[net-next,RFC,5/5] net: phy: dp83822: Add support for phy_port representation

Commit Message

Maxime Chevallier Dec. 20, 2024, 8:15 p.m. UTC

With the phy_port representation intrduced, we can use .attach_port to
populate the port information based on either the straps or the
ti,fiber-mode property. This allows simplifying the probe function and
allow users to override the strapping configuration.

Signed-off-by: Maxime Chevallier <[e-mail]>
---
 drivers/net/phy/dp83822.c | 60 +++++++++++++++++++++++++--------------
 1 file changed, 39 insertions(+), 21 deletions(-)

Patch

diff --git a/drivers/net/phy/dp83822.c b/drivers/net/phy/dp83822.c
index 334c17a68edd..96a0ad1a0e83 100644
--- a/drivers/net/phy/dp83822.c
+++ b/drivers/net/phy/dp83822.c
@@ -637,17 +637,6 @@  static int dp83822_of_init(struct phy_device *phydev)
 	struct device *dev = &phydev->mdio.dev;
 	const char *of_val;
 
-	/* Signal detection for the PHY is only enabled if the FX_EN and the
-	 * SD_EN pins are strapped. Signal detection can only enabled if FX_EN
-	 * is strapped otherwise signal detection is disabled for the PHY.
-	 */
-	if (dp83822->fx_enabled && dp83822->fx_sd_enable)
-		dp83822->fx_signal_det_low = device_property_present(dev,
-								     "ti,link-loss-low");
-	if (!dp83822->fx_enabled)
-		dp83822->fx_enabled = device_property_present(dev,
-							      "ti,fiber-mode");
-
 	if (!device_property_read_string(dev, "ti,gpio2-clk-out", &of_val)) {
 		if (strcmp(of_val, "mac-if") == 0) {
 			dp83822->gpio2_clk_out = DP83822_CLK_SRC_MAC_IF;
@@ -740,6 +729,44 @@  static int dp83822_read_straps(struct phy_device *phydev)
 	return 0;
 }
 
+static int dp83822_attach_port(struct phy_device *phydev, struct phy_port *port)
+{
+	struct dp83822_private *dp83822 = phydev->priv;
+	struct device *dev = &phydev->mdio.dev;
+	int ret;
+
+	if (port->mediums) {
+		if (phy_port_is_fiber(port) ||
+		    port->mediums & BIT(ETHTOOL_LINK_MEDIUM_BASEX))
+			dp83822->fx_enabled = true;
+	} else {
+		ret = dp83822_read_straps(phydev);
+		if (ret)
+			return ret;
+
+#ifdef CONFIG_OF_MDIO
+		if (dp83822->fx_enabled && dp83822->fx_sd_enable)
+			dp83822->fx_signal_det_low =
+				device_property_present(dev, "ti,link-loss-low");
+		if (!dp83822->fx_enabled)
+			dp83822->fx_enabled =
+				device_property_present(dev, "ti,fiber-mode");
+#endif
+
+		if (dp83822->fx_enabled) {
+			port->lanes = 1;
+			port->mediums = BIT(ETHTOOL_LINK_MEDIUM_BASEF) |
+					BIT(ETHTOOL_LINK_MEDIUM_BASEX);
+		} else {
+			/* This PHY can only to 100BaseTX max, so on 2 lanes */
+			port->lanes = 2;
+			port->mediums = BIT(ETHTOOL_LINK_MEDIUM_BASET);
+		}
+	}
+
+	return 0;
+}
+
 static int dp8382x_probe(struct phy_device *phydev)
 {
 	struct dp83822_private *dp83822;
@@ -756,24 +783,14 @@  static int dp8382x_probe(struct phy_device *phydev)
 
 static int dp83822_probe(struct phy_device *phydev)
 {
-	struct dp83822_private *dp83822;
 	int ret;
 
 	ret = dp8382x_probe(phydev);
 	if (ret)
 		return ret;
 
-	dp83822 = phydev->priv;
-
-	ret = dp83822_read_straps(phydev);
-	if (ret)
-		return ret;
-
 	dp83822_of_init(phydev);
 
-	if (dp83822->fx_enabled)
-		phydev->port = PORT_FIBRE;
-
 	return 0;
 }
 
@@ -831,6 +848,7 @@  static int dp83822_resume(struct phy_device *phydev)
 		.handle_interrupt = dp83822_handle_interrupt,	\
 		.suspend = dp83822_suspend,			\
 		.resume = dp83822_resume,			\
+		.attach_port = dp83822_attach_port		\
 	}
 
 #define DP83825_PHY_DRIVER(_id, _name)				\