new file mode 100644
@@ -0,0 +1,119 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/st,stm32mp25-combophy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STM32MP25 USB3/PCIe COMBOPHY
+
+maintainers:
+ - Christian Bruel <christian.bruel@foss.st.com>
+
+description:
+ Single lane PHY shared (exclusive) between the USB3 and PCIe controllers.
+ Supports 5Gbit/s for USB3 and PCIe gen2 or 2.5Gbit/s for PCIe gen1.
+
+properties:
+ compatible:
+ const: st,stm32mp25-combophy
+
+ reg:
+ maxItems: 1
+
+ "#phy-cells":
+ const: 1
+
+ clocks:
+ minItems: 2
+ items:
+ - description: apb Bus clock mandatory to access registers.
+ - description: ker Internal RCC reference clock for USB3 or PCIe
+ - description: pad Optional on board clock input for PCIe only. Typically an
+ external 100Mhz oscillator wired on dedicated CLKIN pad. Used as reference
+ clock input instead of the ker
+
+ clock-names:
+ minItems: 2
+ items:
+ - const: apb
+ - const: ker
+ - const: pad
+
+ resets:
+ maxItems: 1
+
+ reset-names:
+ const: phy
+
+ power-domains:
+ maxItems: 1
+
+ wakeup-source: true
+
+ interrupts:
+ maxItems: 1
+ description: interrupt used for wakeup
+
+ access-controllers:
+ maxItems: 1
+ description: Phandle to the rifsc device to check access right.
+
+ st,ssc-on:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ A property whose presence indicates that the Spread Spectrum Clocking is active.
+
+ st,rx-equalizer:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 7
+ default: 2
+ description:
+ A 3 bit value to tune the RX fixed equalizer setting for optimal eye compliance
+
+ st,output-micro-ohms:
+ minimum: 3999000
+ maximum: 6090000
+ default: 4968000
+ description:
+ A value property to tune the Single Ended Output Impedance, simulations results
+ at 25C for a VDDP=0.8V. The hardware accepts discrete values in this range.
+
+ st,output-vswing-microvolt:
+ minimum: 442000
+ maximum: 803000
+ default: 803000
+ description:
+ A value property in microvolt to tune the Single Ended Output Voltage Swing to change the
+ Vlo, Vhi for a VDDP = 0.8V. The hardware accepts discrete values in this range.
+
+required:
+ - compatible
+ - reg
+ - "#phy-cells"
+ - clocks
+ - clock-names
+ - resets
+ - reset-names
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/st,stm32mp25-rcc.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/reset/st,stm32mp25-rcc.h>
+
+ phy@480c0000 {
+ compatible = "st,stm32mp25-combophy";
+ reg = <0x480c0000 0x1000>;
+ #phy-cells = <1>;
+ clocks = <&rcc CK_BUS_USB3PCIEPHY>, <&rcc CK_KER_USB3PCIEPHY>;
+ clock-names = "apb", "ker";
+ resets = <&rcc USB3PCIEPHY_R>;
+ reset-names = "phy";
+ access-controllers = <&rifsc 67>;
+ power-domains = <&CLUSTER_PD>;
+ wakeup-source;
+ interrupts-extended = <&exti1 45 IRQ_TYPE_EDGE_FALLING>;
+ };
Document the bindings for STM32 COMBOPHY interface, used to support the PCIe and USB3 stm32mp25 drivers. Following entries can be used to tune caracterisation parameters - st,output-micro-ohms and st,output-vswing-microvolt bindings entries to tune the impedance and voltage swing using discrete simulation results - st,rx-equalizer register to set the internal rx equalizer filter value. Signed-off-by: Christian Bruel <christian.bruel@foss.st.com> --- .../bindings/phy/st,stm32mp25-combophy.yaml | 119 ++++++++++++++++++ 1 file changed, 119 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/st,stm32mp25-combophy.yaml