| Message ID | 20250102171424.3644-1-lukas.schmid@netcube.li (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | [v2,1/3] dt-bindings: vendor-prefixes: Add NetCube Systems Austria name | expand |
On Fri, Jan 3, 2025 at 1:17 AM Lukas Schmid <lukas.schmid@netcube.li> wrote: > > NetCube Systems Kumquat is a board based on the Allwinner V3s SoC, > including: > > - 64MB DDR2 included in SoC > - 10/100 Mbps Ethernet > - USB-C DRD > - Audio Codec > - Isolated CAN-FD > - ESP32 over SDIO > - 8MB SPI-NOR Flash for bootloader > - I2C EEPROM for MAC addresses > - SDIO Connector for eMMC or SD-Card > - 8x 12/24V IOs, 4x normally open relays > - DS3232 RTC > - QWIIC connectors for external I2C devices > > Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li> This seems to be a new version. Please tag the patches with a newer version. `git format-patch -v2` can do that for you. And please include a changelog listing the changes between this and the previous version. Last, please send the whole series, not just a single patch. ChenYu
On Thu, 2 Jan 2025 17:14:21 +0000 Lukas Schmid <lukas.schmid@netcube.li> wrote: Hi, > NetCube Systems Kumquat is a board based on the Allwinner V3s SoC, > including: Please do not just resend single patches out of a series, and always update the patch version in the subject - your previous series should have been v2 already, so that one here would would be: [PATCH v3 3/3] ARM: dts: sunxi: .... Also please summarise your changes at an appropriate location, for individual patches after the "three dashes" (after your Signed-off-by: below), or for all patches in a cover letter. Git can partly take care of those things for you: $ git format-patch -3 -v3 --cover-letter You will need to "just" fill the generated cover letter file, and send all of the files again. In general it's customary to wait for at least a day (ideally more) before sending a new revision, to allow people from other time zones to comment. So in this case here I think you should send a v3 of all patches tomorrow or on the weekend, that would make it obvious that the other patches are now obsolete. Also make sure to include Krzysztof's ACKs for patch 1 and 2. Documentation/process/submitting-patches.rst has some more tips. Cheers, Andre > > - 64MB DDR2 included in SoC > - 10/100 Mbps Ethernet > - USB-C DRD > - Audio Codec > - Isolated CAN-FD > - ESP32 over SDIO > - 8MB SPI-NOR Flash for bootloader > - I2C EEPROM for MAC addresses > - SDIO Connector for eMMC or SD-Card > - 8x 12/24V IOs, 4x normally open relays > - DS3232 RTC > - QWIIC connectors for external I2C devices > > Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li> > --- > arch/arm/boot/dts/allwinner/Makefile | 2 + > .../allwinner/sun8i-v3s-netcube-kumquat.dts | 286 ++++++++++++++++++ > arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi | 6 + > 3 files changed, 294 insertions(+) > create mode 100644 arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts > > diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile > index 48666f73e638..d799ad153b37 100644 > --- a/arch/arm/boot/dts/allwinner/Makefile > +++ b/arch/arm/boot/dts/allwinner/Makefile > @@ -199,6 +199,7 @@ DTC_FLAGS_sun8i-h3-nanopi-r1 := -@ > DTC_FLAGS_sun8i-h3-orangepi-pc := -@ > DTC_FLAGS_sun8i-h3-bananapi-m2-plus-v1.2 := -@ > DTC_FLAGS_sun8i-h3-orangepi-pc-plus := -@ > +DTC_FLAGS_sun8i-v3s-netcube-kumquat := -@ > dtb-$(CONFIG_MACH_SUN8I) += \ > sun8i-a23-evb.dtb \ > sun8i-a23-gt90h-v4.dtb \ > @@ -261,6 +262,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ > sun8i-v3s-anbernic-rg-nano.dtb \ > sun8i-v3s-licheepi-zero.dtb \ > sun8i-v3s-licheepi-zero-dock.dtb \ > + sun8i-v3s-netcube-kumquat.dtb \ > sun8i-v40-bananapi-m2-berry.dtb > dtb-$(CONFIG_MACH_SUN9I) += \ > sun9i-a80-optimus.dtb \ > diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts > new file mode 100644 > index 000000000000..e3e34d904c23 > --- /dev/null > +++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts > @@ -0,0 +1,286 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li> > + */ > + > +/dts-v1/; > +#include "sun8i-v3s.dtsi" > + > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/gpio/gpio.h> > + > +/{ > + model = "NetCube Systems Kumquat"; > + compatible = "netcube,kumquat", "allwinner,sun8i-v3s"; > + > + aliases { > + serial0 = &uart0; > + ethernet0 = &emac; > + rtc0 = &ds3232; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + led-heartbeat { > + gpios = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */ > + linux,default-trigger = "heartbeat"; > + color = <LED_COLOR_ID_GREEN>; > + function = LED_FUNCTION_HEARTBEAT; > + }; > + > + led-mmc0-act { > + gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ > + linux,default-trigger = "mmc0"; > + color = <LED_COLOR_ID_GREEN>; > + function = LED_FUNCTION_DISK; > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + autorepeat; > + > + key-user { > + label = "GPIO Key User"; > + linux,code = <KEY_PROG1>; > + gpios = <&pio 1 2 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PB2 */ > + }; > + }; > + > + /* K7805-1000R3 Switching Regulator supplied from main 12/24V terminal block */ > + reg_vcc5v0: regulator-5v0 { > + compatible = "regulator-fixed"; > + regulator-name = "vcc5v0"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + }; > + > + /* EA3036C Switching 3 Channel Regulator - Channel 2 */ > + reg_vcc3v3: regulator-3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "vcc3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <®_vcc5v0>; > + }; > + > + /* XC6206-3.0 Linear Regualtor */ > + reg_vcc3v0: regulator-3v0 { > + compatible = "regulator-fixed"; > + regulator-name = "vcc3v0"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + vin-supply = <®_vcc3v3>; > + }; > + > + /* 40 MHz Crystal Oscillator on PCB */ > + clk_can0: clock-can0 { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <40000000>; > + }; > +}; > + > +&mmc0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc0_pins>; > + vmmc-supply = <®_vcc3v3>; > + bus-width = <4>; > + broken-cd; > + status = "okay"; > +}; > + > +&mmc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc1_pins>; > + vmmc-supply = <®_vcc3v3>; > + bus-width = <4>; > + broken-cd; > + status = "okay"; > +}; > + > +&usb_otg { > + extcon = <&tusb320 0>; > + dr_mode = "otg"; > + status = "okay"; > +}; > + > +&usbphy { > + usb0_id_det-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ > + status = "okay"; > +}; > + > +&ehci { > + status = "okay"; > +}; > + > +&ohci { > + status = "okay"; > +}; > + > +&lradc { > + vref-supply = <®_vcc3v0>; > + status = "okay"; > +}; > + > +&codec { > + allwinner,audio-routing = > + "Headphone", "HP", > + "Headphone", "HPCOM", > + "MIC1", "Mic", > + "Mic", "HBIAS"; > + status = "okay"; > +}; > + > +&uart0 { > + pinctrl-0 = <&uart0_pb_pins>; > + pinctrl-names = "default"; > + status = "okay"; > +}; > + > +&uart1 { > + pinctrl-0 = <&uart1_pe_pins>; > + pinctrl-names = "default"; > + status = "okay"; > +}; > + > +&i2c0 { > + pinctrl-0 = <&i2c0_pins>; > + pinctrl-names = "default"; > + status = "okay"; > + > + eeprom0: eeprom@50 { > + compatible = "atmel,24c02"; /* actually it's a 24AA02E48 */ > + pagesize = <16>; > + read-only; > + reg = <0x50>; > + vcc-supply = <®_vcc3v3>; > + > + #address-cells = <1>; > + #size-cells = <1>; > + > + eth0_macaddress: macaddress@fa { > + reg = <0xfa 0x06>; > + }; > + }; > + > + tusb320: typec@60 { > + compatible = "ti,tusb320"; > + reg = <0x60>; > + interrupt-parent = <&pio>; > + interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; > + }; > + > + ds3232: rtc@68 { > + compatible = "dallas,ds3232"; > + reg = <0x68>; > + }; > +}; > + > +&emac { > + allwinner,leds-active-low; > + nvmem-cells = <ð0_macaddress>; /* custom nvmem reference */ > + nvmem-cell-names = "mac-address"; /* see ethernet-controller.yaml */ > + status = "okay"; > +}; > + > +&spi0 { > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&spi0_pins>; > + cs-gpios = <0>, <&pio 1 0 GPIO_ACTIVE_LOW>; /* PB0 */ > + status = "okay"; > + > + flash@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "jedec,spi-nor"; > + reg = <0>; > + label = "firmware"; > + spi-max-frequency = <40000000>; > + }; > + > + can@1 { > + compatible = "microchip,mcp2518fd"; > + reg = <1>; > + clocks = <&clk_can0>; > + interrupt-parent = <&pio>; > + interrupts = <1 1 IRQ_TYPE_LEVEL_LOW>; /* PB1 */ > + spi-max-frequency = <20000000>; > + vdd-supply = <®_vcc3v3>; > + xceiver-supply = <®_vcc3v3>; > + }; > +}; > + > +&pio { > + vcc-pb-supply = <®_vcc3v3>; > + vcc-pc-supply = <®_vcc3v3>; > + vcc-pe-supply = <®_vcc3v3>; > + vcc-pf-supply = <®_vcc3v3>; > + vcc-pg-supply = <®_vcc3v3>; > + > + gpio-reserved-ranges = <0 32>, <42 22>, <68 28>, <96 32>, <153 7>, <167 25>, <198 26>; > + gpio-line-names = "", "", "", "", // PA > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "CAN_nCS", "CAN_nINT", "USER_SW", "PB3", // PB > + "USB_ID", "USBC_nINT", "I2C0_SCL", "I2C0_SDA", > + "UART0_TX", "UART0_RX", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "SPI_MISO", "SPI_SCK", "FLASH_nCS", "SPI_MOSI", // PC > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", // PD > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "Q12", "Q11", "Q10", "Q9", // PE > + "LED_SYS0", "I1", "Q1", "Q2", > + "I2", "I3", "Q3", "Q4", > + "I4", "I5", "Q5", "Q6", > + "I6", "I7", "Q7", "Q8", > + "I8", "UART1_TXD", "UART1_RXD", "ESP_nRST", > + "ESP_nBOOT", "", "", "", > + "", "", "", "", > + "SD_D1", "SD_D0", "SD_CLK", "SD_CMD", // PF > + "SD_D3", "SD_D2", "LED_SYS1", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "ESP_CLK", "ESP_CMD", "ESP_D0", "ESP_D1", // PG > + "ESP_D2", "ESP_D3", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", "", > + "", "", "", ""; > +}; > diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi > index 9e13c2aa8911..f909b1d4dbca 100644 > --- a/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi > +++ b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi > @@ -416,6 +416,12 @@ uart0_pb_pins: uart0-pb-pins { > function = "uart0"; > }; > > + /omit-if-no-ref/ > + uart1_pe_pins: uart1-pe-pins { > + pins = "PE21", "PE22"; > + function = "uart1"; > + }; > + > uart2_pins: uart2-pins { > pins = "PB0", "PB1"; > function = "uart2";
diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile index 48666f73e638..d799ad153b37 100644 --- a/arch/arm/boot/dts/allwinner/Makefile +++ b/arch/arm/boot/dts/allwinner/Makefile @@ -199,6 +199,7 @@ DTC_FLAGS_sun8i-h3-nanopi-r1 := -@ DTC_FLAGS_sun8i-h3-orangepi-pc := -@ DTC_FLAGS_sun8i-h3-bananapi-m2-plus-v1.2 := -@ DTC_FLAGS_sun8i-h3-orangepi-pc-plus := -@ +DTC_FLAGS_sun8i-v3s-netcube-kumquat := -@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-a23-evb.dtb \ sun8i-a23-gt90h-v4.dtb \ @@ -261,6 +262,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-v3s-anbernic-rg-nano.dtb \ sun8i-v3s-licheepi-zero.dtb \ sun8i-v3s-licheepi-zero-dock.dtb \ + sun8i-v3s-netcube-kumquat.dtb \ sun8i-v40-bananapi-m2-berry.dtb dtb-$(CONFIG_MACH_SUN9I) += \ sun9i-a80-optimus.dtb \ diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts new file mode 100644 index 000000000000..e3e34d904c23 --- /dev/null +++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts @@ -0,0 +1,286 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li> + */ + +/dts-v1/; +#include "sun8i-v3s.dtsi" + +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/gpio/gpio.h> + +/{ + model = "NetCube Systems Kumquat"; + compatible = "netcube,kumquat", "allwinner,sun8i-v3s"; + + aliases { + serial0 = &uart0; + ethernet0 = &emac; + rtc0 = &ds3232; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led-heartbeat { + gpios = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */ + linux,default-trigger = "heartbeat"; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_HEARTBEAT; + }; + + led-mmc0-act { + gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ + linux,default-trigger = "mmc0"; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_DISK; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + autorepeat; + + key-user { + label = "GPIO Key User"; + linux,code = <KEY_PROG1>; + gpios = <&pio 1 2 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PB2 */ + }; + }; + + /* K7805-1000R3 Switching Regulator supplied from main 12/24V terminal block */ + reg_vcc5v0: regulator-5v0 { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + /* EA3036C Switching 3 Channel Regulator - Channel 2 */ + reg_vcc3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <®_vcc5v0>; + }; + + /* XC6206-3.0 Linear Regualtor */ + reg_vcc3v0: regulator-3v0 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v0"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + vin-supply = <®_vcc3v3>; + }; + + /* 40 MHz Crystal Oscillator on PCB */ + clk_can0: clock-can0 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <40000000>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + broken-cd; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + broken-cd; + status = "okay"; +}; + +&usb_otg { + extcon = <&tusb320 0>; + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ + status = "okay"; +}; + +&ehci { + status = "okay"; +}; + +&ohci { + status = "okay"; +}; + +&lradc { + vref-supply = <®_vcc3v0>; + status = "okay"; +}; + +&codec { + allwinner,audio-routing = + "Headphone", "HP", + "Headphone", "HPCOM", + "MIC1", "Mic", + "Mic", "HBIAS"; + status = "okay"; +}; + +&uart0 { + pinctrl-0 = <&uart0_pb_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&uart1 { + pinctrl-0 = <&uart1_pe_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&i2c0 { + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + status = "okay"; + + eeprom0: eeprom@50 { + compatible = "atmel,24c02"; /* actually it's a 24AA02E48 */ + pagesize = <16>; + read-only; + reg = <0x50>; + vcc-supply = <®_vcc3v3>; + + #address-cells = <1>; + #size-cells = <1>; + + eth0_macaddress: macaddress@fa { + reg = <0xfa 0x06>; + }; + }; + + tusb320: typec@60 { + compatible = "ti,tusb320"; + reg = <0x60>; + interrupt-parent = <&pio>; + interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; + }; + + ds3232: rtc@68 { + compatible = "dallas,ds3232"; + reg = <0x68>; + }; +}; + +&emac { + allwinner,leds-active-low; + nvmem-cells = <ð0_macaddress>; /* custom nvmem reference */ + nvmem-cell-names = "mac-address"; /* see ethernet-controller.yaml */ + status = "okay"; +}; + +&spi0 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins>; + cs-gpios = <0>, <&pio 1 0 GPIO_ACTIVE_LOW>; /* PB0 */ + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + label = "firmware"; + spi-max-frequency = <40000000>; + }; + + can@1 { + compatible = "microchip,mcp2518fd"; + reg = <1>; + clocks = <&clk_can0>; + interrupt-parent = <&pio>; + interrupts = <1 1 IRQ_TYPE_LEVEL_LOW>; /* PB1 */ + spi-max-frequency = <20000000>; + vdd-supply = <®_vcc3v3>; + xceiver-supply = <®_vcc3v3>; + }; +}; + +&pio { + vcc-pb-supply = <®_vcc3v3>; + vcc-pc-supply = <®_vcc3v3>; + vcc-pe-supply = <®_vcc3v3>; + vcc-pf-supply = <®_vcc3v3>; + vcc-pg-supply = <®_vcc3v3>; + + gpio-reserved-ranges = <0 32>, <42 22>, <68 28>, <96 32>, <153 7>, <167 25>, <198 26>; + gpio-line-names = "", "", "", "", // PA + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "CAN_nCS", "CAN_nINT", "USER_SW", "PB3", // PB + "USB_ID", "USBC_nINT", "I2C0_SCL", "I2C0_SDA", + "UART0_TX", "UART0_RX", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "SPI_MISO", "SPI_SCK", "FLASH_nCS", "SPI_MOSI", // PC + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", // PD + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "Q12", "Q11", "Q10", "Q9", // PE + "LED_SYS0", "I1", "Q1", "Q2", + "I2", "I3", "Q3", "Q4", + "I4", "I5", "Q5", "Q6", + "I6", "I7", "Q7", "Q8", + "I8", "UART1_TXD", "UART1_RXD", "ESP_nRST", + "ESP_nBOOT", "", "", "", + "", "", "", "", + "SD_D1", "SD_D0", "SD_CLK", "SD_CMD", // PF + "SD_D3", "SD_D2", "LED_SYS1", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "ESP_CLK", "ESP_CMD", "ESP_D0", "ESP_D1", // PG + "ESP_D2", "ESP_D3", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", "", + "", "", "", ""; +}; diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi index 9e13c2aa8911..f909b1d4dbca 100644 --- a/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi +++ b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi @@ -416,6 +416,12 @@ uart0_pb_pins: uart0-pb-pins { function = "uart0"; }; + /omit-if-no-ref/ + uart1_pe_pins: uart1-pe-pins { + pins = "PE21", "PE22"; + function = "uart1"; + }; + uart2_pins: uart2-pins { pins = "PB0", "PB1"; function = "uart2";
NetCube Systems Kumquat is a board based on the Allwinner V3s SoC, including: - 64MB DDR2 included in SoC - 10/100 Mbps Ethernet - USB-C DRD - Audio Codec - Isolated CAN-FD - ESP32 over SDIO - 8MB SPI-NOR Flash for bootloader - I2C EEPROM for MAC addresses - SDIO Connector for eMMC or SD-Card - 8x 12/24V IOs, 4x normally open relays - DS3232 RTC - QWIIC connectors for external I2C devices Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li> --- arch/arm/boot/dts/allwinner/Makefile | 2 + .../allwinner/sun8i-v3s-netcube-kumquat.dts | 286 ++++++++++++++++++ arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi | 6 + 3 files changed, 294 insertions(+) create mode 100644 arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts