| Message ID | 784d0d08ee585fc436f15de4edb58b394d0f4452.1567878413.git.hns@goldelico.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | OMAP3: convert opp-v1 to opp-v2 and read speed binned / 720MHz grade bits | expand |
On Sat, Sep 7, 2019 at 12:47 PM H. Nikolaus Schaller <hns@goldelico.com> wrote: > > In addition, move omap3 from whitelist to blacklist in cpufreq-dt-platdev > in the same patch, because doing either first breaks operation and > may make trouble in bisect. > > We also can remove opp-v1 table for omap3-n950-n9 since it is now > automatically detected. > > We also fix a wrong OPP4 voltage for omap3430 which must be > 0.6V + 54*12.5mV = 1275mV. Otherwise the twl4030 driver will reject > this OPP. > thank you for your work on this. I tested it on a a Logit PD DM3730 Torpedo + Wireless kit, and appears to operate normally, but i have not tested it at temperature. Tested-by: Adam Ford <aford173@gmail.com> > Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> > Acked-by: Tony Lindgren <tony@atomide.com> > --- > arch/arm/boot/dts/omap3-n950-n9.dtsi | 7 --- > arch/arm/boot/dts/omap34xx.dtsi | 65 ++++++++++++++++++++++++---- > arch/arm/boot/dts/omap36xx.dtsi | 53 +++++++++++++++++++---- > drivers/cpufreq/cpufreq-dt-platdev.c | 2 +- > 4 files changed, 102 insertions(+), 25 deletions(-) > > diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/omap3-n950-n9.dtsi > index 5441e9ffdbb4..e98b0c615f19 100644 > --- a/arch/arm/boot/dts/omap3-n950-n9.dtsi > +++ b/arch/arm/boot/dts/omap3-n950-n9.dtsi > @@ -11,13 +11,6 @@ > cpus { > cpu@0 { > cpu0-supply = <&vcc>; > - operating-points = < > - /* kHz uV */ > - 300000 1012500 > - 600000 1200000 > - 800000 1325000 > - 1000000 1375000 > - >; > }; > }; > > diff --git a/arch/arm/boot/dts/omap34xx.dtsi b/arch/arm/boot/dts/omap34xx.dtsi > index f572a477f74c..91154829f86a 100644 > --- a/arch/arm/boot/dts/omap34xx.dtsi > +++ b/arch/arm/boot/dts/omap34xx.dtsi > @@ -16,19 +16,66 @@ > / { > cpus { > cpu: cpu@0 { > - /* OMAP343x/OMAP35xx variants OPP1-5 */ > - operating-points = < > - /* kHz uV */ > - 125000 975000 > - 250000 1075000 > - 500000 1200000 > - 550000 1270000 > - 600000 1350000 > - >; > + /* OMAP343x/OMAP35xx variants OPP1-6 */ > + operating-points-v2 = <&cpu0_opp_table>; > + > clock-latency = <300000>; /* From legacy driver */ > }; > }; > > + /* see Documentation/devicetree/bindings/opp/opp.txt */ > + cpu0_opp_table: opp-table { > + compatible = "operating-points-v2-ti-cpu"; > + syscon = <&scm_conf>; > + > + opp1-125000000 { > + opp-hz = /bits/ 64 <125000000>; > + /* > + * we currently only select the max voltage from table > + * Table 3-3 of the omap3530 Data sheet (SPRS507F). > + * Format is: <target min max> > + */ > + opp-microvolt = <975000 975000 975000>; > + /* > + * first value is silicon revision bit mask > + * second one 720MHz Device Identification bit mask > + */ > + opp-supported-hw = <0xffffffff 3>; > + }; > + > + opp2-250000000 { > + opp-hz = /bits/ 64 <250000000>; > + opp-microvolt = <1075000 1075000 1075000>; > + opp-supported-hw = <0xffffffff 3>; > + opp-suspend; > + }; > + > + opp3-500000000 { > + opp-hz = /bits/ 64 <500000000>; > + opp-microvolt = <1200000 1200000 1200000>; > + opp-supported-hw = <0xffffffff 3>; > + }; > + > + opp4-550000000 { > + opp-hz = /bits/ 64 <550000000>; > + opp-microvolt = <1275000 1275000 1275000>; > + opp-supported-hw = <0xffffffff 3>; > + }; > + > + opp5-600000000 { > + opp-hz = /bits/ 64 <600000000>; > + opp-microvolt = <1350000 1350000 1350000>; > + opp-supported-hw = <0xffffffff 3>; > + }; > + > + opp6-720000000 { > + opp-hz = /bits/ 64 <720000000>; > + opp-microvolt = <1350000 1350000 1350000>; > + /* only high-speed grade omap3530 devices */ > + opp-supported-hw = <0xffffffff 2>; > + }; > + }; > + > ocp@68000000 { > omap3_pmx_core2: pinmux@480025d8 { > compatible = "ti,omap3-padconf", "pinctrl-single"; > diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi > index 6fb23ada1f64..44f25b0eb45b 100644 > --- a/arch/arm/boot/dts/omap36xx.dtsi > +++ b/arch/arm/boot/dts/omap36xx.dtsi > @@ -19,15 +19,52 @@ > }; > > cpus { > - /* OMAP3630/OMAP37xx 'standard device' variants OPP50 to OPP130 */ > + /* OMAP3630/OMAP37xx variants OPP50 to OPP130 and OPP1G */ > cpu: cpu@0 { > - operating-points = < > - /* kHz uV */ > - 300000 1012500 > - 600000 1200000 > - 800000 1325000 > - >; > - clock-latency = <300000>; /* From legacy driver */ > + operating-points-v2 = <&cpu0_opp_table>; > + > + clock-latency = <300000>; /* From omap-cpufreq driver */ > + }; > + }; > + > + /* see Documentation/devicetree/bindings/opp/opp.txt */ > + cpu0_opp_table: opp-table { > + compatible = "operating-points-v2-ti-cpu"; > + syscon = <&scm_conf>; > + > + opp50-300000000 { > + opp-hz = /bits/ 64 <300000000>; > + /* > + * we currently only select the max voltage from table > + * Table 4-19 of the DM3730 Data sheet (SPRS685B) > + * Format is: <target min max> > + */ > + opp-microvolt = <1012500 1012500 1012500>; > + /* > + * first value is silicon revision bit mask > + * second one is "speed binned" bit mask > + */ > + opp-supported-hw = <0xffffffff 3>; > + opp-suspend; > + }; > + > + opp100-600000000 { > + opp-hz = /bits/ 64 <600000000>; > + opp-microvolt = <1200000 1200000 1200000>; > + opp-supported-hw = <0xffffffff 3>; > + }; > + > + opp130-800000000 { > + opp-hz = /bits/ 64 <800000000>; > + opp-microvolt = <1325000 1325000 1325000>; > + opp-supported-hw = <0xffffffff 3>; > + }; > + > + opp1g-1000000000 { > + opp-hz = /bits/ 64 <1000000000>; > + opp-microvolt = <1375000 1375000 1375000>; > + /* only on am/dm37x with speed-binned bit set */ > + opp-supported-hw = <0xffffffff 2>; > }; > }; > > diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c > index 03dc4244ab00..68b7fc4225f8 100644 > --- a/drivers/cpufreq/cpufreq-dt-platdev.c > +++ b/drivers/cpufreq/cpufreq-dt-platdev.c > @@ -86,7 +86,6 @@ static const struct of_device_id whitelist[] __initconst = { > { .compatible = "st-ericsson,u9540", }, > > { .compatible = "ti,omap2", }, > - { .compatible = "ti,omap3", }, > { .compatible = "ti,omap4", }, > { .compatible = "ti,omap5", }, > > @@ -132,6 +131,7 @@ static const struct of_device_id blacklist[] __initconst = { > { .compatible = "ti,am33xx", }, > { .compatible = "ti,am43", }, > { .compatible = "ti,dra7", }, > + { .compatible = "ti,omap3", }, > > { } > }; > -- > 2.19.1 >
diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/omap3-n950-n9.dtsi index 5441e9ffdbb4..e98b0c615f19 100644 --- a/arch/arm/boot/dts/omap3-n950-n9.dtsi +++ b/arch/arm/boot/dts/omap3-n950-n9.dtsi @@ -11,13 +11,6 @@ cpus { cpu@0 { cpu0-supply = <&vcc>; - operating-points = < - /* kHz uV */ - 300000 1012500 - 600000 1200000 - 800000 1325000 - 1000000 1375000 - >; }; }; diff --git a/arch/arm/boot/dts/omap34xx.dtsi b/arch/arm/boot/dts/omap34xx.dtsi index f572a477f74c..91154829f86a 100644 --- a/arch/arm/boot/dts/omap34xx.dtsi +++ b/arch/arm/boot/dts/omap34xx.dtsi @@ -16,19 +16,66 @@ / { cpus { cpu: cpu@0 { - /* OMAP343x/OMAP35xx variants OPP1-5 */ - operating-points = < - /* kHz uV */ - 125000 975000 - 250000 1075000 - 500000 1200000 - 550000 1270000 - 600000 1350000 - >; + /* OMAP343x/OMAP35xx variants OPP1-6 */ + operating-points-v2 = <&cpu0_opp_table>; + clock-latency = <300000>; /* From legacy driver */ }; }; + /* see Documentation/devicetree/bindings/opp/opp.txt */ + cpu0_opp_table: opp-table { + compatible = "operating-points-v2-ti-cpu"; + syscon = <&scm_conf>; + + opp1-125000000 { + opp-hz = /bits/ 64 <125000000>; + /* + * we currently only select the max voltage from table + * Table 3-3 of the omap3530 Data sheet (SPRS507F). + * Format is: <target min max> + */ + opp-microvolt = <975000 975000 975000>; + /* + * first value is silicon revision bit mask + * second one 720MHz Device Identification bit mask + */ + opp-supported-hw = <0xffffffff 3>; + }; + + opp2-250000000 { + opp-hz = /bits/ 64 <250000000>; + opp-microvolt = <1075000 1075000 1075000>; + opp-supported-hw = <0xffffffff 3>; + opp-suspend; + }; + + opp3-500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <1200000 1200000 1200000>; + opp-supported-hw = <0xffffffff 3>; + }; + + opp4-550000000 { + opp-hz = /bits/ 64 <550000000>; + opp-microvolt = <1275000 1275000 1275000>; + opp-supported-hw = <0xffffffff 3>; + }; + + opp5-600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <1350000 1350000 1350000>; + opp-supported-hw = <0xffffffff 3>; + }; + + opp6-720000000 { + opp-hz = /bits/ 64 <720000000>; + opp-microvolt = <1350000 1350000 1350000>; + /* only high-speed grade omap3530 devices */ + opp-supported-hw = <0xffffffff 2>; + }; + }; + ocp@68000000 { omap3_pmx_core2: pinmux@480025d8 { compatible = "ti,omap3-padconf", "pinctrl-single"; diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi index 6fb23ada1f64..44f25b0eb45b 100644 --- a/arch/arm/boot/dts/omap36xx.dtsi +++ b/arch/arm/boot/dts/omap36xx.dtsi @@ -19,15 +19,52 @@ }; cpus { - /* OMAP3630/OMAP37xx 'standard device' variants OPP50 to OPP130 */ + /* OMAP3630/OMAP37xx variants OPP50 to OPP130 and OPP1G */ cpu: cpu@0 { - operating-points = < - /* kHz uV */ - 300000 1012500 - 600000 1200000 - 800000 1325000 - >; - clock-latency = <300000>; /* From legacy driver */ + operating-points-v2 = <&cpu0_opp_table>; + + clock-latency = <300000>; /* From omap-cpufreq driver */ + }; + }; + + /* see Documentation/devicetree/bindings/opp/opp.txt */ + cpu0_opp_table: opp-table { + compatible = "operating-points-v2-ti-cpu"; + syscon = <&scm_conf>; + + opp50-300000000 { + opp-hz = /bits/ 64 <300000000>; + /* + * we currently only select the max voltage from table + * Table 4-19 of the DM3730 Data sheet (SPRS685B) + * Format is: <target min max> + */ + opp-microvolt = <1012500 1012500 1012500>; + /* + * first value is silicon revision bit mask + * second one is "speed binned" bit mask + */ + opp-supported-hw = <0xffffffff 3>; + opp-suspend; + }; + + opp100-600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <1200000 1200000 1200000>; + opp-supported-hw = <0xffffffff 3>; + }; + + opp130-800000000 { + opp-hz = /bits/ 64 <800000000>; + opp-microvolt = <1325000 1325000 1325000>; + opp-supported-hw = <0xffffffff 3>; + }; + + opp1g-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <1375000 1375000 1375000>; + /* only on am/dm37x with speed-binned bit set */ + opp-supported-hw = <0xffffffff 2>; }; }; diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c index 03dc4244ab00..68b7fc4225f8 100644 --- a/drivers/cpufreq/cpufreq-dt-platdev.c +++ b/drivers/cpufreq/cpufreq-dt-platdev.c @@ -86,7 +86,6 @@ static const struct of_device_id whitelist[] __initconst = { { .compatible = "st-ericsson,u9540", }, { .compatible = "ti,omap2", }, - { .compatible = "ti,omap3", }, { .compatible = "ti,omap4", }, { .compatible = "ti,omap5", }, @@ -132,6 +131,7 @@ static const struct of_device_id blacklist[] __initconst = { { .compatible = "ti,am33xx", }, { .compatible = "ti,am43", }, { .compatible = "ti,dra7", }, + { .compatible = "ti,omap3", }, { } };