| Message ID | 54eda40e56e8ea02ed9c5332ca6d3fb90d617cc7.1349778821.git.vipin.kumar@st.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 16:14 Tue 09 Oct , Vipin Kumar wrote: > Add support to accept nand timing parameters via device tree > > Signed-off-by: Vipin Kumar <vipin.kumar@st.com> > --- > .../devicetree/bindings/mtd/fsmc-nand.txt | 20 ++++++++ > drivers/mtd/nand/fsmc_nand.c | 59 ++++++++++++++-------- > include/linux/mtd/fsmc.h | 2 +- > 3 files changed, 59 insertions(+), 22 deletions(-) > > diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt > index 29d1a2f..6a7fc43 100644 > --- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt > +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt > @@ -13,6 +13,18 @@ Optional properties: > defaults to 1 byte > - nand-skip-bbtscan: Indicates the the BBT scanning should be skipped > > +- nand-timings-enabled: Indicates if the timing parameters are passed > + via DT > +- nand-timings,tclr: > +- nand-timings,tar: > +- nand-timings,thiz: > +- nand-timings,thold: > +- nand-timings,twait: > +- nand-timings,tset: All these timing parameters come from the actual > + nand device specification. Each of this represents a number of time > + period of hclk ie a number 4 in thold with hclk = 166MHz means that > + thold = (1000 / 166) * 4 ns = 24.09ns > + > Example: > > fsmc: flash@d1800000 { > @@ -26,6 +38,14 @@ Example: > st,cle-off = <0x10000>; > maxbanks = <1>; > > + nand-timings-enabled; > + nand-timings,tclr = <1>; > + nand-timings,tar = <1>; > + nand-timings,thiz = <1>; > + nand-timings,thold = <4>; > + nand-timings,twait = <6>; > + nand-timings,tset = <0>; > + > bank-width = <1>; > nand-skip-bbtscan; > > diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c > index fc6a044..f3d69b3 100644 > --- a/drivers/mtd/nand/fsmc_nand.c > +++ b/drivers/mtd/nand/fsmc_nand.c > @@ -415,27 +415,13 @@ static void fsmc_nand_setup(void __iomem *regs, uint32_t bank, > { > uint32_t value = FSMC_DEVTYPE_NAND | FSMC_ENABLE | FSMC_WAITON; > uint32_t tclr, tar, thiz, thold, twait, tset; > - struct fsmc_nand_timings *tims; > - struct fsmc_nand_timings default_timings = { > - .tclr = FSMC_TCLR_1, > - .tar = FSMC_TAR_1, > - .thiz = FSMC_THIZ_1, > - .thold = FSMC_THOLD_4, > - .twait = FSMC_TWAIT_6, > - .tset = FSMC_TSET_0, > - }; > - > - if (timings) > - tims = timings; > - else > - tims = &default_timings; > > - tclr = (tims->tclr & FSMC_TCLR_MASK) << FSMC_TCLR_SHIFT; > - tar = (tims->tar & FSMC_TAR_MASK) << FSMC_TAR_SHIFT; > - thiz = (tims->thiz & FSMC_THIZ_MASK) << FSMC_THIZ_SHIFT; > - thold = (tims->thold & FSMC_THOLD_MASK) << FSMC_THOLD_SHIFT; > - twait = (tims->twait & FSMC_TWAIT_MASK) << FSMC_TWAIT_SHIFT; > - tset = (tims->tset & FSMC_TSET_MASK) << FSMC_TSET_SHIFT; > + tclr = (timings->tclr & FSMC_TCLR_MASK) << FSMC_TCLR_SHIFT; > + tar = (timings->tar & FSMC_TAR_MASK) << FSMC_TAR_SHIFT; > + thiz = (timings->thiz & FSMC_THIZ_MASK) << FSMC_THIZ_SHIFT; > + thold = (timings->thold & FSMC_THOLD_MASK) << FSMC_THOLD_SHIFT; > + twait = (timings->twait & FSMC_TWAIT_MASK) << FSMC_TWAIT_SHIFT; > + tset = (timings->tset & FSMC_TSET_MASK) << FSMC_TSET_SHIFT; > > if (busw) > writel(value | FSMC_DEVWID_16, FSMC_NAND_REG(regs, bank, PC)); > @@ -876,6 +862,14 @@ static int __devinit fsmc_nand_probe_config_dt(struct platform_device *pdev, > struct device_node *np) > { > struct fsmc_nand_platform_data *pdata = dev_get_platdata(&pdev->dev); > + struct fsmc_nand_timings default_timings = { > + .tclr = FSMC_TCLR_1, > + .tar = FSMC_TAR_1, > + .thiz = FSMC_THIZ_1, > + .thold = FSMC_THOLD_4, > + .twait = FSMC_TWAIT_6, > + .tset = FSMC_TSET_0, > + }; > u32 val; > > /* Set default NAND width to 8 bits */ > @@ -894,6 +888,29 @@ static int __devinit fsmc_nand_probe_config_dt(struct platform_device *pdev, > pdata->options = NAND_SKIP_BBTSCAN; > of_property_read_u32(np, "maxbanks", &pdata->max_banks); > > + if (of_property_read_bool(np, "nand-timings-enabled")) { > + of_property_read_u32(np, "nand-timings,tclr", &val); > + pdata->nand_timings.tclr = (uint8_t)val; use a mask will be better > + > + of_property_read_u32(np, "nand-timings,tar", &val); > + pdata->nand_timings.tar = (uint8_t)val; > + > + of_property_read_u32(np, "nand-timings,thiz", &val); > + pdata->nand_timings.thiz = (uint8_t)val; > + > + of_property_read_u32(np, "nand-timings,thold", &val); > + pdata->nand_timings.thold = (uint8_t)val; > + > + of_property_read_u32(np, "nand-timings,twait", &val); > + pdata->nand_timings.twait = (uint8_t)val; > + > + of_property_read_u32(np, "nand-timings,tset", &val); > + pdata->nand_timings.tset = (uint8_t)val; > + } else { > + memcpy(&pdata->nand_timings, &default_timings, > + sizeof(default_timings)); > + } > + > return 0; > } > #else > @@ -1031,7 +1048,7 @@ static int __init fsmc_nand_probe(struct platform_device *pdev) > host->partitions = pdata->partitions; > host->nr_partitions = pdata->nr_partitions; > host->dev = &pdev->dev; > - host->dev_timings = pdata->nand_timings; > + host->dev_timings = &pdata->nand_timings; > host->mode = pdata->mode; > host->max_banks = pdata->max_banks; > > diff --git a/include/linux/mtd/fsmc.h b/include/linux/mtd/fsmc.h > index f0ab734..4fbdce4 100644 > --- a/include/linux/mtd/fsmc.h > +++ b/include/linux/mtd/fsmc.h > @@ -148,7 +148,7 @@ enum access_mode { > * this may be set to NULL > */ > struct fsmc_nand_platform_data { > - struct fsmc_nand_timings *nand_timings; > + struct fsmc_nand_timings nand_timings; > struct mtd_partition *partitions; > unsigned int nr_partitions; > unsigned int options; > -- > 1.7.11.4 >
On Tue, Oct 9, 2012 at 4:14 PM, Vipin Kumar <vipin.kumar@st.com> wrote: > diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt > +- nand-timings-enabled: Indicates if the timing parameters are passed > + via DT > +- nand-timings,tclr: > +- nand-timings,tar: > +- nand-timings,thiz: > +- nand-timings,thold: > +- nand-timings,twait: > +- nand-timings,tset: All these timing parameters come from the actual > + nand device specification. Each of this represents a number of time > + period of hclk ie a number 4 in thold with hclk = 166MHz means that > + thold = (1000 / 166) * 4 ns = 24.09ns Are they specific to fsmc controller or nand memory type? If to fsmc then please add my Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org> else I would suggest to add these to mtd bindings instead, so that same fields can be used by multiple drivers.... Similar approach is used for mmc controllers too.
On 10/9/2012 5:27 PM, Jean-Christophe PLAGNIOL-VILLARD wrote: > On 16:14 Tue 09 Oct , Vipin Kumar wrote: >> Add support to accept nand timing parameters via device tree >> >> Signed-off-by: Vipin Kumar<vipin.kumar@st.com> >> --- >> .../devicetree/bindings/mtd/fsmc-nand.txt | 20 ++++++++ >> drivers/mtd/nand/fsmc_nand.c | 59 ++++++++++++++-------- >> include/linux/mtd/fsmc.h | 2 +- >> 3 files changed, 59 insertions(+), 22 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt >> index 29d1a2f..6a7fc43 100644 >> --- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt >> +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt >> @@ -13,6 +13,18 @@ Optional properties: >> defaults to 1 byte >> - nand-skip-bbtscan: Indicates the the BBT scanning should be skipped >> >> +- nand-timings-enabled: Indicates if the timing parameters are passed >> + via DT >> +- nand-timings,tclr: >> +- nand-timings,tar: >> +- nand-timings,thiz: >> +- nand-timings,thold: >> +- nand-timings,twait: >> +- nand-timings,tset: All these timing parameters come from the actual >> + nand device specification. Each of this represents a number of time >> + period of hclk ie a number 4 in thold with hclk = 166MHz means that >> + thold = (1000 / 166) * 4 ns = 24.09ns >> + >> Example: >> >> fsmc: flash@d1800000 { >> @@ -26,6 +38,14 @@ Example: >> st,cle-off =<0x10000>; >> maxbanks =<1>; >> >> + nand-timings-enabled; >> + nand-timings,tclr =<1>; >> + nand-timings,tar =<1>; >> + nand-timings,thiz =<1>; >> + nand-timings,thold =<4>; >> + nand-timings,twait =<6>; >> + nand-timings,tset =<0>; >> + >> bank-width =<1>; >> nand-skip-bbtscan; >> >> diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c >> index fc6a044..f3d69b3 100644 >> --- a/drivers/mtd/nand/fsmc_nand.c >> +++ b/drivers/mtd/nand/fsmc_nand.c >> @@ -415,27 +415,13 @@ static void fsmc_nand_setup(void __iomem *regs, uint32_t bank, >> { >> uint32_t value = FSMC_DEVTYPE_NAND | FSMC_ENABLE | FSMC_WAITON; >> uint32_t tclr, tar, thiz, thold, twait, tset; >> - struct fsmc_nand_timings *tims; >> - struct fsmc_nand_timings default_timings = { >> - .tclr = FSMC_TCLR_1, >> - .tar = FSMC_TAR_1, >> - .thiz = FSMC_THIZ_1, >> - .thold = FSMC_THOLD_4, >> - .twait = FSMC_TWAIT_6, >> - .tset = FSMC_TSET_0, >> - }; >> - >> - if (timings) >> - tims = timings; >> - else >> - tims =&default_timings; >> >> - tclr = (tims->tclr& FSMC_TCLR_MASK)<< FSMC_TCLR_SHIFT; >> - tar = (tims->tar& FSMC_TAR_MASK)<< FSMC_TAR_SHIFT; >> - thiz = (tims->thiz& FSMC_THIZ_MASK)<< FSMC_THIZ_SHIFT; >> - thold = (tims->thold& FSMC_THOLD_MASK)<< FSMC_THOLD_SHIFT; >> - twait = (tims->twait& FSMC_TWAIT_MASK)<< FSMC_TWAIT_SHIFT; >> - tset = (tims->tset& FSMC_TSET_MASK)<< FSMC_TSET_SHIFT; >> + tclr = (timings->tclr& FSMC_TCLR_MASK)<< FSMC_TCLR_SHIFT; >> + tar = (timings->tar& FSMC_TAR_MASK)<< FSMC_TAR_SHIFT; >> + thiz = (timings->thiz& FSMC_THIZ_MASK)<< FSMC_THIZ_SHIFT; >> + thold = (timings->thold& FSMC_THOLD_MASK)<< FSMC_THOLD_SHIFT; >> + twait = (timings->twait& FSMC_TWAIT_MASK)<< FSMC_TWAIT_SHIFT; >> + tset = (timings->tset& FSMC_TSET_MASK)<< FSMC_TSET_SHIFT; >> >> if (busw) >> writel(value | FSMC_DEVWID_16, FSMC_NAND_REG(regs, bank, PC)); >> @@ -876,6 +862,14 @@ static int __devinit fsmc_nand_probe_config_dt(struct platform_device *pdev, >> struct device_node *np) >> { >> struct fsmc_nand_platform_data *pdata = dev_get_platdata(&pdev->dev); >> + struct fsmc_nand_timings default_timings = { >> + .tclr = FSMC_TCLR_1, >> + .tar = FSMC_TAR_1, >> + .thiz = FSMC_THIZ_1, >> + .thold = FSMC_THOLD_4, >> + .twait = FSMC_TWAIT_6, >> + .tset = FSMC_TSET_0, >> + }; >> u32 val; >> >> /* Set default NAND width to 8 bits */ >> @@ -894,6 +888,29 @@ static int __devinit fsmc_nand_probe_config_dt(struct platform_device *pdev, >> pdata->options = NAND_SKIP_BBTSCAN; >> of_property_read_u32(np, "maxbanks",&pdata->max_banks); >> >> + if (of_property_read_bool(np, "nand-timings-enabled")) { >> + of_property_read_u32(np, "nand-timings,tclr",&val); >> + pdata->nand_timings.tclr = (uint8_t)val; > use a mask will be better OK, will add a mask in v2 >> + >> + of_property_read_u32(np, "nand-timings,tar",&val); >> + pdata->nand_timings.tar = (uint8_t)val; >> + >> + of_property_read_u32(np, "nand-timings,thiz",&val); >> + pdata->nand_timings.thiz = (uint8_t)val; >> + >> + of_property_read_u32(np, "nand-timings,thold",&val); >> + pdata->nand_timings.thold = (uint8_t)val; >> + >> + of_property_read_u32(np, "nand-timings,twait",&val); >> + pdata->nand_timings.twait = (uint8_t)val; >> + >> + of_property_read_u32(np, "nand-timings,tset",&val); >> + pdata->nand_timings.tset = (uint8_t)val; >> + } else { >> + memcpy(&pdata->nand_timings,&default_timings, >> + sizeof(default_timings)); >> + } >> + >> return 0; >> } >> #else >> @@ -1031,7 +1048,7 @@ static int __init fsmc_nand_probe(struct platform_device *pdev) >> host->partitions = pdata->partitions; >> host->nr_partitions = pdata->nr_partitions; >> host->dev =&pdev->dev; >> - host->dev_timings = pdata->nand_timings; >> + host->dev_timings =&pdata->nand_timings; >> host->mode = pdata->mode; >> host->max_banks = pdata->max_banks; >> >> diff --git a/include/linux/mtd/fsmc.h b/include/linux/mtd/fsmc.h >> index f0ab734..4fbdce4 100644 >> --- a/include/linux/mtd/fsmc.h >> +++ b/include/linux/mtd/fsmc.h >> @@ -148,7 +148,7 @@ enum access_mode { >> * this may be set to NULL >> */ >> struct fsmc_nand_platform_data { >> - struct fsmc_nand_timings *nand_timings; >> + struct fsmc_nand_timings nand_timings; >> struct mtd_partition *partitions; >> unsigned int nr_partitions; >> unsigned int options; >> -- >> 1.7.11.4 >> > . >
diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt index 29d1a2f..6a7fc43 100644 --- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -13,6 +13,18 @@ Optional properties: defaults to 1 byte - nand-skip-bbtscan: Indicates the the BBT scanning should be skipped +- nand-timings-enabled: Indicates if the timing parameters are passed + via DT +- nand-timings,tclr: +- nand-timings,tar: +- nand-timings,thiz: +- nand-timings,thold: +- nand-timings,twait: +- nand-timings,tset: All these timing parameters come from the actual + nand device specification. Each of this represents a number of time + period of hclk ie a number 4 in thold with hclk = 166MHz means that + thold = (1000 / 166) * 4 ns = 24.09ns + Example: fsmc: flash@d1800000 { @@ -26,6 +38,14 @@ Example: st,cle-off = <0x10000>; maxbanks = <1>; + nand-timings-enabled; + nand-timings,tclr = <1>; + nand-timings,tar = <1>; + nand-timings,thiz = <1>; + nand-timings,thold = <4>; + nand-timings,twait = <6>; + nand-timings,tset = <0>; + bank-width = <1>; nand-skip-bbtscan; diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c index fc6a044..f3d69b3 100644 --- a/drivers/mtd/nand/fsmc_nand.c +++ b/drivers/mtd/nand/fsmc_nand.c @@ -415,27 +415,13 @@ static void fsmc_nand_setup(void __iomem *regs, uint32_t bank, { uint32_t value = FSMC_DEVTYPE_NAND | FSMC_ENABLE | FSMC_WAITON; uint32_t tclr, tar, thiz, thold, twait, tset; - struct fsmc_nand_timings *tims; - struct fsmc_nand_timings default_timings = { - .tclr = FSMC_TCLR_1, - .tar = FSMC_TAR_1, - .thiz = FSMC_THIZ_1, - .thold = FSMC_THOLD_4, - .twait = FSMC_TWAIT_6, - .tset = FSMC_TSET_0, - }; - - if (timings) - tims = timings; - else - tims = &default_timings; - tclr = (tims->tclr & FSMC_TCLR_MASK) << FSMC_TCLR_SHIFT; - tar = (tims->tar & FSMC_TAR_MASK) << FSMC_TAR_SHIFT; - thiz = (tims->thiz & FSMC_THIZ_MASK) << FSMC_THIZ_SHIFT; - thold = (tims->thold & FSMC_THOLD_MASK) << FSMC_THOLD_SHIFT; - twait = (tims->twait & FSMC_TWAIT_MASK) << FSMC_TWAIT_SHIFT; - tset = (tims->tset & FSMC_TSET_MASK) << FSMC_TSET_SHIFT; + tclr = (timings->tclr & FSMC_TCLR_MASK) << FSMC_TCLR_SHIFT; + tar = (timings->tar & FSMC_TAR_MASK) << FSMC_TAR_SHIFT; + thiz = (timings->thiz & FSMC_THIZ_MASK) << FSMC_THIZ_SHIFT; + thold = (timings->thold & FSMC_THOLD_MASK) << FSMC_THOLD_SHIFT; + twait = (timings->twait & FSMC_TWAIT_MASK) << FSMC_TWAIT_SHIFT; + tset = (timings->tset & FSMC_TSET_MASK) << FSMC_TSET_SHIFT; if (busw) writel(value | FSMC_DEVWID_16, FSMC_NAND_REG(regs, bank, PC)); @@ -876,6 +862,14 @@ static int __devinit fsmc_nand_probe_config_dt(struct platform_device *pdev, struct device_node *np) { struct fsmc_nand_platform_data *pdata = dev_get_platdata(&pdev->dev); + struct fsmc_nand_timings default_timings = { + .tclr = FSMC_TCLR_1, + .tar = FSMC_TAR_1, + .thiz = FSMC_THIZ_1, + .thold = FSMC_THOLD_4, + .twait = FSMC_TWAIT_6, + .tset = FSMC_TSET_0, + }; u32 val; /* Set default NAND width to 8 bits */ @@ -894,6 +888,29 @@ static int __devinit fsmc_nand_probe_config_dt(struct platform_device *pdev, pdata->options = NAND_SKIP_BBTSCAN; of_property_read_u32(np, "maxbanks", &pdata->max_banks); + if (of_property_read_bool(np, "nand-timings-enabled")) { + of_property_read_u32(np, "nand-timings,tclr", &val); + pdata->nand_timings.tclr = (uint8_t)val; + + of_property_read_u32(np, "nand-timings,tar", &val); + pdata->nand_timings.tar = (uint8_t)val; + + of_property_read_u32(np, "nand-timings,thiz", &val); + pdata->nand_timings.thiz = (uint8_t)val; + + of_property_read_u32(np, "nand-timings,thold", &val); + pdata->nand_timings.thold = (uint8_t)val; + + of_property_read_u32(np, "nand-timings,twait", &val); + pdata->nand_timings.twait = (uint8_t)val; + + of_property_read_u32(np, "nand-timings,tset", &val); + pdata->nand_timings.tset = (uint8_t)val; + } else { + memcpy(&pdata->nand_timings, &default_timings, + sizeof(default_timings)); + } + return 0; } #else @@ -1031,7 +1048,7 @@ static int __init fsmc_nand_probe(struct platform_device *pdev) host->partitions = pdata->partitions; host->nr_partitions = pdata->nr_partitions; host->dev = &pdev->dev; - host->dev_timings = pdata->nand_timings; + host->dev_timings = &pdata->nand_timings; host->mode = pdata->mode; host->max_banks = pdata->max_banks; diff --git a/include/linux/mtd/fsmc.h b/include/linux/mtd/fsmc.h index f0ab734..4fbdce4 100644 --- a/include/linux/mtd/fsmc.h +++ b/include/linux/mtd/fsmc.h @@ -148,7 +148,7 @@ enum access_mode { * this may be set to NULL */ struct fsmc_nand_platform_data { - struct fsmc_nand_timings *nand_timings; + struct fsmc_nand_timings nand_timings; struct mtd_partition *partitions; unsigned int nr_partitions; unsigned int options;
Add support to accept nand timing parameters via device tree Signed-off-by: Vipin Kumar <vipin.kumar@st.com> --- .../devicetree/bindings/mtd/fsmc-nand.txt | 20 ++++++++ drivers/mtd/nand/fsmc_nand.c | 59 ++++++++++++++-------- include/linux/mtd/fsmc.h | 2 +- 3 files changed, 59 insertions(+), 22 deletions(-)