Message ID | 503A856A.9020303@yahoo.es (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
Hi Hein, Le 08/26/2012 10:22 PM, Hein Tibosch a écrit : > Earlier, atmel-mci was adapter to make use of the peripheral DMA > controller (PDC), in case normal DMA wouldn't work. > ( http://comments.gmane.org/gmane.linux.kernel.mmc/9403 ) > This works OK on ARM platforms (AT91), but it broke the driver > for AVR32, the AP700x. > This patch makes the use of PDC depend on CONFIG_AVR32 I think you should explain explicitly that even if the MCI has PDC support, the connection is not done for AVR chips. Otherwise you can add Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Thanks for the patch. Regards Ludovic > > Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es> > > --- > drivers/mmc/host/atmel-mci-regs.h | 7 +++++++ > drivers/mmc/host/atmel-mci.c | 2 +- > 2 files changed, 8 insertions(+), 1 deletions(-) > > diff --git a/drivers/mmc/host/atmel-mci-regs.h b/drivers/mmc/host/atmel-mci-regs.h > index ab56f7d..c97001e 100644 > --- a/drivers/mmc/host/atmel-mci-regs.h > +++ b/drivers/mmc/host/atmel-mci-regs.h > @@ -140,6 +140,13 @@ > #define atmci_writel(port,reg,value) \ > __raw_writel((value), (port)->regs + reg) > > +/* On AVR chips the Peripheral DMA Controller is not connected to MCI. */ > +#ifdef CONFIG_AVR32 > +# define ATMCI_PDC_CONNECTED 0 > +#else > +# define ATMCI_PDC_CONNECTED 1 > +#endif > + > /* > * Fix sconfig's burst size according to atmel MCI. We need to convert them as: > * 1 -> 0, 4 -> 1, 8 -> 2, 16 -> 3. > diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c > index 66e9fdc..702ab5c 100644 > --- a/drivers/mmc/host/atmel-mci.c > +++ b/drivers/mmc/host/atmel-mci.c > @@ -2205,7 +2205,7 @@ static void __init atmci_get_cap(struct atmel_mci *host) > "version: 0x%x\n", version); > > host->caps.has_dma_conf_reg = 0; > - host->caps.has_pdc = 1; > + host->caps.has_pdc = ATMCI_PDC_CONNECTED; > host->caps.has_cfg_reg = 0; > host->caps.has_cstor_reg = 0; > host->caps.has_highspeed = 0; >
diff --git a/drivers/mmc/host/atmel-mci-regs.h b/drivers/mmc/host/atmel-mci-regs.h index ab56f7d..c97001e 100644 --- a/drivers/mmc/host/atmel-mci-regs.h +++ b/drivers/mmc/host/atmel-mci-regs.h @@ -140,6 +140,13 @@ #define atmci_writel(port,reg,value) \ __raw_writel((value), (port)->regs + reg) +/* On AVR chips the Peripheral DMA Controller is not connected to MCI. */ +#ifdef CONFIG_AVR32 +# define ATMCI_PDC_CONNECTED 0 +#else +# define ATMCI_PDC_CONNECTED 1 +#endif + /* * Fix sconfig's burst size according to atmel MCI. We need to convert them as: * 1 -> 0, 4 -> 1, 8 -> 2, 16 -> 3. diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c index 66e9fdc..702ab5c 100644 --- a/drivers/mmc/host/atmel-mci.c +++ b/drivers/mmc/host/atmel-mci.c @@ -2205,7 +2205,7 @@ static void __init atmci_get_cap(struct atmel_mci *host) "version: 0x%x\n", version); host->caps.has_dma_conf_reg = 0; - host->caps.has_pdc = 1; + host->caps.has_pdc = ATMCI_PDC_CONNECTED; host->caps.has_cfg_reg = 0; host->caps.has_cstor_reg = 0; host->caps.has_highspeed = 0;
Earlier, atmel-mci was adapter to make use of the peripheral DMA controller (PDC), in case normal DMA wouldn't work. ( http://comments.gmane.org/gmane.linux.kernel.mmc/9403 ) This works OK on ARM platforms (AT91), but it broke the driver for AVR32, the AP700x. This patch makes the use of PDC depend on CONFIG_AVR32 Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es> --- drivers/mmc/host/atmel-mci-regs.h | 7 +++++++ drivers/mmc/host/atmel-mci.c | 2 +- 2 files changed, 8 insertions(+), 1 deletions(-)