@@ -884,6 +884,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-ipq4019-ap.dk07.1-c1.dtb \
qcom-ipq4019-ap.dk07.1-c2.dtb \
qcom-ipq8064-ap148.dtb \
+ qcom-ipq8064-rb3011.dtb \
qcom-msm8660-surf.dtb \
qcom-msm8960-cdp.dtb \
qcom-msm8974-fairphone-fp2.dtb \
new file mode 100644
@@ -0,0 +1,308 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-ipq8064.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "MikroTik RB3011UiAS-RM";
+ compatible = "mikrotik,rb3011";
+
+ aliases {
+ serial0 = &gsbi7_serial;
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac3;
+ mdio-gpio0 = &mdio0;
+ mdio-gpio1 = &mdio1;
+ };
+
+ chosen {
+ bootargs = "loglevel=8 console=ttyMSM0,115200";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ reg = <0x42000000 0x3e000000>;
+ device_type = "memory";
+ };
+
+ mdio0: mdio@0 {
+ status = "okay";
+ compatible = "virtual,mdio-gpio";
+ gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
+ <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ switch0: switch@10 {
+ compatible = "qca,qca8337";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dsa,member = <0 0>;
+
+ pinctrl-0 = <&sw0_reset_pin>;
+ pinctrl-names = "default";
+
+ reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
+ reg = <0x10>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch0cpu: port@0 {
+ reg = <0>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "rgmii-id";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "sw1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "sw2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "sw3";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "sw4";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "sw5";
+ };
+ };
+ };
+ };
+
+ mdio1: mdio@1 {
+ status = "okay";
+ compatible = "virtual,mdio-gpio";
+ gpios = <&qcom_pinmux 11 GPIO_ACTIVE_HIGH>,
+ <&qcom_pinmux 10 GPIO_ACTIVE_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&mdio1_pins>;
+ pinctrl-names = "default";
+
+ switch1: switch@14 {
+ compatible = "qca,qca8337";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dsa,member = <1 0>;
+
+ pinctrl-0 = <&sw1_reset_pin>;
+ pinctrl-names = "default";
+
+ reset-gpios = <&qcom_pinmux 17 GPIO_ACTIVE_LOW>;
+ reg = <0x10>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch1cpu: port@0 {
+ reg = <0>;
+ label = "cpu";
+ ethernet = <&gmac3>;
+ phy-mode = "sgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "sw6";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "sw7";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "sw8";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "sw9";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "sw10";
+ };
+ };
+ };
+ };
+
+ soc {
+ gsbi5: gsbi@1a200000 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "okay";
+
+ spi4: spi@1a280000 {
+ status = "okay";
+ spi-max-frequency = <50000000>;
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+ norflash: s25fl016k@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ partition@0 {
+ label = "RouterBoot";
+ reg = <0x0 0x40000>;
+ };
+ };
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&buttons_pins>;
+ pinctrl-names = "default";
+
+ button@1 {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&qcom_pinmux 66 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&leds_pins>;
+ pinctrl-names = "default";
+
+ led@7 {
+ label = "rb3011:green:user";
+ gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ };
+};
+
+&gmac0 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+ qcom,id = <0>;
+ phy-handle = <&switch0cpu>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac3 {
+ status = "okay";
+
+ phy-mode = "sgmii";
+ qcom,id = <3>;
+ phy-handle = <&switch1cpu>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gsbi7 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+};
+
+&gsbi7_serial {
+ status = "okay";
+};
+
+&qcom_pinmux {
+ buttons_pins: buttons_pins {
+ mux {
+ pins = "gpio66";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ leds_pins: leds_pins {
+ mux {
+ pins = "gpio33";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ mdio1_pins: mdio1_pins {
+ mux {
+ pins = "gpio10", "gpio11";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ sw0_reset_pin: sw0_reset_pin {
+ mux {
+ pins = "gpio16";
+ drive-strength = <16>;
+ function = "gpio";
+ bias-disable;
+ input-disable;
+ };
+ };
+
+ sw1_reset_pin: sw1_reset_pin {
+ mux {
+ pins = "gpio17";
+ drive-strength = <16>;
+ function = "gpio";
+ bias-disable;
+ input-disable;
+ };
+ };
+};
This patch adds a DTS file for the MikroTik RouterBoard 3011, which is a 1U rackmount router based on the IPQ8064, supporting the serial UART, dual QCA8337 Gigabit ethernet switches, boot loader NOR and user LED device. Signed-off-by: Jonathan McDowell <noodles@earth.li> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 308 ++++++++++++++++++++++ 2 files changed, 309 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-ipq8064-rb3011.dts