diff mbox series

[RFC,10/10] arm: dts: ti: Adds device tree nodes for PRU Cores, IEP and eCAP modules of PRU-ICSS2 Instance.

Message ID 20250110071351.66888-11-basharath@couthit.com (mailing list archive)
State New
Headers show
Series PRU-ICSSM Ethernet Driver | expand

Commit Message

Basharath Hussain Khaja Jan. 10, 2025, 7:13 a.m. UTC 
From: Roger Quadros <rogerq@ti.com>

The TI Sitara AM57xx series of devices consists of 2 PRU-ICSS instances
(PRU-ICSS1 and PRU-ICSS2). This patch adds the device tree nodes for the
PRU-ICSS2 instance to support DUAL-MAC mode of operation.

Each PRU-ICSS instance consists of two PRU cores along with various
peripherals such as the Interrupt Controller (PRU_INTC), the Industrial
Ethernet Peripheral(IEP), the Real Time Media Independent Interface
controller (MII_RT), and the Enhanced Capture (eCAP) event module.

am57-pruss.dtsi - Adds IEP and eCAP peripheral as child nodes of
the PRUSS subsystem node.

am57xx-idk-common.dtsi - Adds PRU-ICSS2 instance node along with
PRU eth port information and corresponding port configuration. It includes
interrupt mapping for packet reception, HW timestamp collection, and
PRU Ethernet ports in MII mode.

am571x-idk.dts, am572x-idk.dts and am574x-idk.dts - GPIO configuration
along with delay configuration for individual PRU Ethernet port.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Parvathi Pudi <parvathi@couthit.com>
Signed-off-by: Basharath Hussain Khaja <basharath@couthit.com>
---
 arch/arm/boot/dts/ti/omap/am57-pruss.dtsi     | 11 ++++
 arch/arm/boot/dts/ti/omap/am571x-idk.dts      |  8 ++-
 arch/arm/boot/dts/ti/omap/am572x-idk.dts      | 10 +--
 arch/arm/boot/dts/ti/omap/am574x-idk.dts      | 10 +--
 .../boot/dts/ti/omap/am57xx-idk-common.dtsi   | 63 +++++++++++++++++++
 5 files changed, 93 insertions(+), 9 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/ti/omap/am57-pruss.dtsi b/arch/arm/boot/dts/ti/omap/am57-pruss.dtsi
index 46c5383f0eee..f73316625608 100644
--- a/arch/arm/boot/dts/ti/omap/am57-pruss.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am57-pruss.dtsi
@@ -170,6 +170,17 @@  pruss2_iepclk_mux: iepclk-mux@30 {
 				};
 			};
 
+			pruss2_iep: iep@2e000 {
+				compatible = "ti,am5728-icss-iep";
+				reg = <0x2e000 0x31c>;
+				clocks = <&pruss2_iepclk_mux>;
+			};
+
+			pruss2_ecap: ecap@30000 {
+				compatible = "ti,pruss-ecap";
+				reg = <0x30000 0x60>;
+			};
+
 			pruss2_mii_rt: mii-rt@32000 {
 				compatible = "ti,pruss-mii", "syscon";
 				reg = <0x32000 0x58>;
diff --git a/arch/arm/boot/dts/ti/omap/am571x-idk.dts b/arch/arm/boot/dts/ti/omap/am571x-idk.dts
index 322cf79d22e9..02653b440585 100644
--- a/arch/arm/boot/dts/ti/omap/am571x-idk.dts
+++ b/arch/arm/boot/dts/ti/omap/am571x-idk.dts
@@ -214,5 +214,11 @@  &pruss1_mdio {
 };
 
 &pruss2_mdio {
-	status = "disabled";
+	reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	reset-delay-us = <2>;   /* PHY datasheet states 1uS min */
+};
+
+&pruss2_eth {
+	ti,pruss-gp-mux-sel = <4>,      /* MII2, needed for PRUSS1_MII0 */
+			      <4>;      /* MII2, needed for PRUSS1_MII1 */
 };
diff --git a/arch/arm/boot/dts/ti/omap/am572x-idk.dts b/arch/arm/boot/dts/ti/omap/am572x-idk.dts
index 94a738cb0a4d..54a8ccb9ca14 100644
--- a/arch/arm/boot/dts/ti/omap/am572x-idk.dts
+++ b/arch/arm/boot/dts/ti/omap/am572x-idk.dts
@@ -28,10 +28,12 @@  &mmc2 {
 	pinctrl-2 = <&mmc2_pins_ddr_rev20>;
 };
 
-&pruss1_mdio {
-	status = "disabled";
+&pruss2_eth0_phy {
+	reset-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+	reset-assert-us = <2>;   /* PHY datasheet states 1uS min */
 };
 
-&pruss2_mdio {
-	status = "disabled";
+&pruss2_eth1_phy {
+	reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	reset-assert-us = <2>;   /* PHY datasheet states 1uS min */
 };
diff --git a/arch/arm/boot/dts/ti/omap/am574x-idk.dts b/arch/arm/boot/dts/ti/omap/am574x-idk.dts
index 47b9174d2353..47b6c6cb210c 100644
--- a/arch/arm/boot/dts/ti/omap/am574x-idk.dts
+++ b/arch/arm/boot/dts/ti/omap/am574x-idk.dts
@@ -40,10 +40,12 @@  &emif1 {
 	status = "okay";
 };
 
-&pruss1_mdio {
-	status = "disabled";
+&pruss2_eth0_phy {
+	reset-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+	reset-assert-us = <2>;   /* PHY datasheet states 1uS min */
 };
 
-&pruss2_mdio {
-	status = "disabled";
+&pruss2_eth1_phy {
+	reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	reset-assert-us = <2>;   /* PHY datasheet states 1uS min */
 };
diff --git a/arch/arm/boot/dts/ti/omap/am57xx-idk-common.dtsi b/arch/arm/boot/dts/ti/omap/am57xx-idk-common.dtsi
index 43e3623f079c..da94984f47b8 100644
--- a/arch/arm/boot/dts/ti/omap/am57xx-idk-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/am57xx-idk-common.dtsi
@@ -155,6 +155,54 @@  src_clk_x1: src_clk_x1 {
 		compatible = "fixed-clock";
 		clock-frequency = <20000000>;
 	};
+
+	/* Dual-MAC Ethernet application node on PRU-ICSS2 */
+	pruss2_eth: pruss2-eth {
+		compatible = "ti,am57-prueth";
+		ti,prus = <&pru2_0>, <&pru2_1>;
+		sram = <&ocmcram1>;
+		ti,mii-rt = <&pruss2_mii_rt>;
+		ti,iep = <&pruss2_iep>;
+		ecap = <&pruss2_ecap>;
+		interrupts = <20 2 2>, <21 3 3>;
+		interrupt-names = "rx_lre_hp", "rx_lre_lp";
+		interrupt-parent = <&pruss2_intc>;
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pruss2_emac0: port@0 {
+				reg = <0>;
+				phy-handle = <&pruss2_eth0_phy>;
+				phy-mode = "mii";
+				interrupts = <20 2 2>, <26 6 6>, <23 6 6>;
+				interrupt-names = "rx", "emac_ptp_tx",
+								"hsr_ptp_tx";
+				ti,no-half-duplex;
+				/* Filled in by bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+			};
+
+			pruss2_emac1: port@1 {
+				reg = <1>;
+				phy-handle = <&pruss2_eth1_phy>;
+				phy-mode = "mii";
+				interrupts = <21 3 3>, <27 9 7>, <24 9 7>;
+				interrupt-names = "rx", "emac_ptp_tx",
+								"hsr_ptp_tx";
+				ti,no-half-duplex;
+				/* Filled in by bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+			};
+		};
+	};
+
+};
+
+&pruss2_iep {
+	interrupt-parent = <&pruss2_intc>;
+	interrupts = <7 7 8>;
+	interrupt-names = "iep_cap_cmp";
 };
 
 &dra7_pmx_core {
@@ -606,3 +654,18 @@  dpi_out: endpoint {
 		};
 	};
 };
+
+&pruss2_mdio {
+	status = "okay";
+	pruss2_eth0_phy: ethernet-phy@0 {
+		reg = <0>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	pruss2_eth1_phy: ethernet-phy@1 {
+		reg = <1>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+	};
+};