diff mbox series

[v9,2/4] arm64: dts: exynos: add initial CMU clock nodes in ExynosAuto v920

Message ID 20240821232652.1077701-3-sunyeal.hong@samsung.com (mailing list archive)
State New, archived
Headers show
Series initial clock support for exynosauto v920 SoC | expand

Commit Message

Sunyeal Hong Aug. 21, 2024, 11:26 p.m. UTC 
Add cmu_top, cmu_peric0 clock nodes and
switch USI clocks instead of dummy fixed-rate-clock.

Signed-off-by: Sunyeal Hong <sunyeal.hong@samsung.com>
---
 .../arm64/boot/dts/exynos/exynosautov920.dtsi | 40 +++++++++++++------
 1 file changed, 27 insertions(+), 13 deletions(-)

Comments

Krzysztof Kozlowski Aug. 23, 2024, 7:15 a.m. UTC | #1 
On Thu, Aug 22, 2024 at 08:26:50AM +0900, Sunyeal Hong wrote:
> Add cmu_top, cmu_peric0 clock nodes and
> switch USI clocks instead of dummy fixed-rate-clock.
> 
> Signed-off-by: Sunyeal Hong <sunyeal.hong@samsung.com>
> ---
>  .../arm64/boot/dts/exynos/exynosautov920.dtsi | 40 +++++++++++++------
>  1 file changed, 27 insertions(+), 13 deletions(-)

In the future, please remember about correct order of patches. Nothing
can depend on the DTS, thus DTS is always the last. No need to resend
for that.

Best regards,
Krzysztof
Krzysztof Kozlowski Aug. 23, 2024, 7:42 a.m. UTC | #2 
On Thu, 22 Aug 2024 08:26:50 +0900, Sunyeal Hong wrote:
> Add cmu_top, cmu_peric0 clock nodes and
> switch USI clocks instead of dummy fixed-rate-clock.
> 
> 

Applied, thanks!

[2/4] arm64: dts: exynos: add initial CMU clock nodes in ExynosAuto v920
      https://git.kernel.org/krzk/linux/c/4d06000979cda26e914552d486e5364248025fcd

Best regards,
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/exynos/exynosautov920.dtsi b/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
index c1c8566d74f5..91882b37fdb3 100644
--- a/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
@@ -6,6 +6,7 @@ 
  *
  */
 
+#include <dt-bindings/clock/samsung,exynosautov920.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/soc/samsung,exynos-usi.h>
 
@@ -38,17 +39,6 @@  xtcxo: clock {
 		clock-output-names = "oscclk";
 	};
 
-	/*
-	 * FIXME: Keep the stub clock for serial driver, until proper clock
-	 * driver is implemented.
-	 */
-	clock_usi: clock-usi {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <200000000>;
-		clock-output-names = "usi";
-	};
-
 	cpus: cpus {
 		#address-cells = <2>;
 		#size-cells = <0>;
@@ -192,6 +182,19 @@  gic: interrupt-controller@10400000 {
 			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		cmu_peric0: clock-controller@10800000 {
+			compatible = "samsung,exynosautov920-cmu-peric0";
+			reg = <0x10800000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&xtcxo>,
+				 <&cmu_top DOUT_CLKCMU_PERIC0_NOC>,
+				 <&cmu_top DOUT_CLKCMU_PERIC0_IP>;
+			clock-names = "oscclk",
+				      "noc",
+				      "ip";
+		};
+
 		syscon_peric0: syscon@10820000 {
 			compatible = "samsung,exynosautov920-peric0-sysreg",
 				     "syscon";
@@ -213,7 +216,8 @@  usi_0: usi@108800c0 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
-			clocks = <&clock_usi>, <&clock_usi>;
+			clocks = <&cmu_peric0 CLK_MOUT_PERIC0_NOC_USER>,
+				 <&cmu_peric0 CLK_DOUT_PERIC0_USI00_USI>;
 			clock-names = "pclk", "ipclk";
 			status = "disabled";
 
@@ -224,7 +228,8 @@  serial_0: serial@10880000 {
 				interrupts = <GIC_SPI 764 IRQ_TYPE_LEVEL_HIGH>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&uart0_bus>;
-				clocks = <&clock_usi>, <&clock_usi>;
+				clocks = <&cmu_peric0 CLK_MOUT_PERIC0_NOC_USER>,
+					 <&cmu_peric0 CLK_DOUT_PERIC0_USI00_USI>;
 				clock-names = "uart", "clk_uart_baud0";
 				samsung,uart-fifosize = <256>;
 				status = "disabled";
@@ -254,6 +259,15 @@  pinctrl_peric1: pinctrl@10c30000 {
 			interrupts = <GIC_SPI 781 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		cmu_top: clock-controller@11000000 {
+			compatible = "samsung,exynosautov920-cmu-top";
+			reg = <0x11000000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&xtcxo>;
+			clock-names = "oscclk";
+		};
+
 		pinctrl_alive: pinctrl@11850000 {
 			compatible = "samsung,exynosautov920-pinctrl";
 			reg = <0x11850000 0x10000>;