new file mode 100644
@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/atmel,at91sam9g45-dma.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Atmel Direct Memory Access Controller (DMA)
+
+maintainers:
+ - Ludovic Desroches <ludovic.desroches@microchip.com>
+
+description:
+ The Atmel Direct Memory Access Controller (DMAC) transfers data from a source
+ peripheral to a destination peripheral over one or more AMBA buses. One channel
+ is required for each source/destination pair. In the most basic configuration,
+ the DMAC has one master interface and one channel. The master interface reads
+ the data from a source and writes it to a destination. Two AMBA transfers are
+ required for each DMAC data transfer. This is also known as a dual-access transfer.
+ The DMAC is programmed via the APB interface.
+
+properties:
+ compatible:
+ enum:
+ - atmel,at91sam9g45-dma
+ - atmel,at91sam9rl-dma
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ "#dma-cells":
+ description:
+ Must be <2>, used to represent the number of integer cells in the dma
+ property of client devices. The two cells in order are
+ 1. The first cell represents the channel number.
+ 2. The second cell is 0 for RX and 1 for TX transfers.
+ const: 2
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ const: dma_clk
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - "#dma-cells"
+ - clocks
+ - clock-names
+
+additionalProperties: false
+
+examples:
+ - |
+ dma-controller@ffffec00 {
+ compatible = "atmel,at91sam9g45-dma";
+ reg = <0xffffec00 0x200>;
+ interrupts = <21>;
+ #dma-cells = <2>;
+ clocks = <&pmc 2 20>;
+ clock-names = "dma_clk";
+ };
+
+...
deleted file mode 100644
@@ -1,42 +0,0 @@
-* Atmel Direct Memory Access Controller (DMA)
-
-Required properties:
-- compatible: Should be "atmel,<chip>-dma".
-- reg: Should contain DMA registers location and length.
-- interrupts: Should contain DMA interrupt.
-- #dma-cells: Must be <2>, used to represent the number of integer cells in
-the dmas property of client devices.
-
-Example:
-
-dma0: dma@ffffec00 {
- compatible = "atmel,at91sam9g45-dma";
- reg = <0xffffec00 0x200>;
- interrupts = <21>;
- #dma-cells = <2>;
-};
-
-DMA clients connected to the Atmel DMA controller must use the format
-described in the dma.txt file, using a three-cell specifier for each channel:
-a phandle plus two integer cells.
-The three cells in order are:
-
-1. A phandle pointing to the DMA controller.
-2. The memory interface (16 most significant bits), the peripheral interface
-(16 less significant bits).
-3. Parameters for the at91 DMA configuration register which are device
-dependent:
- - bit 7-0: peripheral identifier for the hardware handshaking interface. The
- identifier can be different for tx and rx.
- - bit 11-8: FIFO configuration. 0 for half FIFO, 1 for ALAP, 2 for ASAP.
-
-Example:
-
-i2c0@i2c@f8010000 {
- compatible = "atmel,at91sam9x5-i2c";
- reg = <0xf8010000 0x100>;
- interrupts = <9 4 6>;
- dmas = <&dma0 1 7>,
- <&dma0 1 8>;
- dma-names = "tx", "rx";
-};
@@ -14,7 +14,7 @@ Required properties:
Required properties for devices compatible with "atmel,at91sam9g45-ssc":
- dmas: DMA specifier, consisting of a phandle to DMA controller node,
the memory interface and SSC DMA channel ID (for tx and rx).
- See Documentation/devicetree/bindings/dma/atmel-dma.txt for details.
+ See Documentation/devicetree/bindings/dma/atmel,at91sam9g45-dma.yaml for details.
- dma-names: Must be "tx", "rx".
Optional properties:
@@ -15348,7 +15348,7 @@ M: Ludovic Desroches <ludovic.desroches@microchip.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
L: dmaengine@vger.kernel.org
S: Supported
-F: Documentation/devicetree/bindings/dma/atmel-dma.txt
+F: Documentation/devicetree/bindings/dma/atmel,at91sam9g45-dma.yaml
F: drivers/dma/at_hdmac.c
F: drivers/dma/at_xdmac.c
F: include/dt-bindings/dma/at91.h