@@ -24,5 +24,6 @@ extern void r8a7778_init_delay(void);
extern void r8a7778_init_irq(void);
extern void r8a7778_init_irq_dt(void);
extern void r8a7778_clock_init(void);
+extern void r8a7778_init_irq_extpin(int irlm);
#endif /* __ASM_R8A7778_H__ */
@@ -23,6 +23,7 @@
#include <linux/irqchip/arm-gic.h>
#include <linux/of.h>
#include <linux/of_platform.h>
+#include <linux/platform_data/irq-renesas-intc-irqpin.h>
#include <linux/platform_device.h>
#include <linux/irqchip.h>
#include <linux/serial_sci.h>
@@ -110,6 +111,49 @@ void __init r8a7778_add_standard_devices(void)
r8a7778_register_tmu(1);
}
+static struct renesas_intc_irqpin_config irqpin_platform_data = {
+ .irq_base = irq_pin(0), /* IRQ0 -> IRQ3 */
+ .sense_bitfield_width = 2,
+};
+
+static struct resource irqpin_resources[] = {
+ DEFINE_RES_MEM(0xfe78001c, 4), /* ICR1 */
+ DEFINE_RES_MEM(0xfe780010, 4), /* INTPRI */
+ DEFINE_RES_MEM(0xfe780024, 4), /* INTREQ */
+ DEFINE_RES_MEM(0xfe780044, 4), /* INTMSK0 */
+ DEFINE_RES_MEM(0xfe780064, 4), /* INTMSKCLR0 */
+ DEFINE_RES_IRQ(gic_iid(0x3b)), /* IRQ0 */
+ DEFINE_RES_IRQ(gic_iid(0x3c)), /* IRQ1 */
+ DEFINE_RES_IRQ(gic_iid(0x3d)), /* IRQ2 */
+ DEFINE_RES_IRQ(gic_iid(0x3e)), /* IRQ3 */
+};
+
+void __init r8a7778_init_irq_extpin(int irlm)
+{
+ void __iomem *icr0 = ioremap_nocache(0xfe780000, PAGE_SIZE);
+ unsigned long tmp;
+
+ if (!icr0) {
+ pr_warn("r8a7778: unable to setup external irq pin mode\n");
+ return;
+ }
+
+ tmp = ioread32(icr0);
+ if (irlm)
+ tmp |= 1 << 23; /* IRQ0 -> IRQ3 as individual pins */
+ else
+ tmp &= ~(1 << 23); /* IRL mode - not supported */
+ tmp |= (1 << 21); /* LVLMODE = 1 */
+ iowrite32(tmp, icr0);
+ iounmap(icr0);
+
+ if (irlm)
+ platform_device_register_resndata(
+ &platform_bus, "renesas_intc_irqpin", -1,
+ irqpin_resources, ARRAY_SIZE(irqpin_resources),
+ &irqpin_platform_data, sizeof(irqpin_platform_data));
+}
+
#define INT2SMSKCR0 0x82288 /* 0xfe782288 */
#define INT2SMSKCR1 0x8228c /* 0xfe78228c */
This patch adds r8a7778_init_irq_extpin() for IRQ0 - IRQ3. But this patch doesn't enable DT settings on r8a7778.dts, because R8A7778 chip external IRQ depends on IRQ0 - IRQ3 pin encoding which came from platform board implementation. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> --- v2 -> v3 - no change arch/arm/mach-shmobile/include/mach/r8a7778.h | 1 + arch/arm/mach-shmobile/setup-r8a7778.c | 44 +++++++++++++++++++++++++ 2 files changed, 45 insertions(+)