diff mbox series

[v2,3/3] arm64: dts: ti: iot2050: Add support for M.2 variant

Message ID 878e3a023767b5a6d9d2cff09015678aaba13fce.1674110442.git.jan.kiszka@siemens.com (mailing list archive)
State New, archived
Headers show
Series arm64: dts: Add IOT2050 M.2 board, describe QSPI layout | expand

Commit Message

Jan Kiszka Jan. 19, 2023, 6:40 a.m. UTC 
From: chao zeng <chao.zeng@siemens.com>

The M.2 variant comes with 2 slots, one B-keyed and another one E-keyed.
They are configured by the firmware during startup. Also the device tree
will be adjusted according to the detect or manually configured
interface mode by the firmware. The kernel only carries a single
configuration as base device tree. It has to be built with a symbols
node so that the firmware can apply overlays for the connector modes.

Signed-off-by: chao zeng <chao.zeng@siemens.com>
[Jan: refactored to a single DT]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
 arch/arm64/boot/dts/ti/Makefile               |   3 +
 .../dts/ti/k3-am6548-iot2050-advanced-m2.dts  | 121 ++++++++++++++++++
 2 files changed, 124 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts

Comments

Siddharth Vadapalli Jan. 25, 2023, 6:11 a.m. UTC | #1 
On 19/01/23 12:10, Jan Kiszka wrote:
> From: chao zeng <chao.zeng@siemens.com>
> 
> The M.2 variant comes with 2 slots, one B-keyed and another one E-keyed.
> They are configured by the firmware during startup. Also the device tree
> will be adjusted according to the detect or manually configured
> interface mode by the firmware. The kernel only carries a single
> configuration as base device tree. It has to be built with a symbols
> node so that the firmware can apply overlays for the connector modes.
> 
> Signed-off-by: chao zeng <chao.zeng@siemens.com>
> [Jan: refactored to a single DT]
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
> ---
>  arch/arm64/boot/dts/ti/Makefile               |   3 +
>  .../dts/ti/k3-am6548-iot2050-advanced-m2.dts  | 121 ++++++++++++++++++
>  2 files changed, 124 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts

Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>

Regards,
Siddharth.
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index cf7c509538a4..bfb16b62c58d 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -10,8 +10,11 @@  dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic-pg2.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-m2.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb
 
+DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
+
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
new file mode 100644
index 000000000000..9400e35882a6
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
@@ -0,0 +1,121 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2018-2023
+ *
+ * Authors:
+ *   Chao Zeng <chao.zeng@siemens.com>
+ *   Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * AM6548-based (quad-core) IOT2050 M.2 variant (based on Advanced Product
+ * Generation 2), 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
+ */
+
+#include "k3-am6548-iot2050-advanced-common.dtsi"
+#include "k3-am65-iot2050-common-pg2.dtsi"
+
+/ {
+	compatible = "siemens,iot2050-advanced-m2", "ti,am654";
+	model = "SIMATIC IOT2050 Advanced M2";
+};
+
+&mcu_r5fss0 {
+	/* lock-step mode not supported on this board */
+	ti,cluster-mode = <0>;
+};
+
+&main_pmx0 {
+	main_m2_enable_pins_default: main-m2-enable-pins-default {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x01c4, PIN_INPUT_PULLUP, 7)  /* (AH13) GPIO1_17 */
+		>;
+	};
+
+	main_bkey_pcie_reset: main-bkey-pcie-reset {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x01bc, PIN_OUTPUT_PULLUP, 7)  /* (AG13) GPIO1_15 */
+		>;
+	};
+
+	main_pmx0_m2_config_pins_default: main-pmx0-m2-config-pins-default {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x01c8, PIN_INPUT_PULLUP, 7)  /* (AE13) GPIO1_18 */
+			AM65X_IOPAD(0x01cc, PIN_INPUT_PULLUP, 7)  /* (AD13) GPIO1_19 */
+		>;
+	};
+
+	main_m2_pcie_mux_control: main-m2-pcie-mux-control {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x0148, PIN_INPUT_PULLUP, 7)  /* (AG22) GPIO0_82 */
+			AM65X_IOPAD(0x0160, PIN_INPUT_PULLUP, 7)  /* (AE20) GPIO0_88 */
+			AM65X_IOPAD(0x0164, PIN_INPUT_PULLUP, 7)  /* (AF19) GPIO0_89 */
+		>;
+	};
+};
+
+&main_pmx1 {
+	main_pmx1_m2_config_pins_default: main-pmx1-m2-config-pins-default {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x0018, PIN_INPUT_PULLUP, 7)  /* (B22) GPIO1_88 */
+			AM65X_IOPAD(0x001c, PIN_INPUT_PULLUP, 7)  /* (C23) GPIO1_89 */
+		>;
+	};
+};
+
+&main_gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&main_m2_pcie_mux_control
+		&arduino_io_d4_to_d9_pins_default
+	>;
+};
+
+&main_gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&main_m2_enable_pins_default
+		&main_pmx0_m2_config_pins_default
+		&main_pmx1_m2_config_pins_default
+		&cp2102n_reset_pin_default
+	>;
+};
+
+/*
+ * Base configuration for B-key slot with PCIe x2, E-key with USB 2.0 only.
+ * Firmware switches to other modes via device tree overlays.
+ */
+
+&serdes0 {
+	assigned-clocks = <&k3_clks 153 4>, <&serdes0 AM654_SERDES_CMU_REFCLK>;
+	assigned-clock-parents = <&k3_clks 153 8>, <&k3_clks 153 4>;
+};
+
+&pcie0_rc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_bkey_pcie_reset>;
+
+	num-lanes = <2>;
+	phys = <&serdes0 PHY_TYPE_PCIE 1>, <&serdes1 PHY_TYPE_PCIE 1>;
+	phy-names = "pcie-phy0","pcie-phy1";
+	reset-gpios = <&main_gpio1 15 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&pcie1_rc {
+	status = "disabled";
+};
+
+&dwc3_0 {
+	assigned-clock-parents = <&k3_clks 151 4>,  /* set REF_CLK to 20MHz i.e. PER0_PLL/48 */
+				 <&k3_clks 151 9>;  /* set PIPE3_TXB_CLK to CLK_12M_RC/256 (for HS only) */
+	/delete-property/ phys;
+	/delete-property/ phy-names;
+};
+
+&usb0 {
+	maximum-speed = "high-speed";
+	/delete-property/ snps,dis-u1-entry-quirk;
+	/delete-property/ snps,dis-u2-entry-quirk;
+};