new file mode 100644
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Apple S8000/S8003 "A9" SoC
+ *
+ * This file contains parts common to both variants of A9
+ *
+ * Copyright (c) 2022, Konrad Dybcio <konradybcio@kernel.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/apple-aic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/apple.h>
+
+/ {
+ interrupt-parent = <&aic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clkref: clock-ref {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ clock-output-names = "clkref";
+ };
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "apple,twister";
+ reg = <0x0 0x0>;
+ cpu-release-addr = <0 0>; /* To be filled in by loader */
+ enable-method = "spin-table";
+ device_type = "cpu";
+ };
+
+ cpu1: cpu@1 {
+ compatible = "apple,twister";
+ reg = <0x0 0x1>;
+ cpu-release-addr = <0 0>; /* To be filled in by loader */
+ enable-method = "spin-table";
+ device_type = "cpu";
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ nonposted-mmio;
+ ranges;
+
+ serial0: serial@20a0c0000 {
+ compatible = "apple,s5l-uart";
+ reg = <0x2 0x0a0c0000 0x0 0x4000>;
+ reg-io-width = <4>;
+ interrupt-parent = <&aic>;
+ interrupts = <AIC_IRQ 192 IRQ_TYPE_LEVEL_HIGH>;
+ /* Use the bootloader-enabled clocks for now. */
+ clocks = <&clkref>, <&clkref>;
+ clock-names = "uart", "clk_uart_baud0";
+ status = "disabled";
+ };
+
+ aic: interrupt-controller@20e100000 {
+ compatible = "apple,s8000-aic", "apple,aic";
+ reg = <0x2 0x0e100000 0x0 0x100000>;
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ };
+
+ pinctrl_ap: pinctrl@20f100000 {
+ compatible = "apple,s8000-pinctrl", "apple,pinctrl";
+ reg = <0x2 0x0f100000 0x0 0x100000>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl_ap 0 0 208>;
+ apple,npins = <208>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&aic>;
+ interrupts = <AIC_IRQ 42 IRQ_TYPE_LEVEL_HIGH>,
+ <AIC_IRQ 43 IRQ_TYPE_LEVEL_HIGH>,
+ <AIC_IRQ 44 IRQ_TYPE_LEVEL_HIGH>,
+ <AIC_IRQ 45 IRQ_TYPE_LEVEL_HIGH>,
+ <AIC_IRQ 46 IRQ_TYPE_LEVEL_HIGH>,
+ <AIC_IRQ 47 IRQ_TYPE_LEVEL_HIGH>,
+ <AIC_IRQ 48 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pinctrl_aop: pinctrl@2100f0000 {
+ compatible = "apple,s8000-pinctrl", "apple,pinctrl";
+ reg = <0x2 0x100f0000 0x0 0x100000>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl_aop 0 0 42>;
+ apple,npins = <42>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&aic>;
+ interrupts = <AIC_IRQ 113 IRQ_TYPE_LEVEL_HIGH>,
+ <AIC_IRQ 114 IRQ_TYPE_LEVEL_HIGH>,
+ <AIC_IRQ 115 IRQ_TYPE_LEVEL_HIGH>,
+ <AIC_IRQ 116 IRQ_TYPE_LEVEL_HIGH>,
+ <AIC_IRQ 117 IRQ_TYPE_LEVEL_HIGH>,
+ <AIC_IRQ 118 IRQ_TYPE_LEVEL_HIGH>,
+ <AIC_IRQ 119 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ wdt: watchdog@2102b0000 {
+ compatible = "apple,s8000-wdt", "apple,wdt";
+ reg = <0x2 0x102b0000 0x0 0x4000>;
+ clocks = <&clkref>;
+ interrupt-parent = <&aic>;
+ interrupts = <AIC_IRQ 4 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&aic>;
+ interrupt-names = "phys", "virt";
+ /* Note that A9 doesn't actually have a hypervisor (EL2 is not implemented). */
+ interrupts = <AIC_FIQ AIC_TMR_GUEST_PHYS IRQ_TYPE_LEVEL_HIGH>,
+ <AIC_FIQ AIC_TMR_GUEST_VIRT IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
+/*
+ * The A9 was made by two separate fabs on two different process
+ * nodes: Samsung made the S8000 (APL0898) on 14nm and TSMC made
+ * the S8003 (APL1022) on 16nm. There are some minor differences
+ * such as timing in cpufreq state transistions.
+ */
@@ -7,138 +7,11 @@
* Copyright (c) 2022, Konrad Dybcio <konradybcio@kernel.org>
*/
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/apple-aic.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/apple.h>
-
-/ {
- interrupt-parent = <&aic>;
- #address-cells = <2>;
- #size-cells = <2>;
-
- clkref: clock-ref {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <24000000>;
- clock-output-names = "clkref";
- };
-
- cpus {
- #address-cells = <2>;
- #size-cells = <0>;
-
- cpu0: cpu@0 {
- compatible = "apple,twister";
- reg = <0x0 0x0>;
- cpu-release-addr = <0 0>; /* To be filled in by loader */
- enable-method = "spin-table";
- device_type = "cpu";
- };
-
- cpu1: cpu@1 {
- compatible = "apple,twister";
- reg = <0x0 0x1>;
- cpu-release-addr = <0 0>; /* To be filled in by loader */
- enable-method = "spin-table";
- device_type = "cpu";
- };
- };
-
- soc {
- compatible = "simple-bus";
- #address-cells = <2>;
- #size-cells = <2>;
- nonposted-mmio;
- ranges;
-
- serial0: serial@20a0c0000 {
- compatible = "apple,s5l-uart";
- reg = <0x2 0x0a0c0000 0x0 0x4000>;
- reg-io-width = <4>;
- interrupt-parent = <&aic>;
- interrupts = <AIC_IRQ 192 IRQ_TYPE_LEVEL_HIGH>;
- /* Use the bootloader-enabled clocks for now. */
- clocks = <&clkref>, <&clkref>;
- clock-names = "uart", "clk_uart_baud0";
- status = "disabled";
- };
-
- aic: interrupt-controller@20e100000 {
- compatible = "apple,s8000-aic", "apple,aic";
- reg = <0x2 0x0e100000 0x0 0x100000>;
- #interrupt-cells = <3>;
- interrupt-controller;
- };
-
- pinctrl_ap: pinctrl@20f100000 {
- compatible = "apple,s8000-pinctrl", "apple,pinctrl";
- reg = <0x2 0x0f100000 0x0 0x100000>;
-
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&pinctrl_ap 0 0 208>;
- apple,npins = <208>;
-
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupt-parent = <&aic>;
- interrupts = <AIC_IRQ 42 IRQ_TYPE_LEVEL_HIGH>,
- <AIC_IRQ 43 IRQ_TYPE_LEVEL_HIGH>,
- <AIC_IRQ 44 IRQ_TYPE_LEVEL_HIGH>,
- <AIC_IRQ 45 IRQ_TYPE_LEVEL_HIGH>,
- <AIC_IRQ 46 IRQ_TYPE_LEVEL_HIGH>,
- <AIC_IRQ 47 IRQ_TYPE_LEVEL_HIGH>,
- <AIC_IRQ 48 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- pinctrl_aop: pinctrl@2100f0000 {
- compatible = "apple,s8000-pinctrl", "apple,pinctrl";
- reg = <0x2 0x100f0000 0x0 0x100000>;
-
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&pinctrl_aop 0 0 42>;
- apple,npins = <42>;
-
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupt-parent = <&aic>;
- interrupts = <AIC_IRQ 113 IRQ_TYPE_LEVEL_HIGH>,
- <AIC_IRQ 114 IRQ_TYPE_LEVEL_HIGH>,
- <AIC_IRQ 115 IRQ_TYPE_LEVEL_HIGH>,
- <AIC_IRQ 116 IRQ_TYPE_LEVEL_HIGH>,
- <AIC_IRQ 117 IRQ_TYPE_LEVEL_HIGH>,
- <AIC_IRQ 118 IRQ_TYPE_LEVEL_HIGH>,
- <AIC_IRQ 119 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- wdt: watchdog@2102b0000 {
- compatible = "apple,s8000-wdt", "apple,wdt";
- reg = <0x2 0x102b0000 0x0 0x4000>;
- clocks = <&clkref>;
- interrupt-parent = <&aic>;
- interrupts = <AIC_IRQ 4 IRQ_TYPE_LEVEL_HIGH>;
- };
- };
-
- timer {
- compatible = "arm,armv8-timer";
- interrupt-parent = <&aic>;
- interrupt-names = "phys", "virt";
- /* Note that A9 doesn't actually have a hypervisor (EL2 is not implemented). */
- interrupts = <AIC_FIQ AIC_TMR_GUEST_PHYS IRQ_TYPE_LEVEL_HIGH>,
- <AIC_FIQ AIC_TMR_GUEST_VIRT IRQ_TYPE_LEVEL_HIGH>;
- };
-};
+#include "s800-0-3.dtsi"
/*
* The A9 was made by two separate fabs on two different process
* nodes: Samsung made the S8000 (APL0898) on 14nm and TSMC made
- * the S8003 (APL1022) on 16nm. While they are seemingly the same,
- * they do have distinct part numbers and devices using them have
- * distinct model names. There are currently no known differences
- * between these as far as Linux is concerned, but let's keep things
- * structured properly to make it easier to alter the behaviour of
- * one of the chips if need be.
+ * the S8003 (APL1022) on 16nm. There are some minor differences
+ * such as timing in cpufreq state transistions.
*/
@@ -7,15 +7,11 @@
* Copyright (c) 2022, Konrad Dybcio <konradybcio@kernel.org>
*/
-#include "s8000.dtsi"
+#include "s800-0-3.dtsi"
/*
* The A9 was made by two separate fabs on two different process
* nodes: Samsung made the S8000 (APL0898) on 14nm and TSMC made
- * the S8003 (APL1022) on 16nm. While they are seemingly the same,
- * they do have distinct part numbers and devices using them have
- * distinct model names. There are currently no known differences
- * between these as far as Linux is concerned, but let's keep things
- * structured properly to make it easier to alter the behaviour of
- * one of the chips if need be.
+ * the S8003 (APL1022) on 16nm. There are some minor differences
+ * such as timing in cpufreq state transistions.
*/
Despite what the code comments said, the DTS files were not split properly. Since these two SoCs are now known to have minor differences like in latencies for cpufreq state transistions, split the DTS files now. Signed-off-by: Nick Chan <towinchenmi@gmail.com> --- Changes since v1: - Drop PMGR nodes file rename. This is now the first patch and other series that modifies Apple A9 DTS files now depend on this series. Link to v1: https://lore.kernel.org/asahi/20241206135051.56049-1-towinchenmi@gmail.com/T Nick Chan arch/arm64/boot/dts/apple/s800-0-3.dtsi | 140 ++++++++++++++++++++++++ arch/arm64/boot/dts/apple/s8000.dtsi | 133 +--------------------- arch/arm64/boot/dts/apple/s8003.dtsi | 10 +- 3 files changed, 146 insertions(+), 137 deletions(-) create mode 100644 arch/arm64/boot/dts/apple/s800-0-3.dtsi base-commit: 78d4f34e2115b517bcbfe7ec0d018bbbb6f9b0b8