@@ -75,15 +75,12 @@
#define PCIE_MEM_WIN0_HI(win) \
PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI + ((win) * 8)
+#define PCIE_BRCM_MAX_RC_BARS 16
#define PCIE_MISC_RC_BAR1_CONFIG_LO 0x402c
#define PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK 0x1f
-#define PCIE_MISC_RC_BAR2_CONFIG_LO 0x4034
-#define PCIE_MISC_RC_BAR2_CONFIG_LO_SIZE_MASK 0x1f
-#define PCIE_MISC_RC_BAR2_CONFIG_HI 0x4038
+#define PCIE_MISC_RC_BAR4_CONFIG_LO 0x40d4
-#define PCIE_MISC_RC_BAR3_CONFIG_LO 0x403c
-#define PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_MASK 0x1f
#define PCIE_MISC_MSI_BAR_CONFIG_LO 0x4044
#define PCIE_MISC_MSI_BAR_CONFIG_HI 0x4048
@@ -130,6 +127,10 @@
(PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK | \
PCIE_MISC_HARD_PCIE_HARD_DEBUG_L1SS_ENABLE_MASK)
+#define PCIE_MISC_UBUS_BAR1_CONFIG_REMAP 0x40ac
+#define PCIE_MISC_UBUS_BAR1_CONFIG_REMAP_ACCESS_EN_MASK 0x1
+#define PCIE_MISC_UBUS_BAR4_CONFIG_REMAP 0x410c
+
#define PCIE_MSI_INTR2_BASE 0x4500
/* Offsets from INTR2_CPU and MSI_INTR2 BASE offsets */
@@ -222,6 +223,13 @@ enum pcie_type {
BCM4908,
BCM7278,
BCM2711,
+ BCM7712,
+};
+
+struct rc_bar {
+ u64 size;
+ u64 pci_offset;
+ u64 cpu_addr;
};
struct pcie_cfg_data {
@@ -279,6 +287,7 @@ struct brcm_pcie {
struct subdev_regulators *sr;
bool ep_wakeup_capable;
bool has_phy;
+ int num_inbound;
};
static inline bool is_bmips(const struct brcm_pcie *pcie)
@@ -794,23 +803,60 @@ static void brcm_pcie_perst_set_generic(struct brcm_pcie *pcie, u32 val)
writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
}
-static int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
- u64 *rc_bar2_size,
- u64 *rc_bar2_offset)
+static inline void set_bar(struct rc_bar *b, int *count, u64 size,
+ u64 cpu_addr, u64 pci_offset)
+{
+ b->size = size;
+ b->cpu_addr = cpu_addr;
+ b->pci_offset = pci_offset;
+ (*count)++;
+}
+
+static int brcm_pcie_get_rc_bar_sizes_and_offsets(struct brcm_pcie *pcie,
+ struct rc_bar rc_bars[])
{
struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
+ u64 pci_offset, cpu_addr, size = 0, tot_size = 0;
struct resource_entry *entry;
struct device *dev = pcie->dev;
u64 lowest_pcie_addr = ~(u64)0;
- int ret, i = 0;
- u64 size = 0;
+
+ int ret, i = 0, n = 0;
+
+ /*
+ * The HW registers (and PCIe) use order-1 numbering for BARs. As
+ * such, we have rc_bars[0] unused and BAR1 starts at rc_bars[1].
+ */
+ struct rc_bar *b_begin = &rc_bars[1];
+ struct rc_bar *b = b_begin;
+
+ /*
+ * STB chips beside 7712 disable BAR1 by default. It is mapped not
+ * to system memory but to a regiion all of the SOC registers. No
+ * one uses this anymore.
+ */
+ if (pcie->type != BCM7712)
+ set_bar(b++, &n, 0, 0, 0);
resource_list_for_each_entry(entry, &bridge->dma_ranges) {
u64 pcie_beg = entry->res->start - entry->offset;
+ u64 cpu_beg = entry->res->start;
- size += entry->res->end - entry->res->start + 1;
+ size = entry->res->end - entry->res->start + 1;
+ tot_size += size;
if (pcie_beg < lowest_pcie_addr)
lowest_pcie_addr = pcie_beg;
+ /*
+ * 7712 and newer chips may have many BARs, with each
+ * offering a non-overlapping viewport to system memory.
+ * That being said, each BARs size must still be a power of
+ * two.
+ */
+ if (pcie->type == BCM7712)
+ set_bar(b++, &n, size, cpu_beg, pcie_beg);
+
+ if (n > pcie->num_inbound)
+ break;
}
if (lowest_pcie_addr == ~(u64)0) {
@@ -818,13 +864,20 @@ static int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
return -EINVAL;
}
+ /*
+ * 7712 and newer chips do not have an internal memory mapping system
+ * that enables multiple memory controllers. As such, it can return
+ * now w/o doing special configuration.
+ */
+ if (pcie->type == BCM7712)
+ return n;
+
ret = of_property_read_variable_u64_array(pcie->np, "brcm,scb-sizes", pcie->memc_size, 1,
PCIE_BRCM_MAX_MEMC);
-
if (ret <= 0) {
/* Make an educated guess */
pcie->num_memc = 1;
- pcie->memc_size[0] = 1ULL << fls64(size - 1);
+ pcie->memc_size[0] = 1ULL << fls64(tot_size - 1);
} else {
pcie->num_memc = ret;
}
@@ -833,10 +886,15 @@ static int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
for (i = 0, size = 0; i < pcie->num_memc; i++)
size += pcie->memc_size[i];
- /* System memory starts at this address in PCIe-space */
- *rc_bar2_offset = lowest_pcie_addr;
- /* The sum of all memc views must also be a power of 2 */
- *rc_bar2_size = 1ULL << fls64(size - 1);
+ /* Our HW mandates that the window size must be a power of 2 */
+ size = 1ULL << fls64(size - 1);
+
+ /*
+ * For STB chips, the BAR2 cpu_addr is hardwired to the start
+ * of system memory, so we set it to 0.
+ */
+ cpu_addr = 0;
+ pci_offset = lowest_pcie_addr;
/*
* We validate the inbound memory view even though we should trust
@@ -871,25 +929,50 @@ static int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
* outbound memory @ 3GB). So instead it will start at the 1x
* multiple of its size
*/
- if (!*rc_bar2_size || (*rc_bar2_offset & (*rc_bar2_size - 1)) ||
- (*rc_bar2_offset < SZ_4G && *rc_bar2_offset > SZ_2G)) {
+ if (!size || (pci_offset & (size - 1)) ||
+ (pci_offset < SZ_4G && pci_offset > SZ_2G)) {
dev_err(dev, "Invalid rc_bar2_offset/size: size 0x%llx, off 0x%llx\n",
- *rc_bar2_size, *rc_bar2_offset);
+ size, pci_offset);
return -EINVAL;
}
- return 0;
+ /* Enable BAR2, the inbound window for STB chips */
+ set_bar(b++, &n, size, cpu_addr, pci_offset);
+
+ /*
+ * Disable BAR3. On some chips presents the same window as BAR2
+ * but the data appears in a settable endianness.
+ */
+ set_bar(b++, &n, 0, 0, 0);
+
+ return n;
+}
+
+static unsigned int brcm_calc_bar_reg_offset(int bar)
+{
+ if (bar <= 3)
+ return PCIE_MISC_RC_BAR1_CONFIG_LO + 8 * (bar - 1);
+ else
+ return PCIE_MISC_RC_BAR4_CONFIG_LO + 8 * (bar - 4);
+}
+
+static unsigned int brcm_calc_ubus_reg_offset(int bar)
+{
+ if (bar <= 3)
+ return PCIE_MISC_UBUS_BAR1_CONFIG_REMAP + 8 * (bar - 1);
+ else
+ return PCIE_MISC_UBUS_BAR4_CONFIG_REMAP + 8 * (bar - 4);
}
static int brcm_pcie_setup(struct brcm_pcie *pcie)
{
- u64 rc_bar2_offset, rc_bar2_size;
+ struct rc_bar rc_bars[PCIE_BRCM_MAX_RC_BARS];
void __iomem *base = pcie->base;
struct pci_host_bridge *bridge;
struct resource_entry *entry;
u32 tmp, burst, aspm_support;
- int num_out_wins = 0;
- int ret, memc;
+ int num_out_wins = 0, num_rc_bars = 0;
+ int i, memc;
/* Reset the bridge */
pcie->bridge_sw_init_set(pcie, 1);
@@ -938,17 +1021,47 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_PCIE_RCB_64B_MODE_MASK);
writel(tmp, base + PCIE_MISC_MISC_CTRL);
- ret = brcm_pcie_get_rc_bar2_size_and_offset(pcie, &rc_bar2_size,
- &rc_bar2_offset);
- if (ret)
- return ret;
+ num_rc_bars = brcm_pcie_get_rc_bar_sizes_and_offsets(pcie, rc_bars);
+ if (num_rc_bars < 0)
+ return num_rc_bars;
+
+ for (i = 1; i <= num_rc_bars; i++) {
+ u64 pci_offset = rc_bars[i].pci_offset;
+ u64 cpu_addr = rc_bars[i].cpu_addr;
+ u64 size = rc_bars[i].size;
+ u32 reg_offset = brcm_calc_bar_reg_offset(i);
+
+ tmp = lower_32_bits(pci_offset);
+ u32p_replace_bits(&tmp, brcm_pcie_encode_ibar_size(size),
+ PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK);
+
+ /* Write low */
+ writel(tmp, base + reg_offset);
+ /* Write high */
+ writel(upper_32_bits(pci_offset),
+ base + reg_offset + 4);
+
+ /*
+ * Most STB chips:
+ * Do nothing.
+ * 7712:
+ * All of their BARs need to be set.
+ */
+ if (pcie->type == BCM7712) {
+ /* BUS remap register settings */
+ reg_offset = brcm_calc_ubus_reg_offset(i);
+ tmp = lower_32_bits(cpu_addr) & ~0xfff;
+ tmp |= PCIE_MISC_UBUS_BAR1_CONFIG_REMAP_ACCESS_EN_MASK;
+ writel(tmp, base + reg_offset);
+ tmp = upper_32_bits(cpu_addr);
+ writel(tmp, base + reg_offset + 4);
+ }
+ }
- tmp = lower_32_bits(rc_bar2_offset);
- u32p_replace_bits(&tmp, brcm_pcie_encode_ibar_size(rc_bar2_size),
- PCIE_MISC_RC_BAR2_CONFIG_LO_SIZE_MASK);
- writel(tmp, base + PCIE_MISC_RC_BAR2_CONFIG_LO);
- writel(upper_32_bits(rc_bar2_offset),
- base + PCIE_MISC_RC_BAR2_CONFIG_HI);
+ if (!brcm_pcie_rc_mode(pcie)) {
+ dev_err(pcie->dev, "PCIe RC controller misconfigured as Endpoint\n");
+ return -EINVAL;
+ }
tmp = readl(base + PCIE_MISC_MISC_CTRL);
for (memc = 0; memc < pcie->num_memc; memc++) {
@@ -970,25 +1083,12 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
* 4GB or when the inbound area is smaller than 4GB (taking into
* account the rounding-up we're forced to perform).
*/
- if (rc_bar2_offset >= SZ_4G || (rc_bar2_size + rc_bar2_offset) < SZ_4G)
+ if (rc_bars[2].pci_offset >= SZ_4G ||
+ (rc_bars[2].size + rc_bars[2].pci_offset) < SZ_4G)
pcie->msi_target_addr = BRCM_MSI_TARGET_ADDR_LT_4GB;
else
pcie->msi_target_addr = BRCM_MSI_TARGET_ADDR_GT_4GB;
- if (!brcm_pcie_rc_mode(pcie)) {
- dev_err(pcie->dev, "PCIe RC controller misconfigured as Endpoint\n");
- return -EINVAL;
- }
-
- /* disable the PCIe->GISB memory window (RC_BAR1) */
- tmp = readl(base + PCIE_MISC_RC_BAR1_CONFIG_LO);
- tmp &= ~PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK;
- writel(tmp, base + PCIE_MISC_RC_BAR1_CONFIG_LO);
-
- /* disable the PCIe->SCB memory window (RC_BAR3) */
- tmp = readl(base + PCIE_MISC_RC_BAR3_CONFIG_LO);
- tmp &= ~PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_MASK;
- writel(tmp, base + PCIE_MISC_RC_BAR3_CONFIG_LO);
/* Don't advertise L0s capability if 'aspm-no-l0s' */
aspm_support = PCIE_LINK_STATE_L1;
@@ -1628,6 +1728,7 @@ static int brcm_pcie_probe(struct platform_device *pdev)
pcie->perst_set = data->perst_set;
pcie->bridge_sw_init_set = data->bridge_sw_init_set;
pcie->has_phy = data->has_phy;
+ pcie->num_inbound = (pcie->type == BCM7712) ? 10 : 3;
pcie->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(pcie->base))
Previously, our chips provided three inbound "BARS" with fixed purposes: the first was for mapping SOC registers, the second was for memory, and the third was for memory but with the endian swapped. We typically only used one of these BARs. Complicating that BARs usage was the fact that the PCIe HW would do a baroque internal mapping of system memory, and concatenate the regions of multiple memory controllers. Newer chips such as the 7712 and Cable Modem SOCs have taken a step forward and now provide multiple inbound BARs. This works in concert with the dma-ranges property, where each provided range becomes an inbound BAR. This commit provides support for these new chips and their multiple inbound BARs but also keeps the legacy support for the older system. Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com> --- drivers/pci/controller/pcie-brcmstb.c | 199 +++++++++++++++++++------- 1 file changed, 150 insertions(+), 49 deletions(-)