diff mbox series

[v4,6/7] arm64: dts: rockchip: hook up the MCU on the QNAP TS433

Message ID 20240810184743.277248-7-heiko@sntech.de (mailing list archive)
State New, archived
Headers show
Series Drivers to support the MCU on QNAP NAS devices | expand

Commit Message

Heiko Stuebner Aug. 10, 2024, 6:47 p.m. UTC
The MCU is an important part of the device functionality. It provides
functionality like fan-control, more leds, etc and even more important
without it, the NAS-device cannot even fully turned off.

Hook up the serial device to its uart and hook into the thermal
management to control the fan according to the cpu temperature.

While the MCU also provides a temperature sensor for the case, this one
is just polled and does not provide functionality for handling trip
points in hardware, so a lot of polling would be involved.
As the cpu is only cooled passively in these devices, it's temperature
rising will indicate the temperature level of the system just earlier.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
 .../boot/dts/rockchip/rk3568-qnap-ts433.dts   | 57 +++++++++++++++++++
 1 file changed, 57 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
index 90d8d5266299b..6405ec7d47361 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
@@ -463,6 +463,54 @@  rgmii_phy0: ethernet-phy@0 {
 	};
 };
 
+/*
+ * The MCU can provide system temperature too, but only by polling and of
+ * course also cannot set trip points. So attach to the cpu thermal-zone
+ * instead to control the fan.
+ */
+&cpu_thermal {
+	trips {
+		case_fan0: case-fan0 {
+			hysteresis = <2000>;
+			temperature = <35000>;
+			type = "active";
+		};
+
+		case_fan1: case-fan1 {
+			hysteresis = <2000>;
+			temperature = <45000>;
+			type = "active";
+		};
+
+		case_fan2: case-fan2 {
+			hysteresis = <2000>;
+			temperature = <65000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		/*
+		 * Always provide some air movement, due to small case
+		 * full of harddrives.
+		 */
+		map1 {
+			cooling-device = <&fan THERMAL_NO_LIMIT 1>;
+			trip = <&case_fan0>;
+		};
+
+		map2 {
+			cooling-device = <&fan 2 3>;
+			trip = <&case_fan1>;
+		};
+
+		map3 {
+			cooling-device = <&fan 4 THERMAL_NO_LIMIT>;
+			trip = <&case_fan2>;
+		};
+	};
+};
+
 &pcie30phy {
 	data-lanes = <1 2>;
 	status = "okay";
@@ -562,6 +610,15 @@  &tsadc {
  */
 &uart0 {
 	status = "okay";
+
+	mcu {
+		compatible = "qnap,ts433-mcu";
+
+		fan: fan-0 {
+			#cooling-cells = <2>;
+			cooling-levels = <0 64 89 128 166 204 221 238>;
+		};
+	};
 };
 
 /*