diff mbox series

[net-next,v6,4/5] net: stmmac: Add PCI driver support for BCM8958x

Message ID 20241018205332.525595-5-jitendra.vegiraju@broadcom.com (mailing list archive)
State New
Headers show
Series net: stmmac: Add PCI driver support for BCM8958x | expand

Commit Message

Jitendra Vegiraju Oct. 18, 2024, 8:53 p.m. UTC
From: Jitendra Vegiraju <jitendra.vegiraju@broadcom.com>

Add PCI ethernet driver support for Broadcom BCM8958x SoC devices used
in automotive applications.

This SoC device has PCIe ethernet MAC attached to an integrated ethernet
switch using XGMII interface. The PCIe ethernet controller is presented to
the Linux host as PCI network device.

The following block diagram gives an overview of the application.
             +=================================+
             |       Host CPU/Linux            |
             +=================================+
                        || PCIe
                        ||
        +==========================================+
        |           +--------------+               |
        |           | PCIE Endpoint|               |
        |           | Ethernet     |               |
        |           | Controller   |               |
        |           |   DMA        |               |
        |           +--------------+               |
        |           |   MAC        |   BCM8958X    |
        |           +--------------+   SoC         |
        |               || XGMII                   |
        |               ||                         |
        |           +--------------+               |
        |           | Ethernet     |               |
        |           | switch       |               |
        |           +--------------+               |
        |             || || || ||                  |
        +==========================================+
                      || || || || More external interfaces

The MAC IP block on BCM8958x is based on Synopsis XGMAC 4.00a core. This
driver uses common dwxgmac2 code where applicable.
Driver functionality specific to this MAC is implemented in dw25gmac.c.

Management of integrated ethernet switch on this SoC is not handled by
the PCIe interface.
Since BCM8958x is an early adopter device, override the hardware reported
synopsis versions with actual DW25MAC versions that support hdma.

This SoC device has PCIe ethernet MAC directly attached to an integrated
ethernet switch using XGMII interface. Since device tree support is not
available on this platform, a software node is created to enable
fixed-link support using phylink driver.

Signed-off-by: Jitendra Vegiraju <jitendra.vegiraju@broadcom.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-brcm.c  | 478 ++++++++++++++++++
 .../net/ethernet/stmicro/stmmac/stmmac_main.c |  26 +
 2 files changed, 504 insertions(+)
 create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-brcm.c
diff mbox series

Patch

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-brcm.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-brcm.c
new file mode 100644
index 000000000000..d245af503fe8
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-brcm.c
@@ -0,0 +1,478 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/* Copyright (c) 2024 Broadcom Corporation
+ *
+ * PCI driver for ethernet interface of BCM8958X automotive switch chip.
+ *
+ * High level block diagram of the device.
+ *              +=================================+
+ *              |       Host CPU/Linux            |
+ *              +=================================+
+ *                         || PCIe
+ *                         ||
+ *         +==========================================+
+ *         |           +--------------+               |
+ *         |           | PCIE Endpoint|               |
+ *         |           | Ethernet     |               |
+ *         |           | Controller   |               |
+ *         |           |   DMA        |               |
+ *         |           +--------------+               |
+ *         |           |   MAC        |   BCM8958X    |
+ *         |           +--------------+   SoC         |
+ *         |               || XGMII                   |
+ *         |               ||                         |
+ *         |           +--------------+               |
+ *         |           | Ethernet     |               |
+ *         |           | switch       |               |
+ *         |           +--------------+               |
+ *         |             || || || ||                  |
+ *         +==========================================+
+ *                       || || || || More external interfaces
+ *
+ * This SoC device has PCIe ethernet MAC directly attached to an integrated
+ * ethernet switch using XGMII interface. Since devicetree support is not
+ * available on this platform, a software node is created to enable
+ * fixed-link support using phylink driver.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/dmi.h>
+#include <linux/pci.h>
+#include <linux/phy.h>
+
+#include "stmmac.h"
+#include "dwxgmac2.h"
+#include "dw25gmac.h"
+
+#define PCI_DEVICE_ID_BROADCOM_BCM8958X		0xa00d
+#define BRCM_MAX_MTU				1500
+
+/* TX and RX Queue counts */
+#define BRCM_TX_Q_COUNT				4
+#define BRCM_RX_Q_COUNT				4
+
+#define BRCM_XGMAC_BAR0_MASK			BIT(0)
+
+#define BRCM_XGMAC_IOMEM_MISC_REG_OFFSET	0x0
+#define BRCM_XGMAC_IOMEM_MBOX_REG_OFFSET	0x1000
+#define BRCM_XGMAC_IOMEM_CFG_REG_OFFSET		0x3000
+
+#define XGMAC_PCIE_CFG_MSIX_ADDR_MATCH_LOW	0x940
+#define XGMAC_PCIE_CFG_MSIX_ADDR_MATCH_LO_VALUE	0x00000001
+#define XGMAC_PCIE_CFG_MSIX_ADDR_MATCH_HIGH	0x944
+#define XGMAC_PCIE_CFG_MSIX_ADDR_MATCH_HI_VALUE	0x88000000
+
+#define XGMAC_PCIE_MISC_MII_CTRL_OFFSET			0x4
+#define XGMAC_PCIE_MISC_MII_CTRL_PAUSE_RX		BIT(0)
+#define XGMAC_PCIE_MISC_MII_CTRL_PAUSE_TX		BIT(1)
+#define XGMAC_PCIE_MISC_MII_CTRL_LINK_UP		BIT(2)
+#define XGMAC_PCIE_MISC_PCIESS_CTRL_OFFSET		0x8
+#define XGMAC_PCIE_MISC_PCIESS_CTRL_EN_MSI_MSIX		BIT(9)
+#define XGMAC_PCIE_MISC_MSIX_ADDR_MATCH_LO_OFFSET	0x90
+#define XGMAC_PCIE_MISC_MSIX_ADDR_MATCH_LO_VALUE	0x00000001
+#define XGMAC_PCIE_MISC_MSIX_ADDR_MATCH_HI_OFFSET	0x94
+#define XGMAC_PCIE_MISC_MSIX_ADDR_MATCH_HI_VALUE	0x88000000
+#define XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_EP2HOST0_OFFSET	0x700
+#define XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_EP2HOST0_VALUE	1
+#define XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_EP2HOST1_OFFSET	0x704
+#define XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_EP2HOST1_VALUE	1
+#define XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_EP2HOST_DBELL_OFFSET	0x728
+#define XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_EP2HOST_DBELL_VALUE	1
+#define XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_SBD_ALL_OFFSET	0x740
+#define XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_SBD_ALL_VALUE	0
+
+/* MSIX Vector map register starting offsets */
+#define XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_RX0_PF0_OFFSET	0x840
+#define XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_TX0_PF0_OFFSET	0x890
+#define BRCM_MAX_DMA_CHANNEL_PAIRS		4
+#define BRCM_XGMAC_MSI_MAC_VECTOR		0
+#define BRCM_XGMAC_MSI_RX_VECTOR_START		1
+#define BRCM_XGMAC_MSI_TX_VECTOR_START		2
+#define BRCM_XGMAC_MSI_VECTOR_MAX	(BRCM_XGMAC_MSI_RX_VECTOR_START + \
+					 BRCM_MAX_DMA_CHANNEL_PAIRS * 2)
+
+static char *fixed_link_node_name = "fixed-link";
+
+static const struct property_entry fixed_link_properties[] = {
+	PROPERTY_ENTRY_U32("speed", 10000),
+	PROPERTY_ENTRY_BOOL("full-duplex"),
+	PROPERTY_ENTRY_BOOL("pause"),
+	{ }
+};
+
+struct brcm_priv_data {
+	void __iomem *mbox_regs;    /* MBOX  Registers*/
+	void __iomem *misc_regs;    /* MISC  Registers*/
+	void __iomem *xgmac_regs;   /* XGMAC Registers*/
+	struct software_node fixed_link_node;
+};
+
+struct dwxgmac_brcm_pci_info {
+	int (*setup)(struct pci_dev *pdev, struct plat_stmmacenet_data *plat);
+};
+
+static void misc_iowrite(struct brcm_priv_data *brcm_priv,
+			 u32 reg, u32 val)
+{
+	iowrite32(val, brcm_priv->misc_regs + reg);
+}
+
+static void dwxgmac_brcm_common_default_data(struct plat_stmmacenet_data *plat)
+{
+	int i;
+
+	plat->has_xgmac = 1;
+	plat->force_sf_dma_mode = 1;
+	plat->mac_port_sel_speed = SPEED_10000;
+	plat->clk_ptp_rate = 125000000;
+	plat->clk_ref_rate = 250000000;
+	plat->tx_coe = 1;
+	plat->rx_coe = 1;
+	plat->max_speed = SPEED_10000;
+
+	/* Set default value for multicast hash bins */
+	plat->multicast_filter_bins = HASH_TABLE_SIZE;
+
+	/* Set default value for unicast filter entries */
+	plat->unicast_filter_entries = 1;
+
+	/* Set the maxmtu to device's default */
+	plat->maxmtu = BRCM_MAX_MTU;
+
+	/* Set default number of RX and TX queues to use */
+	plat->tx_queues_to_use = BRCM_TX_Q_COUNT;
+	plat->rx_queues_to_use = BRCM_RX_Q_COUNT;
+
+	plat->tx_sched_algorithm = MTL_TX_ALGORITHM_SP;
+	for (i = 0; i < plat->tx_queues_to_use; i++) {
+		plat->tx_queues_cfg[i].use_prio = false;
+		plat->tx_queues_cfg[i].prio = 0;
+		plat->tx_queues_cfg[i].mode_to_use = MTL_QUEUE_AVB;
+	}
+
+	plat->rx_sched_algorithm = MTL_RX_ALGORITHM_SP;
+	for (i = 0; i < plat->rx_queues_to_use; i++) {
+		plat->rx_queues_cfg[i].use_prio = false;
+		plat->rx_queues_cfg[i].mode_to_use = MTL_QUEUE_AVB;
+		plat->rx_queues_cfg[i].pkt_route = 0x0;
+		plat->rx_queues_cfg[i].chan = i;
+	}
+}
+
+static int dwxgmac_brcm_default_data(struct pci_dev *pdev,
+				     struct plat_stmmacenet_data *plat)
+{
+	/* Set common default data first */
+	dwxgmac_brcm_common_default_data(plat);
+
+	plat->snps_id = DW25GMAC_CORE_4_00;
+	plat->dev_id = DW25GMAC_ID;
+	plat->bus_id = 0;
+	plat->phy_addr = 0;
+	plat->phy_interface = PHY_INTERFACE_MODE_XGMII;
+
+	plat->dma_cfg->pbl = 32;
+	plat->dma_cfg->pblx8 = 0;
+	plat->dma_cfg->aal = 0;
+	plat->dma_cfg->eame = 1;
+
+	plat->axi->axi_wr_osr_lmt = 31;
+	plat->axi->axi_rd_osr_lmt = 31;
+	plat->axi->axi_fb = 0;
+	plat->axi->axi_blen[0] = 4;
+	plat->axi->axi_blen[1] = 8;
+	plat->axi->axi_blen[2] = 16;
+	plat->axi->axi_blen[3] = 32;
+	plat->axi->axi_blen[4] = 64;
+	plat->axi->axi_blen[5] = 128;
+	plat->axi->axi_blen[6] = 256;
+
+	return 0;
+}
+
+static struct dwxgmac_brcm_pci_info dwxgmac_brcm_pci_info = {
+	.setup = dwxgmac_brcm_default_data,
+};
+
+static void brcm_config_misc_regs(struct pci_dev *pdev,
+				  struct brcm_priv_data *brcm_priv)
+{
+	pci_write_config_dword(pdev, XGMAC_PCIE_CFG_MSIX_ADDR_MATCH_LOW,
+			       XGMAC_PCIE_CFG_MSIX_ADDR_MATCH_LO_VALUE);
+	pci_write_config_dword(pdev, XGMAC_PCIE_CFG_MSIX_ADDR_MATCH_HIGH,
+			       XGMAC_PCIE_CFG_MSIX_ADDR_MATCH_HI_VALUE);
+
+	misc_iowrite(brcm_priv, XGMAC_PCIE_MISC_MSIX_ADDR_MATCH_LO_OFFSET,
+		     XGMAC_PCIE_MISC_MSIX_ADDR_MATCH_LO_VALUE);
+	misc_iowrite(brcm_priv, XGMAC_PCIE_MISC_MSIX_ADDR_MATCH_HI_OFFSET,
+		     XGMAC_PCIE_MISC_MSIX_ADDR_MATCH_HI_VALUE);
+
+	/* Enable Switch Link */
+	misc_iowrite(brcm_priv, XGMAC_PCIE_MISC_MII_CTRL_OFFSET,
+		     XGMAC_PCIE_MISC_MII_CTRL_PAUSE_RX |
+		     XGMAC_PCIE_MISC_MII_CTRL_PAUSE_TX |
+		     XGMAC_PCIE_MISC_MII_CTRL_LINK_UP);
+}
+
+static int brcm_config_multi_msi(struct pci_dev *pdev,
+				 struct plat_stmmacenet_data *plat,
+				 struct stmmac_resources *res)
+{
+	int ret;
+	int i;
+
+	ret = pci_alloc_irq_vectors(pdev, BRCM_XGMAC_MSI_VECTOR_MAX,
+				    BRCM_XGMAC_MSI_VECTOR_MAX,
+				    PCI_IRQ_MSI | PCI_IRQ_MSIX);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "%s: multi MSI enablement failed\n",
+			__func__);
+		return ret;
+	}
+
+	/* For RX MSI */
+	for (i = 0; i < plat->rx_queues_to_use; i++)
+		res->rx_irq[i] =
+			pci_irq_vector(pdev,
+				       BRCM_XGMAC_MSI_RX_VECTOR_START + i * 2);
+
+	/* For TX MSI */
+	for (i = 0; i < plat->tx_queues_to_use; i++)
+		res->tx_irq[i] =
+			pci_irq_vector(pdev,
+				       BRCM_XGMAC_MSI_TX_VECTOR_START + i * 2);
+
+	res->irq = pci_irq_vector(pdev, BRCM_XGMAC_MSI_MAC_VECTOR);
+
+	plat->flags |= STMMAC_FLAG_MULTI_MSI_EN;
+	plat->flags |= STMMAC_FLAG_TSO_EN;
+
+	return 0;
+}
+
+static int dwxgmac_brcm_pci_probe(struct pci_dev *pdev,
+				  const struct pci_device_id *id)
+{
+	struct dwxgmac_brcm_pci_info *info =
+		(struct dwxgmac_brcm_pci_info *)id->driver_data;
+	struct plat_stmmacenet_data *plat;
+	struct brcm_priv_data *brcm_priv;
+	struct stmmac_resources res;
+	struct device *dev;
+	int rx_offset;
+	int tx_offset;
+	int vector;
+	int ret;
+
+	dev = &pdev->dev;
+
+	brcm_priv = devm_kzalloc(&pdev->dev, sizeof(*brcm_priv), GFP_KERNEL);
+	if (!brcm_priv)
+		return -ENOMEM;
+
+	plat = devm_kzalloc(&pdev->dev, sizeof(*plat), GFP_KERNEL);
+	if (!plat)
+		return -ENOMEM;
+
+	plat->dma_cfg = devm_kzalloc(&pdev->dev, sizeof(*plat->dma_cfg),
+				     GFP_KERNEL);
+	if (!plat->dma_cfg)
+		return -ENOMEM;
+
+	plat->axi = devm_kzalloc(&pdev->dev, sizeof(*plat->axi), GFP_KERNEL);
+	if (!plat->axi)
+		return -ENOMEM;
+
+	/* This device is directly attached to the switch chip internal to the
+	 * SoC using XGMII interface. Since no MDIO is present, register
+	 * fixed-link software_node to create phylink.
+	 */
+	plat->port_node = fwnode_create_software_node(NULL, NULL);
+	brcm_priv->fixed_link_node.name = fixed_link_node_name;
+	brcm_priv->fixed_link_node.properties = fixed_link_properties;
+	brcm_priv->fixed_link_node.parent = to_software_node(plat->port_node);
+	device_add_software_node(dev, &brcm_priv->fixed_link_node);
+
+	/* Disable D3COLD as our device does not support it */
+	pci_d3cold_disable(pdev);
+
+	/* Enable PCI device */
+	ret = pcim_enable_device(pdev);
+	if (ret) {
+		dev_err(&pdev->dev, "%s: ERROR: failed to enable device\n",
+			__func__);
+		return ret;
+	}
+
+	/* Get the base address of device */
+	ret = pcim_iomap_regions(pdev, BRCM_XGMAC_BAR0_MASK, pci_name(pdev));
+	if (ret)
+		return ret;
+	pci_set_master(pdev);
+
+	memset(&res, 0, sizeof(res));
+	res.addr = pcim_iomap_table(pdev)[0];
+	/* MISC Regs */
+	brcm_priv->misc_regs = res.addr + BRCM_XGMAC_IOMEM_MISC_REG_OFFSET;
+	/* MBOX Regs */
+	brcm_priv->mbox_regs = res.addr + BRCM_XGMAC_IOMEM_MBOX_REG_OFFSET;
+	/* XGMAC config Regs */
+	res.addr += BRCM_XGMAC_IOMEM_CFG_REG_OFFSET;
+	brcm_priv->xgmac_regs = res.addr;
+
+	plat->bsp_priv = brcm_priv;
+
+	ret = info->setup(pdev, plat);
+	if (ret)
+		return ret;
+
+	pci_write_config_dword(pdev, XGMAC_PCIE_CFG_MSIX_ADDR_MATCH_LOW,
+			       XGMAC_PCIE_CFG_MSIX_ADDR_MATCH_LO_VALUE);
+	pci_write_config_dword(pdev, XGMAC_PCIE_CFG_MSIX_ADDR_MATCH_HIGH,
+			       XGMAC_PCIE_CFG_MSIX_ADDR_MATCH_HI_VALUE);
+
+	misc_iowrite(brcm_priv, XGMAC_PCIE_MISC_MSIX_ADDR_MATCH_LO_OFFSET,
+		     XGMAC_PCIE_MISC_MSIX_ADDR_MATCH_LO_VALUE);
+	misc_iowrite(brcm_priv, XGMAC_PCIE_MISC_MSIX_ADDR_MATCH_HI_OFFSET,
+		     XGMAC_PCIE_MISC_MSIX_ADDR_MATCH_HI_VALUE);
+
+	/* SBD Interrupt */
+	misc_iowrite(brcm_priv, XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_SBD_ALL_OFFSET,
+		     XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_SBD_ALL_VALUE);
+	/* EP_DOORBELL Interrupt */
+	misc_iowrite(brcm_priv,
+		     XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_EP2HOST_DBELL_OFFSET,
+		     XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_EP2HOST_DBELL_VALUE);
+	/* EP_H0 Interrupt */
+	misc_iowrite(brcm_priv,
+		     XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_EP2HOST0_OFFSET,
+		     XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_EP2HOST0_VALUE);
+	/* EP_H1 Interrupt */
+	misc_iowrite(brcm_priv,
+		     XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_EP2HOST1_OFFSET,
+		     XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_EP2HOST1_VALUE);
+
+	rx_offset = XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_RX0_PF0_OFFSET;
+	tx_offset = XGMAC_PCIE_MISC_MSIX_VECTOR_MAP_TX0_PF0_OFFSET;
+	vector = BRCM_XGMAC_MSI_RX_VECTOR_START;
+	for (int i = 0; i < BRCM_MAX_DMA_CHANNEL_PAIRS; i++) {
+		/* RX Interrupt */
+		misc_iowrite(brcm_priv, rx_offset, vector++);
+		/* TX Interrupt */
+		misc_iowrite(brcm_priv, tx_offset, vector++);
+		rx_offset += 4;
+		tx_offset += 4;
+	}
+
+	/* Enable Switch Link */
+	misc_iowrite(brcm_priv, XGMAC_PCIE_MISC_MII_CTRL_OFFSET,
+		     XGMAC_PCIE_MISC_MII_CTRL_PAUSE_RX |
+		     XGMAC_PCIE_MISC_MII_CTRL_PAUSE_TX |
+		     XGMAC_PCIE_MISC_MII_CTRL_LINK_UP);
+	/* Enable MSI-X */
+	misc_iowrite(brcm_priv, XGMAC_PCIE_MISC_PCIESS_CTRL_OFFSET,
+		     XGMAC_PCIE_MISC_PCIESS_CTRL_EN_MSI_MSIX);
+
+	ret = brcm_config_multi_msi(pdev, plat, &res);
+	if (ret) {
+		dev_err(&pdev->dev,
+			"%s: ERROR: failed to enable IRQ\n", __func__);
+		goto err_disable_msi;
+	}
+
+	ret = stmmac_dvr_probe(&pdev->dev, plat, &res);
+	if (ret)
+		goto err_disable_msi;
+
+	return ret;
+
+err_disable_msi:
+	pci_free_irq_vectors(pdev);
+
+	return ret;
+}
+
+static void dwxgmac_brcm_software_node_remove(struct pci_dev *pdev)
+{
+	struct fwnode_handle *fwnode;
+	struct stmmac_priv *priv;
+	struct net_device *ndev;
+	struct device *dev;
+
+	dev = &pdev->dev;
+	ndev = dev_get_drvdata(dev);
+	priv = netdev_priv(ndev);
+	fwnode = priv->plat->port_node;
+
+	fwnode_remove_software_node(fwnode);
+	device_remove_software_node(dev);
+}
+
+static void dwxgmac_brcm_pci_remove(struct pci_dev *pdev)
+{
+	stmmac_dvr_remove(&pdev->dev);
+	pci_free_irq_vectors(pdev);
+	pcim_iounmap_regions(pdev, BRCM_XGMAC_BAR0_MASK);
+	pci_clear_master(pdev);
+	dwxgmac_brcm_software_node_remove(pdev);
+}
+
+static int __maybe_unused dwxgmac_brcm_pci_suspend(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	int ret;
+
+	ret = stmmac_suspend(dev);
+	if (ret)
+		return ret;
+
+	ret = pci_save_state(pdev);
+	if (ret)
+		return ret;
+
+	pci_disable_device(pdev);
+	pci_wake_from_d3(pdev, true);
+
+	return 0;
+}
+
+static int __maybe_unused dwxgmac_brcm_pci_resume(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct stmmac_priv *priv;
+	struct net_device *ndev;
+
+	ndev = dev_get_drvdata(dev);
+	priv = netdev_priv(ndev);
+	brcm_config_misc_regs(pdev, priv->plat->bsp_priv);
+
+	pci_restore_state(pdev);
+	pci_set_power_state(pdev, PCI_D0);
+
+	return stmmac_resume(dev);
+}
+
+static SIMPLE_DEV_PM_OPS(dwxgmac_brcm_pm_ops,
+			 dwxgmac_brcm_pci_suspend,
+			 dwxgmac_brcm_pci_resume);
+
+static const struct pci_device_id dwxgmac_brcm_id_table[] = {
+	{ PCI_DEVICE_DATA(BROADCOM, BCM8958X, &dwxgmac_brcm_pci_info) },
+	{}
+};
+
+MODULE_DEVICE_TABLE(pci, dwxgmac_brcm_id_table);
+
+static struct pci_driver dwxgmac_brcm_pci_driver = {
+	.name = "brcm-bcm8958x",
+	.id_table = dwxgmac_brcm_id_table,
+	.probe	= dwxgmac_brcm_pci_probe,
+	.remove = dwxgmac_brcm_pci_remove,
+	.driver = {
+		.pm = &dwxgmac_brcm_pm_ops,
+	},
+};
+
+module_pci_driver(dwxgmac_brcm_pci_driver);
+
+MODULE_DESCRIPTION("Broadcom 10G Automotive Ethernet PCIe driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index d3895d7eecfc..5b2ff7dbd47e 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -1040,6 +1040,32 @@  static void stmmac_mac_link_up(struct phylink_config *config,
 		default:
 			return;
 		}
+	} else if (interface == PHY_INTERFACE_MODE_XGMII) {
+		switch (speed) {
+		case SPEED_25000:
+			ctrl |= priv->hw->link.xgmii.speed25000;
+			break;
+		case SPEED_10000:
+			ctrl |= priv->hw->link.xgmii.speed10000;
+			break;
+		case SPEED_5000:
+			ctrl |= priv->hw->link.xgmii.speed5000;
+			break;
+		case SPEED_2500:
+			ctrl |= priv->hw->link.xgmii.speed2500;
+			break;
+		case SPEED_1000:
+			ctrl |= priv->hw->link.speed1000;
+			break;
+		case SPEED_100:
+			ctrl |= priv->hw->link.speed100;
+			break;
+		case SPEED_10:
+			ctrl |= priv->hw->link.speed10;
+			break;
+		default:
+			return;
+		}
 	} else if (interface == PHY_INTERFACE_MODE_XLGMII) {
 		switch (speed) {
 		case SPEED_100000: