| Message ID | 20240927103005.17605-7-pablo.sun@mediatek.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Enable Mali GPU on MediaTek Genio 700 EVK | expand |
Il 27/09/24 12:30, Pablo Sun ha scritto: > Configure GPU regulator supplies and enable GPU for GENIO 700 EVK. > > The GPU in MT8390 & MT8188 has two power inputs: "DVDD_GPU" and > "DVDD_SRAM_GPU". In Genio 700 EVK, DVDD_GPU is supplied by > mt6359_vproc2_buck_reg, and DVDD_SRAM_GPU is supplied by > mt6359_vsram_others_ldo_reg. > > According to section 5.2 "Recommended Operating Conditions" in > MT8390 IoT Application Processor Datasheet v1.9, The recommended > operating voltage ranges are: > > - DVDD_GPU: min 0.55V, max 0.86V, typical 0.75V > - DVDD_SRAM_GPU: min 0.71V, max 0.92V, typical 0.85V > > To further optimize power saving, we couple DVDD_SRAM_GPU to > DVDD_GPU according to the following relation: > > - For opp-880000000 or lower frequency, keep 0.75V > - For opp-915000000 and higher, DVDD_SRAM_GPU should follow > DVDD_GPU. The exact voltage for DVDD_GPU should be decided by > speed binning. > > This rule is derived from the OPP table in the link. > > In addition, set the voltage spread to 6250 uV, the step size of > 'ldo_vsram_others' regulator of mt6359, otherwise the regulator > set_voltage operation fails. > > Link: https://gitlab.com/mediatek/aiot/rity/meta-mediatek-bsp/-/blob/eedd6aedd4b0cfc0ee79b9c9b9650dfa73cf87f6/recipes-kernel/dtbo/mt8390/gpu-mali.dts > Signed-off-by: Pablo Sun <pablo.sun@mediatek.com> > Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
diff --git a/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts b/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts index 1474bef7e754..0a6c9871b41e 100644 --- a/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts +++ b/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts @@ -190,6 +190,11 @@ usb_p2_vbus: regulator-10 { }; }; +&gpu { + mali-supply = <&mt6359_vproc2_buck_reg>; + status = "okay"; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>; @@ -253,6 +258,14 @@ &i2c6 { status = "okay"; }; +&mfg0 { + domain-supply = <&mt6359_vproc2_buck_reg>; +}; + +&mfg1 { + domain-supply = <&mt6359_vsram_others_ldo_reg>; +}; + &mmc0 { status = "okay"; pinctrl-names = "default", "state_uhs"; @@ -314,6 +327,15 @@ &mt6359_vpa_buck_reg { regulator-max-microvolt = <3100000>; }; +&mt6359_vproc2_buck_reg { + /* The name "vgpu" is required by mtk-regulator-coupler */ + regulator-name = "vgpu"; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <800000>; + regulator-coupled-with = <&mt6359_vsram_others_ldo_reg>; + regulator-coupled-max-spread = <6250>; +}; + &mt6359_vpu_buck_reg { regulator-always-on; }; @@ -326,6 +348,15 @@ &mt6359_vsim1_ldo_reg { regulator-enable-ramp-delay = <480>; }; +&mt6359_vsram_others_ldo_reg { + /* The name "vsram_gpu" is required by mtk-regulator-coupler */ + regulator-name = "vsram_gpu"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <800000>; + regulator-coupled-with = <&mt6359_vproc2_buck_reg>; + regulator-coupled-max-spread = <6250>; +}; + &mt6359_vufs_ldo_reg { regulator-always-on; };
Configure GPU regulator supplies and enable GPU for GENIO 700 EVK. The GPU in MT8390 & MT8188 has two power inputs: "DVDD_GPU" and "DVDD_SRAM_GPU". In Genio 700 EVK, DVDD_GPU is supplied by mt6359_vproc2_buck_reg, and DVDD_SRAM_GPU is supplied by mt6359_vsram_others_ldo_reg. According to section 5.2 "Recommended Operating Conditions" in MT8390 IoT Application Processor Datasheet v1.9, The recommended operating voltage ranges are: - DVDD_GPU: min 0.55V, max 0.86V, typical 0.75V - DVDD_SRAM_GPU: min 0.71V, max 0.92V, typical 0.85V To further optimize power saving, we couple DVDD_SRAM_GPU to DVDD_GPU according to the following relation: - For opp-880000000 or lower frequency, keep 0.75V - For opp-915000000 and higher, DVDD_SRAM_GPU should follow DVDD_GPU. The exact voltage for DVDD_GPU should be decided by speed binning. This rule is derived from the OPP table in the link. In addition, set the voltage spread to 6250 uV, the step size of 'ldo_vsram_others' regulator of mt6359, otherwise the regulator set_voltage operation fails. Link: https://gitlab.com/mediatek/aiot/rity/meta-mediatek-bsp/-/blob/eedd6aedd4b0cfc0ee79b9c9b9650dfa73cf87f6/recipes-kernel/dtbo/mt8390/gpu-mali.dts Signed-off-by: Pablo Sun <pablo.sun@mediatek.com> Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> --- .../dts/mediatek/mt8390-genio-700-evk.dts | 31 +++++++++++++++++++ 1 file changed, 31 insertions(+)