| Message ID | 20241113101124.1279648-2-andrei.stefanescu@oss.nxp.com (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | gpio: siul2-s32g2: add initial GPIO driver | expand |
On Wed, Nov 13, 2024 at 12:10:53PM +0200, Andrei Stefanescu wrote: > Add the dt-bindings for the NXP SIUL2 module which is a multi > function device. It can export information about the SoC, configure > the pinmux&pinconf for pins and it is also a GPIO controller with > interrupt capability. > > Signed-off-by: Andrei Stefanescu <andrei.stefanescu@oss.nxp.com> > --- > .../bindings/mfd/nxp,s32g2-siul2.yaml | 165 ++++++++++++++++++ > 1 file changed, 165 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mfd/nxp,s32g2-siul2.yaml > > diff --git a/Documentation/devicetree/bindings/mfd/nxp,s32g2-siul2.yaml b/Documentation/devicetree/bindings/mfd/nxp,s32g2-siul2.yaml > new file mode 100644 > index 000000000000..a8edbea75bb6 > --- /dev/null > +++ b/Documentation/devicetree/bindings/mfd/nxp,s32g2-siul2.yaml > @@ -0,0 +1,165 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +# Copyright 2024 NXP > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/mfd/nxp,s32g2-siul2.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: NXP S32 System Integration Unit Lite2 (SIUL2) > + > +maintainers: > + - Andrei Stefanescu <andrei.stefanescu@oss.nxp.com> > + > +description: | > + SIUL2 is a hardware block which implements pinmuxing, > + pinconf, GPIOs (some with interrupt capability) and > + registers which contain information about the SoC. > + There are generally two SIUL2 modules whose functionality > + is grouped together. For example interrupt configuration > + registers are part of SIUL2_1 even though interrupts are > + also available for SIUL2_0 pins. > + > + The following register types are exported by SIUL2: > + - MIDR (MCU ID Register) - information related to the SoC > + - interrupt configuration registers > + - MSCR (Multiplexed Signal Configuration Register) - pinmuxing and pinconf > + - IMCR (Input Multiplexed Signal Configuration Register)- pinmuxing > + - PGPDO (Parallel GPIO Pad Data Out Register) - GPIO output value > + - PGPDI (Parallel GPIO Pad Data In Register) - GPIO input value > + > + Most registers are 32bit wide with the exception of PGPDO/PGPDI which are > + 16bit wide. > + > +properties: > + compatible: > + enum: > + - nxp,s32g2-siul2 > + - nxp,s32g3-siul2 > + > + reg: > + maxItems: 2 > + > + reg-names: > + items: > + - const: siul20 > + - const: siul21 > + > + gpio-controller: true > + > + "#gpio-cells": > + const: 2 > + > + gpio-ranges: > + maxItems: 2 > + > + gpio-reserved-ranges: > + maxItems: 2 > + > + interrupts: > + maxItems: 1 > + > + interrupt-controller: true > + > + "#interrupt-cells": > + const: 2 > + > + nvmem-layout: > + $ref: /schemas/nvmem/layouts/nvmem-layout.yaml# > + description: > + This container may reference an NVMEM layout parser. > + > +patternProperties: > + "-hog(-[0-9]+)?$": > + required: > + - gpio-hog > + > + "-pins$": > + type: object > + additionalProperties: false > + > + patternProperties: > + "-grp[0-9]$": > + type: object > + allOf: > + - $ref: /schemas/pinctrl/pinmux-node.yaml# > + - $ref: /schemas/pinctrl/pincfg-node.yaml# > + description: > + Pinctrl node's client devices specify pin muxes using subnodes, > + which in turn use the standard properties below. > + > + properties: > + bias-disable: true > + bias-high-impedance: true > + bias-pull-up: true > + bias-pull-down: true > + drive-open-drain: true > + input-enable: true > + output-enable: true > + > + pinmux: > + description: | > + An integer array for representing pinmux configurations of > + a device. Each integer consists of a PIN_ID and a 4-bit > + selected signal source(SSS) as IOMUX setting, which is > + calculated as: pinmux = (PIN_ID << 4 | SSS) > + > + slew-rate: > + description: Supported slew rate based on Fmax values (MHz) > + enum: [83, 133, 150, 166, 208] > + required: > + - pinmux > + > + additionalProperties: false There are $ref, need use unevaluatedProperties: false > + > +required: > + - compatible > + - reg > + - reg-names > + - gpio-controller > + - "#gpio-cells" > + - gpio-ranges > + - gpio-reserved-ranges > + - interrupts > + - interrupt-controller > + - "#interrupt-cells" > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/interrupt-controller/irq.h> > + > + siul2@4009c000 { generic node name, such as 'pinctrl' > + compatible = "nxp,s32g2-siul2"; > + reg = <0x4009c000 0x179c>, > + <0x44010000 0x17b0>; > + reg-names = "siul20", "siul21"; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&siul2 0 0 102>, <&siul2 112 112 79>; > + gpio-reserved-ranges = <102 10>, <123 21>; > + interrupt-controller; > + #interrupt-cells = <2>; > + interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>; > + > + jtag_pins: jtag-pins { needn't lable 'jtag_pins' in example. > + jtag-grp0 { > + pinmux = <0x0>; > + input-enable; > + bias-pull-up; > + slew-rate = <166>; > + }; > + }; > + > + nvmem-layout { > + compatible = "fixed-layout"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + soc-major@0 { > + reg = <0 0x4>; > + }; > + }; > + }; > +... > -- > 2.45.2 >
diff --git a/Documentation/devicetree/bindings/mfd/nxp,s32g2-siul2.yaml b/Documentation/devicetree/bindings/mfd/nxp,s32g2-siul2.yaml new file mode 100644 index 000000000000..a8edbea75bb6 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/nxp,s32g2-siul2.yaml @@ -0,0 +1,165 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright 2024 NXP +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/nxp,s32g2-siul2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP S32 System Integration Unit Lite2 (SIUL2) + +maintainers: + - Andrei Stefanescu <andrei.stefanescu@oss.nxp.com> + +description: | + SIUL2 is a hardware block which implements pinmuxing, + pinconf, GPIOs (some with interrupt capability) and + registers which contain information about the SoC. + There are generally two SIUL2 modules whose functionality + is grouped together. For example interrupt configuration + registers are part of SIUL2_1 even though interrupts are + also available for SIUL2_0 pins. + + The following register types are exported by SIUL2: + - MIDR (MCU ID Register) - information related to the SoC + - interrupt configuration registers + - MSCR (Multiplexed Signal Configuration Register) - pinmuxing and pinconf + - IMCR (Input Multiplexed Signal Configuration Register)- pinmuxing + - PGPDO (Parallel GPIO Pad Data Out Register) - GPIO output value + - PGPDI (Parallel GPIO Pad Data In Register) - GPIO input value + + Most registers are 32bit wide with the exception of PGPDO/PGPDI which are + 16bit wide. + +properties: + compatible: + enum: + - nxp,s32g2-siul2 + - nxp,s32g3-siul2 + + reg: + maxItems: 2 + + reg-names: + items: + - const: siul20 + - const: siul21 + + gpio-controller: true + + "#gpio-cells": + const: 2 + + gpio-ranges: + maxItems: 2 + + gpio-reserved-ranges: + maxItems: 2 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + nvmem-layout: + $ref: /schemas/nvmem/layouts/nvmem-layout.yaml# + description: + This container may reference an NVMEM layout parser. + +patternProperties: + "-hog(-[0-9]+)?$": + required: + - gpio-hog + + "-pins$": + type: object + additionalProperties: false + + patternProperties: + "-grp[0-9]$": + type: object + allOf: + - $ref: /schemas/pinctrl/pinmux-node.yaml# + - $ref: /schemas/pinctrl/pincfg-node.yaml# + description: + Pinctrl node's client devices specify pin muxes using subnodes, + which in turn use the standard properties below. + + properties: + bias-disable: true + bias-high-impedance: true + bias-pull-up: true + bias-pull-down: true + drive-open-drain: true + input-enable: true + output-enable: true + + pinmux: + description: | + An integer array for representing pinmux configurations of + a device. Each integer consists of a PIN_ID and a 4-bit + selected signal source(SSS) as IOMUX setting, which is + calculated as: pinmux = (PIN_ID << 4 | SSS) + + slew-rate: + description: Supported slew rate based on Fmax values (MHz) + enum: [83, 133, 150, 166, 208] + required: + - pinmux + + additionalProperties: false + +required: + - compatible + - reg + - reg-names + - gpio-controller + - "#gpio-cells" + - gpio-ranges + - gpio-reserved-ranges + - interrupts + - interrupt-controller + - "#interrupt-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + siul2@4009c000 { + compatible = "nxp,s32g2-siul2"; + reg = <0x4009c000 0x179c>, + <0x44010000 0x17b0>; + reg-names = "siul20", "siul21"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&siul2 0 0 102>, <&siul2 112 112 79>; + gpio-reserved-ranges = <102 10>, <123 21>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>; + + jtag_pins: jtag-pins { + jtag-grp0 { + pinmux = <0x0>; + input-enable; + bias-pull-up; + slew-rate = <166>; + }; + }; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + soc-major@0 { + reg = <0 0x4>; + }; + }; + }; +...
Add the dt-bindings for the NXP SIUL2 module which is a multi function device. It can export information about the SoC, configure the pinmux&pinconf for pins and it is also a GPIO controller with interrupt capability. Signed-off-by: Andrei Stefanescu <andrei.stefanescu@oss.nxp.com> --- .../bindings/mfd/nxp,s32g2-siul2.yaml | 165 ++++++++++++++++++ 1 file changed, 165 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/nxp,s32g2-siul2.yaml