@@ -107,6 +107,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6b-io.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-evb1-v10.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-jaguar.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-nanopc-t6.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-ok3588-c.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-orangepi-5-plus.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-quartzpro64.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-rock-5b.dtb
new file mode 100644
@@ -0,0 +1,390 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+#include "rk3588-forlinx-fet3588-c.dtsi"
+
+/ {
+ model = "Forlinx OK3588-C Board";
+ compatible = "forlinx,ok3588-c", "forlinx,fet3588-c", "rockchip,rk3588";
+
+ aliases {
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ mmc1 = &sdmmc;
+ };
+
+ adc-keys-0 {
+ compatible = "adc-keys";
+ io-channels = <&saradc 0>;
+ io-channel-names = "buttons";
+ keyup-threshold-microvolt = <1800000>;
+ poll-interval = <100>;
+
+ button-maskrom {
+ label = "Maskrom";
+ linux,code = <KEY_SETUP>;
+ press-threshold-microvolt = <400>;
+ };
+ };
+
+ adc-keys-1 {
+ compatible = "adc-keys";
+ io-channels = <&saradc 1>;
+ io-channel-names = "buttons";
+ keyup-threshold-microvolt = <1800000>;
+ poll-interval = <100>;
+
+ button-volume-up {
+ label = "V+/Recovery";
+ linux,code = <KEY_VOLUMEUP>;
+ press-threshold-microvolt = <17000>;
+ };
+
+ button-volume-down {
+ label = "V-";
+ linux,code = <KEY_VOLUMEDOWN>;
+ press-threshold-microvolt = <417000>;
+ };
+
+ button-menu {
+ label = "Menu";
+ linux,code = <KEY_MENU>;
+ press-threshold-microvolt = <890000>;
+ };
+
+ button-escape {
+ label = "ESC";
+ linux,code = <KEY_ESC>;
+ press-threshold-microvolt = <1235000>;
+ };
+ };
+
+ analog-sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_detect>;
+ simple-audio-card,name = "RK3588 OK3588-C Audio";
+ simple-audio-card,bitclock-master = <&masterdai>;
+ simple-audio-card,format = "i2s";
+ simple-audio-card,frame-master = <&masterdai>;
+ simple-audio-card,hp-det-gpio = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
+ simple-audio-card,mclk-fs = <256>;
+ simple-audio-card,pin-switches = "Headphones", "Speaker";
+ simple-audio-card,widgets =
+ "Headphones", "Headphones",
+ "Speaker", "Speaker",
+ "Microphone", "Internal Microphone",
+ "Microphone", "Headset Microphone";
+ simple-audio-card,routing =
+ "Headphones", "LHP",
+ "Headphones", "RHP",
+ "Speaker", "LSPK",
+ "Speaker", "RSPK",
+ "LMICP", "Headset Microphone",
+ "RMICP", "Internal Microphone";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s0_8ch>;
+ };
+
+ masterdai: simple-audio-card,codec {
+ sound-dai = <&nau8822>;
+ };
+ };
+
+ fan: pwm-fan {
+ compatible = "pwm-fan";
+ cooling-levels = <0 95 145 195 255>;
+ fan-supply = <&vcc12v_dcin>;
+ pwms = <&pwm2 0 50000 0>;
+ #cooling-cells = <2>;
+ };
+
+ vcc12v_dcin: vcc12v-dcin-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc1v8_sys: vcc1v8-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v8_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ vcc3v3_sys: vcc3v3-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc3v3_pcie2x1l0: vcc3v3-pcie2x1l0-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie2x1l0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <50000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc3v3_pcie2x1l2: vcc3v3-pcie2x1l2-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie2x1l2";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <5000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc3v3_pcie30: vcc3v3_pcie30-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie30";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+};
+
+&gmac0 {
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy0>;
+ phy-mode = "rgmii-rxid";
+ pinctrl-0 = <&gmac0_miim
+ &gmac0_tx_bus2
+ &gmac0_rx_bus2
+ &gmac0_rgmii_clk
+ &gmac0_rgmii_bus>;
+ pinctrl-names = "default";
+ tx_delay = <0x44>;
+ rx_delay = <0x00>;
+ status = "okay";
+};
+
+&gmac1 {
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy1>;
+ phy-mode = "rgmii-rxid";
+ pinctrl-0 = <&gmac1_miim
+ &gmac1_tx_bus2
+ &gmac1_rx_bus2
+ &gmac1_rgmii_clk
+ &gmac1_rgmii_bus>;
+ pinctrl-names = "default";
+ tx_delay = <0x44>;
+ rx_delay = <0x00>;
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+
+ tca6424a: gpio-controller@23 {
+ compatible = "ti,tca6424";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-parent = <&gpio1>;
+ interrupts = <RK_PA4 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tca6424a_int>;
+ vcc-supply = <&vcc3v3_sys>;
+ };
+};
+
+&i2c5 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5m2_xfer>;
+
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&i2c7 {
+ status = "okay";
+
+ nau8822: nau8822@1a {
+ compatible = "nuvoton,nau8822";
+ reg = <0x1a>;
+ clocks = <&cru I2S0_8CH_MCLKOUT>;
+ clock-names = "mclk";
+ assigned-clocks = <&cru I2S0_8CH_MCLKOUT>;
+ assigned-clock-rates = <12288000>;
+ #sound-dai-cells = <0>;
+ };
+};
+
+
+&i2s0_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_lrck
+ &i2s0_mclk
+ &i2s0_sclk
+ &i2s0_sdi0
+ &i2s0_sdo0>;
+ status = "okay";
+};
+
+&mdio0 {
+ rgmii_phy0: ethernet-phy@1 {
+ /* RTL8211F */
+ compatible = "ethernet-phy-id001c.c916",
+ "ethernet-phy-ieee802.3-c22";
+ reg = <0x1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rtl8211f_0_rst>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&gpio0 RK_PB0 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@2 {
+ /* RTL8211F */
+ compatible = "ethernet-phy-id001c.c916",
+ "ethernet-phy-ieee802.3-c22";
+ reg = <0x2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rtl8211f_1_rst>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&pcie2x1l0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie2_0_rst>;
+ reset-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie2x1l0>;
+ status = "okay";
+};
+
+&pcie2x1l2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie2_2_rst>;
+ reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie2x1l2>;
+ status = "okay";
+};
+
+&pcie30phy {
+ status = "okay";
+};
+
+&pcie3x4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie3_rst>;
+ reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie30>;
+ status = "okay";
+};
+
+&pinctrl {
+ audio {
+ hp_detect: hp-detect {
+ rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ rtl8211f {
+ rtl8211f_0_rst: rtl8211f-0-rst {
+ rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ rtl8211f_1_rst: rtl8211f-1-rst {
+ rockchip,pins = <1 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ tca6424a {
+ tca6424a_int: tca6424a-int {
+ rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ pcie2 {
+ pcie2_0_rst: pcie2-0-rst {
+ rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ pcie2_2_rst: pcie2-2-rst {
+ rockchip,pins = <3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie3 {
+ pcie3_rst: pcie3-rst {
+ rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&avcc_1v8_s0>;
+ status = "okay";
+};
+
+&sdmmc {
+ max-frequency = <200000000>;
+ no-sdio;
+ no-mmc;
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_3v3_s3>;
+ vqmmc-supply = <&vccio_sd_s0>;
+ status = "okay";
+};
+
+&u2phy2 {
+ status = "okay";
+};
+
+&u2phy2_host {
+ status = "okay";
+};
+
+&u2phy3 {
+ status = "okay";
+};
+
+&u2phy3_host {
+ status = "okay";
+};
OK3588-C is the carrier board for FET3588-C System on Module. OK3588-C features: - 2x 1GbE Realtek RTL8211F Ethernet - 1x HDMI Type A out - 1x HDMI Type A in - 3x USB 3.1 Type C (2x OTG and 1x serial console) - 1x USB 2.0 Type A - 1x USB 3.0 & USB 2.0 Combo M.2 M Key (4G/5G modem) - 1x PCIE 2.0 M.2 E Key (1 lane) - 1x PCIE 2.0 PCIe (1 lane) - 1x PCIE 3.0 PCIe (4 lanes) - 1x TF scard slot - 5x MIPI CSI - 2x MIP DSI - 2x CAN2.0B - 1x RS485 - 1x NAU8822 onboard audio - 1x FAN connector - 1x RTC - 20-pin expansion header - ADC keys Add support for Forlinx OK3588-C board. Signed-off-by: Dmitry Yashin <dmt.yashin@gmail.com> --- arch/arm64/boot/dts/rockchip/Makefile | 1 + .../boot/dts/rockchip/rk3588-ok3588-c.dts | 390 ++++++++++++++++++ 2 files changed, 391 insertions(+) create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-ok3588-c.dts