +++++++++++++++++++
> >  MAINTAINERS                                   |  1 +
> >  2 files changed, 56 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml b/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
> > new file mode 100644
> > index 000000000000..67ff7caad599
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
> > @@ -0,0 +1,55 @@
> > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/net/bluetooth/mediatek,mt7921s-bluetooth.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: MediaTek MT7921S Bluetooth
> > +
> > +maintainers:
> > +  - Sean Wang <sean.wang@mediatek.com>
> > +
> > +description:
> > +  MT7921S is an SDIO-attached dual-radio WiFi+Bluetooth Combo chip; each
> > +  function is its own SDIO function on a shared SDIO interface. The chip
> > +  has two dedicated reset lines, one for each function core.
> > +  This binding only covers the Bluetooth SDIO function, with one device
> > +  node describing only this SDIO function.
> > +
> > +allOf:
> > +  - $ref: bluetooth-controller.yaml#
> > +
> > +properties:
> > +  compatible:
> > +    enum:
> > +      - mediatek,mt7921s-bluetooth
> > +
> > +  reg:
> > +    const: 2
> > +
> > +  reset-gpios:
> > +    maxItems: 1
> > +    description:
> > +      An active-low reset line for the Bluetooth core; on typical M.2
> > +      key E modules this is the W_DISABLE2# pin.
> > +
>
> Thanks for adding the new setup for the MT7921S devices. They look good to me.
> Sometimes, the MT7921S might be set up to wake up the host when it's
> asleep using a sideband signal.
> This might need an extra pin called "wakeup" to make it happen. Can
> you help add this pin to the settings in the same update, or should I
> do it later?

I suggest you send a patch on top of this one? I'm not sure if you
would model it as a GPIO or interrupt. And there doesn't seem to be
any code in the driver expecting it.


ChenYu

> > +required:
> > +  - compatible
> > +  - reg
> > +
> > +unevaluatedProperties: false
> > +
> > +examples:
> > +  - |
> > +    #include <dt-bindings/gpio/gpio.h>
> > +
> > +    mmc {
> > +        #address-cells = <1>;
> > +        #size-cells = <0>;
> > +
> > +        bluetooth@2 {
> > +            compatible = "mediatek,mt7921s-bluetooth";
> > +            reg = <2>;
> > +            reset-gpios = <&pio 8 GPIO_ACTIVE_LOW>;
> > +        };
> > +    };
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 88981d9f3958..218bc2a21207 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -13818,6 +13818,7 @@ M:      Sean Wang <sean.wang@mediatek.com>
> >  L:     linux-bluetooth@vger.kernel.org
> >  L:     linux-mediatek@lists.infradead.org (moderated for non-subscribers)
> >  S:     Maintained
> > +F:     Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
> >  F:     Documentation/devicetree/bindings/net/mediatek-bluetooth.txt
> >  F:     drivers/bluetooth/btmtkuart.c
> >
> > --
> > 2.44.0.683.g7961c838ac-goog
> >
> >
Sean Wang April 17, 2024, 11:41 p.m. UTC | #5 
Hi Chen-Yu,

okay, we will add it once we have implemented it in the driver. thanks
for adding the dt-binding.

     Sean

On Wed, Apr 17, 2024 at 4:32 PM Chen-Yu Tsai <wenst@chromium.org> wrote:
>
> On Wed, Apr 17, 2024 at 4:04 PM Sean Wang <sean.wang@kernel.org> wrote:
> >
> > Hi Chen-Yu,
> >
> > On Fri, Apr 12, 2024 at 12:31 AM Chen-Yu Tsai <wenst@chromium.org> wrote:
> > >
> > > The MediaTek MT7921S is a WiFi/Bluetooth combo chip that works over
> > > SDIO. WiFi and Bluetooth are separate SDIO functions within the chip.
> > > While the Bluetooth SDIO function is fully discoverable, the chip has
> > > a pin that can reset just the Bluetooth core, as opposed to the full
> > > chip. This should be described in the device tree.
> > >
> > > Add a device tree binding for the Bluetooth SDIO function of the MT7921S
> > > specifically to document the reset line. This binding is based on the MMC
> > > controller binding, which specifies one device node per SDIO function.
> > >
> > > Cc: Sean Wang <sean.wang@mediatek.com>
> > > Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
> > > ---
> > > Changes since v2:
> > > - Expand description and commit message to clearly state that WiFi and
> > >   Bluetooth are separate SDIO functions, and that each function should
> > >   be a separate device node, as specified by the MMC binding.
> > > - Change 'additionalProperties' to 'unevaluatedProperties'
> > > - Add missing separating new line
> > > - s/ot/to/
> > >
> > > Angelo's reviewed-by was not picked up due to the above changes.
> > >
> > > Changes since v1:
> > > - Reworded descriptions
> > > - Moved binding maintainer section before description
> > > - Added missing reference to bluetooth-controller.yaml
> > > - Added missing GPIO header to example
> > > ---
> > >  .../bluetooth/mediatek,mt7921s-bluetooth.yaml | 55 +++++++++++++++++++
> > >  MAINTAINERS                                   |  1 +
> > >  2 files changed, 56 insertions(+)
> > >  create mode 100644 Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
> > >
> > > diff --git a/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml b/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
> > > new file mode 100644
> > > index 000000000000..67ff7caad599
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
> > > @@ -0,0 +1,55 @@
> > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/net/bluetooth/mediatek,mt7921s-bluetooth.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: MediaTek MT7921S Bluetooth
> > > +
> > > +maintainers:
> > > +  - Sean Wang <sean.wang@mediatek.com>
> > > +
> > > +description:
> > > +  MT7921S is an SDIO-attached dual-radio WiFi+Bluetooth Combo chip; each
> > > +  function is its own SDIO function on a shared SDIO interface. The chip
> > > +  has two dedicated reset lines, one for each function core.
> > > +  This binding only covers the Bluetooth SDIO function, with one device
> > > +  node describing only this SDIO function.
> > > +
> > > +allOf:
> > > +  - $ref: bluetooth-controller.yaml#
> > > +
> > > +properties:
> > > +  compatible:
> > > +    enum:
> > > +      - mediatek,mt7921s-bluetooth
> > > +
> > > +  reg:
> > > +    const: 2
> > > +
> > > +  reset-gpios:
> > > +    maxItems: 1
> > > +    description:
> > > +      An active-low reset line for the Bluetooth core; on typical M.2
> > > +      key E modules this is the W_DISABLE2# pin.
> > > +
> >
> > Thanks for adding the new setup for the MT7921S devices. They look good to me.
> > Sometimes, the MT7921S might be set up to wake up the host when it's
> > asleep using a sideband signal.
> > This might need an extra pin called "wakeup" to make it happen. Can
> > you help add this pin to the settings in the same update, or should I
> > do it later?
>
> I suggest you send a patch on top of this one? I'm not sure if you
> would model it as a GPIO or interrupt. And there doesn't seem to be
> any code in the driver expecting it.
>
>
> ChenYu
>
> > > +required:
> > > +  - compatible
> > > +  - reg
> > > +
> > > +unevaluatedProperties: false
> > > +
> > > +examples:
> > > +  - |
> > > +    #include <dt-bindings/gpio/gpio.h>
> > > +
> > > +    mmc {
> > > +        #address-cells = <1>;
> > > +        #size-cells = <0>;
> > > +
> > > +        bluetooth@2 {
> > > +            compatible = "mediatek,mt7921s-bluetooth";
> > > +            reg = <2>;
> > > +            reset-gpios = <&pio 8 GPIO_ACTIVE_LOW>;
> > > +        };
> > > +    };
> > > diff --git a/MAINTAINERS b/MAINTAINERS
> > > index 88981d9f3958..218bc2a21207 100644
> > > --- a/MAINTAINERS
> > > +++ b/MAINTAINERS
> > > @@ -13818,6 +13818,7 @@ M:      Sean Wang <sean.wang@mediatek.com>
> > >  L:     linux-bluetooth@vger.kernel.org
> > >  L:     linux-mediatek@lists.infradead.org (moderated for non-subscribers)
> > >  S:     Maintained
> > > +F:     Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
> > >  F:     Documentation/devicetree/bindings/net/mediatek-bluetooth.txt
> > >  F:     drivers/bluetooth/btmtkuart.c
> > >
> > > --
> > > 2.44.0.683.g7961c838ac-goog
> > >
> > >
Chen-Yu Tsai May 2, 2024, 7:51 a.m. UTC | #6 
On Tue, Apr 16, 2024 at 7:05 AM Rob Herring <robh@kernel.org> wrote:
> On Fri, 12 Apr 2024 15:30:42 +0800, Chen-Yu Tsai wrote:
> > The MediaTek MT7921S is a WiFi/Bluetooth combo chip that works over
> > SDIO. WiFi and Bluetooth are separate SDIO functions within the chip.
> > While the Bluetooth SDIO function is fully discoverable, the chip has
> > a pin that can reset just the Bluetooth core, as opposed to the full
> > chip. This should be described in the device tree.
> >
> > Add a device tree binding for the Bluetooth SDIO function of the MT7921S
> > specifically to document the reset line. This binding is based on the MMC
> > controller binding, which specifies one device node per SDIO function.
> >
> > Cc: Sean Wang <sean.wang@mediatek.com>
> > Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
> > ---
> > Changes since v2:
> > - Expand description and commit message to clearly state that WiFi and
> >   Bluetooth are separate SDIO functions, and that each function should
> >   be a separate device node, as specified by the MMC binding.
> > - Change 'additionalProperties' to 'unevaluatedProperties'
> > - Add missing separating new line
> > - s/ot/to/
> >
> > Angelo's reviewed-by was not picked up due to the above changes.
> >
> > Changes since v1:
> > - Reworded descriptions
> > - Moved binding maintainer section before description
> > - Added missing reference to bluetooth-controller.yaml
> > - Added missing GPIO header to example
> > ---
> >  .../bluetooth/mediatek,mt7921s-bluetooth.yaml | 55 +++++++++++++++++++
> >  MAINTAINERS                                   |  1 +
> >  2 files changed, 56 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
> >
>
> Reviewed-by: Rob Herring <robh@kernel.org>

Luiz, could you pick up this patch?

The other one is already merged in the MediaTek tree.


Thanks!
ChenYu
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml b/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
new file mode 100644
index 000000000000..67ff7caad599
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
@@ -0,0 +1,55 @@ 
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/bluetooth/mediatek,mt7921s-bluetooth.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek MT7921S Bluetooth
+
+maintainers:
+  - Sean Wang <sean.wang@mediatek.com>
+
+description:
+  MT7921S is an SDIO-attached dual-radio WiFi+Bluetooth Combo chip; each
+  function is its own SDIO function on a shared SDIO interface. The chip
+  has two dedicated reset lines, one for each function core.
+  This binding only covers the Bluetooth SDIO function, with one device
+  node describing only this SDIO function.
+
+allOf:
+  - $ref: bluetooth-controller.yaml#
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt7921s-bluetooth
+
+  reg:
+    const: 2
+
+  reset-gpios:
+    maxItems: 1
+    description:
+      An active-low reset line for the Bluetooth core; on typical M.2
+      key E modules this is the W_DISABLE2# pin.
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    mmc {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        bluetooth@2 {
+            compatible = "mediatek,mt7921s-bluetooth";
+            reg = <2>;
+            reset-gpios = <&pio 8 GPIO_ACTIVE_LOW>;
+        };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index 88981d9f3958..218bc2a21207 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -13818,6 +13818,7 @@  M:	Sean Wang <sean.wang@mediatek.com>
 L:	linux-bluetooth@vger.kernel.org
 L:	linux-mediatek@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
+F:	Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
 F:	Documentation/devicetree/bindings/net/mediatek-bluetooth.txt
 F:	drivers/bluetooth/btmtkuart.c