diff mbox series

[net-next,v9,10/13] net: phy: mediatek: Extend 1G TX/RX link pulse time

Message ID 20240626104329.11426-11-SkyLake.Huang@mediatek.com (mailing list archive)
State New
Headers show
Series net: phy: mediatek: Introduce mtk-phy-lib and add 2.5Gphy support | expand

Commit Message

SkyLake Huang (黃啟澤) June 26, 2024, 10:43 a.m. UTC
From: "SkyLake.Huang" <skylake.huang@mediatek.com>

We observe that some 10G devices' (mostly Marvell's chips inside) 1G
training time violates specification, which may last 2230ms and affect
later TX/RX link pulse time. This will invalidate MediaTek series
gigabit Ethernet PHYs' hardware auto downshift mechanism.

Without this patch, if someone is trying to use "4-wire" cable to
connect above devices, MediaTek' gigabit Ethernet PHYs may fail
to downshift to 100Mbps. (If partner 10G devices' downshift mechanism
stops at 1G)

This patch extends our 1G TX/RX link pulse time so that we can still
link up with those 10G devices.

Tested device:
- Netgear GS110EMX's 10G port (Marvell 88X3340P)
- QNAP QSW-M408-4C

Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
---
 drivers/net/phy/mediatek/mtk-ge-soc.c  |  2 +
 drivers/net/phy/mediatek/mtk-ge.c      |  5 +-
 drivers/net/phy/mediatek/mtk-phy-lib.c | 92 ++++++++++++++++++++++++++
 drivers/net/phy/mediatek/mtk.h         | 21 ++++++
 4 files changed, 116 insertions(+), 4 deletions(-)
diff mbox series

Patch

diff --git a/drivers/net/phy/mediatek/mtk-ge-soc.c b/drivers/net/phy/mediatek/mtk-ge-soc.c
index 71d29de..5b2c7a0 100644
--- a/drivers/net/phy/mediatek/mtk-ge-soc.c
+++ b/drivers/net/phy/mediatek/mtk-ge-soc.c
@@ -1396,6 +1396,7 @@  static struct phy_driver mtk_socphy_driver[] = {
 		PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981),
 		.name		= "MediaTek MT7981 PHY",
 		.config_init	= mt798x_phy_config_init,
+		.read_status	= mtk_gphy_cl22_read_status,
 		.config_intr	= genphy_no_config_intr,
 		.handle_interrupt = genphy_handle_interrupt_no_ack,
 		.probe		= mt7981_phy_probe,
@@ -1413,6 +1414,7 @@  static struct phy_driver mtk_socphy_driver[] = {
 		PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7988),
 		.name		= "MediaTek MT7988 PHY",
 		.config_init	= mt798x_phy_config_init,
+		.read_status	= mtk_gphy_cl22_read_status,
 		.config_intr	= genphy_no_config_intr,
 		.handle_interrupt = genphy_handle_interrupt_no_ack,
 		.probe		= mt7988_phy_probe,
diff --git a/drivers/net/phy/mediatek/mtk-ge.c b/drivers/net/phy/mediatek/mtk-ge.c
index 8532f75..3bd8664 100644
--- a/drivers/net/phy/mediatek/mtk-ge.c
+++ b/drivers/net/phy/mediatek/mtk-ge.c
@@ -8,10 +8,6 @@ 
 #define MTK_GPHY_ID_MT7530		0x03a29412
 #define MTK_GPHY_ID_MT7531		0x03a29441
 
-#define MTK_PHY_PAGE_EXTENDED_1			0x0001
-#define MTK_PHY_AUX_CTRL_AND_STATUS		0x14
-#define   MTK_PHY_ENABLE_DOWNSHIFT		BIT(4)
-
 #define MTK_PHY_PAGE_EXTENDED_2			0x0002
 #define MTK_PHY_PAGE_EXTENDED_3			0x0003
 #define MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG11	0x11
@@ -214,6 +210,7 @@  static struct phy_driver mtk_gephy_driver[] = {
 		.name		= "MediaTek MT7531 PHY",
 		.probe		= mt7531_phy_probe,
 		.config_init	= mt7531_phy_config_init,
+		.read_status	= mtk_gphy_cl22_read_status,
 		/* Interrupts are handled by the switch, not the PHY
 		 * itself.
 		 */
diff --git a/drivers/net/phy/mediatek/mtk-phy-lib.c b/drivers/net/phy/mediatek/mtk-phy-lib.c
index 32520af..6bd12fd 100644
--- a/drivers/net/phy/mediatek/mtk-phy-lib.c
+++ b/drivers/net/phy/mediatek/mtk-phy-lib.c
@@ -109,6 +109,98 @@  int mtk_phy_write_page(struct phy_device *phydev, int page)
 }
 EXPORT_SYMBOL_GPL(mtk_phy_write_page);
 
+/* This function deals with the case that 1G AN starts but isn't completed. We
+ * set AN_NEW_LP_CNT_LIMIT with different values time after time to let our
+ * 1G->100Mbps hardware automatic downshift to fit more partner devices.
+ */
+static int extend_an_new_lp_cnt_limit(struct phy_device *phydev)
+{
+	int mmd_read_ret;
+	u32 reg_val;
+	int timeout;
+
+	/* According to table 28-9 & Figure 28-18 in IEEE 802.3,
+	 * link_fail_inhibit_timer of 10/100/1000 Mbps devices ranges from 750
+	 * to "1000ms". Once MTK_PHY_FINAL_SPEED_1000 is set, it means that we
+	 * enter "FLP LINK GOOD CHECK" state, link_fail_inhibit_timer starts and
+	 * this PHY's 1G training starts. If 1G training never starts, we do
+	 * nothing but leave.
+	 */
+	timeout = read_poll_timeout(mmd_read_ret = phy_read_mmd, reg_val,
+				    (mmd_read_ret < 0) ||
+				    reg_val & MTK_PHY_FINAL_SPEED_1000,
+				    10000, 1000000, false, phydev,
+				    MDIO_MMD_VEND1, MTK_PHY_LINK_STATUS_MISC);
+	if (mmd_read_ret < 0)
+		return mmd_read_ret;
+
+	if (!timeout) {
+		/* Once we found MTK_PHY_FINAL_SPEED_1000 is set, no matter 1G
+		 * AN is completed or not, we'll set AN_NEW_LP_CNT_LIMIT again
+		 * and again.
+		 */
+		mtk_tr_modify(phydev, 0x0, 0xf, 0x3c, AN_NEW_LP_CNT_LIMIT_MASK,
+			      FIELD_PREP(AN_NEW_LP_CNT_LIMIT_MASK, 0xf));
+		mdelay(1500);
+
+		timeout = read_poll_timeout(mtk_tr_read, reg_val,
+					    (reg_val & AN_STATE_MASK) !=
+					    (AN_STATE_TX_DISABLE <<
+					     AN_STATE_SHIFT),
+					    10000, 1000000, false, phydev,
+					    0x0, 0xf, 0x2);
+		if (!timeout) {
+			mdelay(625);
+			mtk_tr_modify(phydev, 0x0, 0xf, 0x3c,
+				      AN_NEW_LP_CNT_LIMIT_MASK,
+				      FIELD_PREP(AN_NEW_LP_CNT_LIMIT_MASK,
+						 0x8));
+			mdelay(500);
+			mtk_tr_modify(phydev, 0x0, 0xf, 0x3c,
+				      AN_NEW_LP_CNT_LIMIT_MASK,
+				      FIELD_PREP(AN_NEW_LP_CNT_LIMIT_MASK,
+						 0xf));
+		} else {
+			return -ETIMEDOUT;
+		}
+	}
+
+	return 0;
+}
+
+int mtk_gphy_cl22_read_status(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = genphy_read_status(phydev);
+	if (ret)
+		return ret;
+
+	if (phydev->autoneg == AUTONEG_ENABLE && !phydev->autoneg_complete) {
+		ret = phy_read_paged(phydev, MTK_PHY_PAGE_EXTENDED_1,
+				     MTK_PHY_AUX_CTRL_AND_STATUS);
+		if (ret < 0)
+			return ret;
+
+		/* Once LP_DETECTED is set, it means that"ability_match" in
+		 * IEEE 802.3 Figure 28-18 is set. This happens after we plug in
+		 * cable. Also, LP_DETECTED will be cleared after AN complete.
+		 */
+		if (!FIELD_GET(MTK_PHY_LP_DETECTED_MASK, ret))
+			return 0;
+
+		ret = phy_read(phydev, MII_CTRL1000);
+		if (ret & (ADVERTISE_1000FULL | ADVERTISE_1000HALF)) {
+			ret = extend_an_new_lp_cnt_limit(phydev);
+			if (ret < 0)
+				return ret;
+		}
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(mtk_gphy_cl22_read_status);
+
 int mtk_phy_led_hw_is_supported(struct phy_device *phydev, u8 index,
 				unsigned long rules,
 				unsigned long supported_triggers)
diff --git a/drivers/net/phy/mediatek/mtk.h b/drivers/net/phy/mediatek/mtk.h
index 8c0acea..7bcb137 100644
--- a/drivers/net/phy/mediatek/mtk.h
+++ b/drivers/net/phy/mediatek/mtk.h
@@ -10,8 +10,28 @@ 
 
 #define MTK_EXT_PAGE_ACCESS			0x1f
 #define MTK_PHY_PAGE_STANDARD			0x0000
+#define MTK_PHY_PAGE_EXTENDED_1			0x0001
+#define MTK_PHY_AUX_CTRL_AND_STATUS		0x14
+/* suprv_media_select_RefClk */
+#define   MTK_PHY_LP_DETECTED_MASK		GENMASK(7, 6)
+#define   MTK_PHY_ENABLE_DOWNSHIFT		BIT(4)
+
 #define MTK_PHY_PAGE_EXTENDED_52B5		0x52b5
 
+/* Registers on Token Ring debug nodes */
+/* ch_addr = 0x0, node_addr = 0xf, data_addr = 0x2 */
+#define   AN_STATE_MASK			GENMASK(22, 19)
+#define   AN_STATE_SHIFT		19
+#define   AN_STATE_TX_DISABLE		1
+
+/* ch_addr = 0x0, node_addr = 0xf, data_addr = 0x3c */
+#define AN_NEW_LP_CNT_LIMIT_MASK		GENMASK(23, 20)
+#define AUTO_NP_10XEN				BIT(6)
+
+/* Registers on MDIO_MMD_VEND1 */
+#define MTK_PHY_LINK_STATUS_MISC	(0xa2)
+#define   MTK_PHY_FINAL_SPEED_1000	BIT(3)
+
 /* Registers on MDIO_MMD_VEND2 */
 #define MTK_PHY_LED0_ON_CTRL			0x24
 #define MTK_PHY_LED1_ON_CTRL			0x26
@@ -78,6 +98,7 @@  void __mtk_tr_clr_bits(struct phy_device *phydev, u8 ch_addr, u8 node_addr,
 int mtk_phy_read_page(struct phy_device *phydev);
 int mtk_phy_write_page(struct phy_device *phydev, int page);
 
+int mtk_gphy_cl22_read_status(struct phy_device *phydev);
 int mtk_phy_led_hw_is_supported(struct phy_device *phydev, u8 index,
 				unsigned long rules,
 				unsigned long supported_triggers);