| Message ID | 60057bbf7d39ec63d391d26271747cf0228a3ed1.1437669004.git.cyrille.pitchen@atmel.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Thu, 23 Jul 2015 18:42:55 +0200 Cyrille Pitchen <cyrille.pitchen@atmel.com> wrote: > This patch documents the DT bindings for the Atmel Flexcom which will be > introduced by sama5d2x SoCs. These bindings will be used by the actual > Flexcom driver to be sent in another patch. > > Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> > --- > .../devicetree/bindings/mfd/atmel-flexcom.txt | 68 ++++++++++++++++++++++ > 1 file changed, 68 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt > > diff --git a/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt > new file mode 100644 > index 000000000000..a63226b7a9cb > --- /dev/null > +++ b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt > @@ -0,0 +1,68 @@ > +* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit) > + > +The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C > +controller and an USART. Only one function can be used at a time and is chosen > +at boot time according to the device tree. > + > +Required properties: > +- compatible: Should be "atmel,sama5d2-flexcom" > +- reg: Should be the pair (offset, size) for the Flexcom > + dedicated I/O registers (without USART, TWI or SPI > + registers). > +- clocks: Should be the Flexcom peripheral clock from PMC. > +- #address-cells: Should be <2> > +- #size-cells: Should be <1> > +- ranges: Should be a list of ranges. > + One range per peripheral wrapped by the Flexcom. So each > + range is a triplet (child_addr, parent_addr, size). The > + first u32 of "child_addr" is the value to be set in the > + Operating Mode bitfield of the Flexcom Mode Register. > + Then "parent_addr" stores the base address of the > + corresponding peripheral in the system memory. Finally, > + "size" if the size of the memory region of this > + peripheral. > + > +Required child: > +A single available child for the serial controller to enable. > + > +Required properties of this child: > +- reg: Should be a pair (child_addr, size) with child_addr > + matching one of the parent ranges. > +- clocks: Should be the very same phandle as for the parent's one. > + > +Other properties remain unchanged. See documentation of the respective device: > +- ../serial/atmel-usart.txt > +- ../spi/spi_atmel.txt > +- ../i2c/i2c-at91.txt > + > +Example: > + > +flexcom@f8034000 { > + compatible = "atmel,sama5d2-flexcom"; > + reg = <0xf8034000 0x200>; > + clocks = <&flx0_clk>; > + #address-cells = <2>; > + #size-cells = <1>; > + ranges = <1 0 0xf8034200 0x200 /* opmode 1: USART */ > + 2 0 0xf8034400 0x200 /* opmode 2: SPI */ > + 3 0 0xf8034600 0x200>; /* opmode 3: I2C */ > + > + spi@f8034400 { Should be: spi@2,0 { > + compatible = "atmel,at91rm9200-spi"; > + reg = <2 0 0x200>; > + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_flx0_default>; > + #address-cells = <1>; > + #size-cells = <0>; > + clocks = <&flx0_clk>; > + clock-names = "spi_clk"; > + atmel,fifo-size = <32>; > + > + mtd_dataflash@0 { > + compatible = "atmel,at25f512b"; > + reg = <0>; > + spi-max-frequency = <20000000>; > + }; > + }; > +};
Le 23/07/2015 21:48, Boris Brezillon a écrit : > On Thu, 23 Jul 2015 18:42:55 +0200 > Cyrille Pitchen <cyrille.pitchen@atmel.com> wrote: > >> This patch documents the DT bindings for the Atmel Flexcom which will be >> introduced by sama5d2x SoCs. These bindings will be used by the actual >> Flexcom driver to be sent in another patch. >> >> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> >> --- >> .../devicetree/bindings/mfd/atmel-flexcom.txt | 68 ++++++++++++++++++++++ >> 1 file changed, 68 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt >> >> diff --git a/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt >> new file mode 100644 >> index 000000000000..a63226b7a9cb >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt >> @@ -0,0 +1,68 @@ >> +* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit) >> + >> +The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C >> +controller and an USART. Only one function can be used at a time and is chosen >> +at boot time according to the device tree. >> + >> +Required properties: >> +- compatible: Should be "atmel,sama5d2-flexcom" >> +- reg: Should be the pair (offset, size) for the Flexcom >> + dedicated I/O registers (without USART, TWI or SPI >> + registers). >> +- clocks: Should be the Flexcom peripheral clock from PMC. >> +- #address-cells: Should be <2> >> +- #size-cells: Should be <1> >> +- ranges: Should be a list of ranges. >> + One range per peripheral wrapped by the Flexcom. So each >> + range is a triplet (child_addr, parent_addr, size). The >> + first u32 of "child_addr" is the value to be set in the >> + Operating Mode bitfield of the Flexcom Mode Register. >> + Then "parent_addr" stores the base address of the >> + corresponding peripheral in the system memory. Finally, >> + "size" if the size of the memory region of this >> + peripheral. >> + >> +Required child: >> +A single available child for the serial controller to enable. >> + >> +Required properties of this child: >> +- reg: Should be a pair (child_addr, size) with child_addr >> + matching one of the parent ranges. >> +- clocks: Should be the very same phandle as for the parent's one. >> + >> +Other properties remain unchanged. See documentation of the respective device: >> +- ../serial/atmel-usart.txt >> +- ../spi/spi_atmel.txt >> +- ../i2c/i2c-at91.txt >> + >> +Example: >> + >> +flexcom@f8034000 { >> + compatible = "atmel,sama5d2-flexcom"; >> + reg = <0xf8034000 0x200>; >> + clocks = <&flx0_clk>; >> + #address-cells = <2>; >> + #size-cells = <1>; >> + ranges = <1 0 0xf8034200 0x200 /* opmode 1: USART */ >> + 2 0 0xf8034400 0x200 /* opmode 2: SPI */ >> + 3 0 0xf8034600 0x200>; /* opmode 3: I2C */ Yes, the opmode(s) are exactly the values described in the product datasheet. >> + >> + spi@f8034400 { > > Should be: > > spi@2,0 { Yep! I was silently following the discussion in the background and I admit that this approach is pretty elegant. So, if this approach is validated you can also add my: Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> >> + compatible = "atmel,at91rm9200-spi"; >> + reg = <2 0 0x200>; >> + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_flx0_default>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + clocks = <&flx0_clk>; >> + clock-names = "spi_clk"; >> + atmel,fifo-size = <32>; >> + >> + mtd_dataflash@0 { >> + compatible = "atmel,at25f512b"; >> + reg = <0>; >> + spi-max-frequency = <20000000>; >> + }; >> + }; >> +}; > > >
On Fri, 24 Jul 2015, Nicolas Ferre wrote: > Le 23/07/2015 21:48, Boris Brezillon a écrit : > > On Thu, 23 Jul 2015 18:42:55 +0200 > > Cyrille Pitchen <cyrille.pitchen@atmel.com> wrote: > > > >> This patch documents the DT bindings for the Atmel Flexcom which will be > >> introduced by sama5d2x SoCs. These bindings will be used by the actual > >> Flexcom driver to be sent in another patch. > >> > >> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> > >> --- > >> .../devicetree/bindings/mfd/atmel-flexcom.txt | 68 ++++++++++++++++++++++ > >> 1 file changed, 68 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt > >> > >> diff --git a/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt > >> new file mode 100644 > >> index 000000000000..a63226b7a9cb > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt > >> @@ -0,0 +1,68 @@ > >> +* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit) > >> + > >> +The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C > >> +controller and an USART. Only one function can be used at a time and is chosen > >> +at boot time according to the device tree. > >> + > >> +Required properties: > >> +- compatible: Should be "atmel,sama5d2-flexcom" > >> +- reg: Should be the pair (offset, size) for the Flexcom > >> + dedicated I/O registers (without USART, TWI or SPI > >> + registers). > >> +- clocks: Should be the Flexcom peripheral clock from PMC. > >> +- #address-cells: Should be <2> > >> +- #size-cells: Should be <1> > >> +- ranges: Should be a list of ranges. > >> + One range per peripheral wrapped by the Flexcom. So each > >> + range is a triplet (child_addr, parent_addr, size). The > >> + first u32 of "child_addr" is the value to be set in the > >> + Operating Mode bitfield of the Flexcom Mode Register. > >> + Then "parent_addr" stores the base address of the > >> + corresponding peripheral in the system memory. Finally, > >> + "size" if the size of the memory region of this > >> + peripheral. > >> + > >> +Required child: > >> +A single available child for the serial controller to enable. > >> + > >> +Required properties of this child: > >> +- reg: Should be a pair (child_addr, size) with child_addr > >> + matching one of the parent ranges. > >> +- clocks: Should be the very same phandle as for the parent's one. > >> + > >> +Other properties remain unchanged. See documentation of the respective device: > >> +- ../serial/atmel-usart.txt > >> +- ../spi/spi_atmel.txt > >> +- ../i2c/i2c-at91.txt > >> + > >> +Example: > >> + > >> +flexcom@f8034000 { > >> + compatible = "atmel,sama5d2-flexcom"; > >> + reg = <0xf8034000 0x200>; > >> + clocks = <&flx0_clk>; > >> + #address-cells = <2>; > >> + #size-cells = <1>; > >> + ranges = <1 0 0xf8034200 0x200 /* opmode 1: USART */ > >> + 2 0 0xf8034400 0x200 /* opmode 2: SPI */ > >> + 3 0 0xf8034600 0x200>; /* opmode 3: I2C */ > > Yes, the opmode(s) are exactly the values described in the product > datasheet. > > >> + > >> + spi@f8034400 { > > > > Should be: > > > > spi@2,0 { > > Yep! > > I was silently following the discussion in the background and I admit > that this approach is pretty elegant. > > So, if this approach is validated you can also add my: > Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Please see my reply to v6 for the usual way to achieve this. > >> + compatible = "atmel,at91rm9200-spi"; > >> + reg = <2 0 0x200>; > >> + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>; > >> + pinctrl-names = "default"; > >> + pinctrl-0 = <&pinctrl_flx0_default>; > >> + #address-cells = <1>; > >> + #size-cells = <0>; > >> + clocks = <&flx0_clk>; > >> + clock-names = "spi_clk"; > >> + atmel,fifo-size = <32>; > >> + > >> + mtd_dataflash@0 { > >> + compatible = "atmel,at25f512b"; > >> + reg = <0>; > >> + spi-max-frequency = <20000000>; > >> + }; > >> + }; > >> +}; > > > > > > > >
On Fri, 24 Jul 2015, Lee Jones wrote: > On Fri, 24 Jul 2015, Nicolas Ferre wrote: > > > Le 23/07/2015 21:48, Boris Brezillon a écrit : > > > On Thu, 23 Jul 2015 18:42:55 +0200 > > > Cyrille Pitchen <cyrille.pitchen@atmel.com> wrote: > > > > > >> This patch documents the DT bindings for the Atmel Flexcom which will be > > >> introduced by sama5d2x SoCs. These bindings will be used by the actual > > >> Flexcom driver to be sent in another patch. > > >> > > >> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> > > >> --- > > >> .../devicetree/bindings/mfd/atmel-flexcom.txt | 68 ++++++++++++++++++++++ > > >> 1 file changed, 68 insertions(+) > > >> create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt > > >> > > >> diff --git a/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt > > >> new file mode 100644 > > >> index 000000000000..a63226b7a9cb > > >> --- /dev/null > > >> +++ b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt > > >> @@ -0,0 +1,68 @@ > > >> +* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit) > > >> + > > >> +The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C > > >> +controller and an USART. Only one function can be used at a time and is chosen > > >> +at boot time according to the device tree. > > >> + > > >> +Required properties: > > >> +- compatible: Should be "atmel,sama5d2-flexcom" > > >> +- reg: Should be the pair (offset, size) for the Flexcom > > >> + dedicated I/O registers (without USART, TWI or SPI > > >> + registers). > > >> +- clocks: Should be the Flexcom peripheral clock from PMC. > > >> +- #address-cells: Should be <2> > > >> +- #size-cells: Should be <1> > > >> +- ranges: Should be a list of ranges. > > >> + One range per peripheral wrapped by the Flexcom. So each > > >> + range is a triplet (child_addr, parent_addr, size). The > > >> + first u32 of "child_addr" is the value to be set in the > > >> + Operating Mode bitfield of the Flexcom Mode Register. > > >> + Then "parent_addr" stores the base address of the > > >> + corresponding peripheral in the system memory. Finally, > > >> + "size" if the size of the memory region of this > > >> + peripheral. > > >> + > > >> +Required child: > > >> +A single available child for the serial controller to enable. > > >> + > > >> +Required properties of this child: > > >> +- reg: Should be a pair (child_addr, size) with child_addr > > >> + matching one of the parent ranges. > > >> +- clocks: Should be the very same phandle as for the parent's one. > > >> + > > >> +Other properties remain unchanged. See documentation of the respective device: > > >> +- ../serial/atmel-usart.txt > > >> +- ../spi/spi_atmel.txt > > >> +- ../i2c/i2c-at91.txt > > >> + > > >> +Example: > > >> + > > >> +flexcom@f8034000 { > > >> + compatible = "atmel,sama5d2-flexcom"; > > >> + reg = <0xf8034000 0x200>; > > >> + clocks = <&flx0_clk>; > > >> + #address-cells = <2>; > > >> + #size-cells = <1>; > > >> + ranges = <1 0 0xf8034200 0x200 /* opmode 1: USART */ > > >> + 2 0 0xf8034400 0x200 /* opmode 2: SPI */ > > >> + 3 0 0xf8034600 0x200>; /* opmode 3: I2C */ > > > > Yes, the opmode(s) are exactly the values described in the product > > datasheet. > > > > >> + > > >> + spi@f8034400 { > > > > > > Should be: > > > > > > spi@2,0 { > > > > Yep! > > > > I was silently following the discussion in the background and I admit > > that this approach is pretty elegant. > > > > So, if this approach is validated you can also add my: > > Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> > > Please see my reply to v6 for the usual way to achieve this. Ah, actually scrap that. Looks like I was thinking you were doing something different. Well I don't know enough about the advanced use of the ranges property to comment on this. I need to call for some assistance from the DT chaps. > > >> + compatible = "atmel,at91rm9200-spi"; > > >> + reg = <2 0 0x200>; > > >> + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>; > > >> + pinctrl-names = "default"; > > >> + pinctrl-0 = <&pinctrl_flx0_default>; > > >> + #address-cells = <1>; > > >> + #size-cells = <0>; > > >> + clocks = <&flx0_clk>; > > >> + clock-names = "spi_clk"; > > >> + atmel,fifo-size = <32>; > > >> + > > >> + mtd_dataflash@0 { > > >> + compatible = "atmel,at25f512b"; > > >> + reg = <0>; > > >> + spi-max-frequency = <20000000>; > > >> + }; > > >> + }; > > >> +}; > > > > > > > > > > > > > >
diff --git a/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt new file mode 100644 index 000000000000..a63226b7a9cb --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt @@ -0,0 +1,68 @@ +* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit) + +The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C +controller and an USART. Only one function can be used at a time and is chosen +at boot time according to the device tree. + +Required properties: +- compatible: Should be "atmel,sama5d2-flexcom" +- reg: Should be the pair (offset, size) for the Flexcom + dedicated I/O registers (without USART, TWI or SPI + registers). +- clocks: Should be the Flexcom peripheral clock from PMC. +- #address-cells: Should be <2> +- #size-cells: Should be <1> +- ranges: Should be a list of ranges. + One range per peripheral wrapped by the Flexcom. So each + range is a triplet (child_addr, parent_addr, size). The + first u32 of "child_addr" is the value to be set in the + Operating Mode bitfield of the Flexcom Mode Register. + Then "parent_addr" stores the base address of the + corresponding peripheral in the system memory. Finally, + "size" if the size of the memory region of this + peripheral. + +Required child: +A single available child for the serial controller to enable. + +Required properties of this child: +- reg: Should be a pair (child_addr, size) with child_addr + matching one of the parent ranges. +- clocks: Should be the very same phandle as for the parent's one. + +Other properties remain unchanged. See documentation of the respective device: +- ../serial/atmel-usart.txt +- ../spi/spi_atmel.txt +- ../i2c/i2c-at91.txt + +Example: + +flexcom@f8034000 { + compatible = "atmel,sama5d2-flexcom"; + reg = <0xf8034000 0x200>; + clocks = <&flx0_clk>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <1 0 0xf8034200 0x200 /* opmode 1: USART */ + 2 0 0xf8034400 0x200 /* opmode 2: SPI */ + 3 0 0xf8034600 0x200>; /* opmode 3: I2C */ + + spi@f8034400 { + compatible = "atmel,at91rm9200-spi"; + reg = <2 0 0x200>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flx0_default>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&flx0_clk>; + clock-names = "spi_clk"; + atmel,fifo-size = <32>; + + mtd_dataflash@0 { + compatible = "atmel,at25f512b"; + reg = <0>; + spi-max-frequency = <20000000>; + }; + }; +};
This patch documents the DT bindings for the Atmel Flexcom which will be introduced by sama5d2x SoCs. These bindings will be used by the actual Flexcom driver to be sent in another patch. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> --- .../devicetree/bindings/mfd/atmel-flexcom.txt | 68 ++++++++++++++++++++++ 1 file changed, 68 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt