diff mbox series

[01/23] arm64: zynqmp: Describe TI phy as ethernet-phy-id

Message ID 9eefc40c727928e0c7b794a3a2e061ecf6ea230c.1683034376.git.michal.simek@amd.com (mailing list archive)
State New, archived
Headers show
Series arm64: zynqmp: Misc zynqmp changes | expand

Commit Message

Michal Simek May 2, 2023, 1:35 p.m. UTC 
TI DP83867 is using strapping based on MIO pins. Tristate setup can influce
PHY address. That's why switch description with ethernet-phy-id compatible
string which enable calling reset. PHY itself setups phy address after
power up or reset.
Phy reset is done via gpio.

Signed-off-by: Michal Simek <michal.simek@amd.com>
---

Checkpatch is reporting issue
warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented
but it should be fully aligned with
Documentation/devicetree/bindings/net/ethernet-phy.yaml
---
 .../boot/dts/xilinx/zynqmp-zcu102-revA.dts    | 23 +++++++++++------
 .../boot/dts/xilinx/zynqmp-zcu102-revB.dts    | 25 +++++++++++--------
 .../boot/dts/xilinx/zynqmp-zcu104-revA.dts    | 22 ++++++++++------
 .../boot/dts/xilinx/zynqmp-zcu104-revC.dts    | 22 ++++++++++------
 .../boot/dts/xilinx/zynqmp-zcu106-revA.dts    | 22 ++++++++++------
 .../boot/dts/xilinx/zynqmp-zcu111-revA.dts    | 22 ++++++++++------
 6 files changed, 90 insertions(+), 46 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
index 13c43324f1d2..c193579400cf 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
@@ -2,7 +2,8 @@ 
 /*
  * dts file for Xilinx ZynqMP ZCU102 RevA
  *
- * (C) Copyright 2015 - 2021, Xilinx, Inc.
+ * (C) Copyright 2015 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -200,13 +201,19 @@  &gem3 {
 	phy-mode = "rgmii-id";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gem3_default>;
-	phy0: ethernet-phy@21 {
-		reg = <21>;
-		ti,rx-internal-delay = <0x8>;
-		ti,tx-internal-delay = <0xa>;
-		ti,fifo-depth = <0x1>;
-		ti,dp83867-rxctrl-strap-quirk;
-		/* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy0: ethernet-phy@21 {
+			#phy-cells = <1>;
+			compatible = "ethernet-phy-id2000.a231";
+			reg = <21>;
+			ti,rx-internal-delay = <0x8>;
+			ti,tx-internal-delay = <0xa>;
+			ti,fifo-depth = <0x1>;
+			ti,dp83867-rxctrl-strap-quirk;
+			reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
+		};
 	};
 };
 
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
index f7d718ff116b..00b930f20718 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
@@ -2,7 +2,8 @@ 
 /*
  * dts file for Xilinx ZynqMP ZCU102 RevB
  *
- * (C) Copyright 2016 - 2021, Xilinx, Inc.
+ * (C) Copyright 2016 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -16,16 +17,20 @@  / {
 
 &gem3 {
 	phy-handle = <&phyc>;
-	phyc: ethernet-phy@c {
-		reg = <0xc>;
-		ti,rx-internal-delay = <0x8>;
-		ti,tx-internal-delay = <0xa>;
-		ti,fifo-depth = <0x1>;
-		ti,dp83867-rxctrl-strap-quirk;
-		/* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
+	mdio: mdio {
+		phyc: ethernet-phy@c {
+			#phy-cells = <0x1>;
+			compatible = "ethernet-phy-id2000.a231";
+			reg = <0xc>;
+			ti,rx-internal-delay = <0x8>;
+			ti,tx-internal-delay = <0xa>;
+			ti,fifo-depth = <0x1>;
+			ti,dp83867-rxctrl-strap-quirk;
+			reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
+		};
+		/* Cleanup from RevA */
+		/delete-node/ ethernet-phy@21;
 	};
-	/* Cleanup from RevA */
-	/delete-node/ ethernet-phy@21;
 };
 
 /* Fix collision with u61 */
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
index 485585c491f4..11c1eaef9f53 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
@@ -2,7 +2,8 @@ 
 /*
  * dts file for Xilinx ZynqMP ZCU104
  *
- * (C) Copyright 2017 - 2021, Xilinx, Inc.
+ * (C) Copyright 2017 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -109,12 +110,19 @@  &gem3 {
 	phy-mode = "rgmii-id";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gem3_default>;
-	phy0: ethernet-phy@c {
-		reg = <0xc>;
-		ti,rx-internal-delay = <0x8>;
-		ti,tx-internal-delay = <0xa>;
-		ti,fifo-depth = <0x1>;
-		ti,dp83867-rxctrl-strap-quirk;
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy0: ethernet-phy@c {
+			#phy-cells = <1>;
+			compatible = "ethernet-phy-id2000.a231";
+			reg = <0xc>;
+			ti,rx-internal-delay = <0x8>;
+			ti,tx-internal-delay = <0xa>;
+			ti,fifo-depth = <0x1>;
+			ti,dp83867-rxctrl-strap-quirk;
+			reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
+		};
 	};
 };
 
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
index 44ec9edd2452..c06c138fa3e5 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
@@ -2,7 +2,8 @@ 
 /*
  * dts file for Xilinx ZynqMP ZCU104
  *
- * (C) Copyright 2017 - 2021, Xilinx, Inc.
+ * (C) Copyright 2017 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -114,12 +115,19 @@  &gem3 {
 	phy-mode = "rgmii-id";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gem3_default>;
-	phy0: ethernet-phy@c {
-		reg = <0xc>;
-		ti,rx-internal-delay = <0x8>;
-		ti,tx-internal-delay = <0xa>;
-		ti,fifo-depth = <0x1>;
-		ti,dp83867-rxctrl-strap-quirk;
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy0: ethernet-phy@c {
+			#phy-cells = <1>;
+			compatible = "ethernet-phy-id2000.a231";
+			reg = <0xc>;
+			ti,rx-internal-delay = <0x8>;
+			ti,tx-internal-delay = <0xa>;
+			ti,fifo-depth = <0x1>;
+			ti,dp83867-rxctrl-strap-quirk;
+			reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
+		};
 	};
 };
 
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
index 09773b7200f8..52cdec33f190 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
@@ -2,7 +2,8 @@ 
 /*
  * dts file for Xilinx ZynqMP ZCU106
  *
- * (C) Copyright 2016 - 2021, Xilinx, Inc.
+ * (C) Copyright 2016 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -212,12 +213,19 @@  &gem3 {
 	phy-mode = "rgmii-id";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gem3_default>;
-	phy0: ethernet-phy@c {
-		reg = <0xc>;
-		ti,rx-internal-delay = <0x8>;
-		ti,tx-internal-delay = <0xa>;
-		ti,fifo-depth = <0x1>;
-		ti,dp83867-rxctrl-strap-quirk;
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy0: ethernet-phy@c {
+			#phy-cells = <1>;
+			reg = <0xc>;
+			compatible = "ethernet-phy-id2000.a231";
+			ti,rx-internal-delay = <0x8>;
+			ti,tx-internal-delay = <0xa>;
+			ti,fifo-depth = <0x1>;
+			ti,dp83867-rxctrl-strap-quirk;
+			reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
+		};
 	};
 };
 
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
index e0305dcbb010..699cc9ce7898 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
@@ -2,7 +2,8 @@ 
 /*
  * dts file for Xilinx ZynqMP ZCU111
  *
- * (C) Copyright 2017 - 2021, Xilinx, Inc.
+ * (C) Copyright 2017 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -172,12 +173,19 @@  &gem3 {
 	phy-mode = "rgmii-id";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gem3_default>;
-	phy0: ethernet-phy@c {
-		reg = <0xc>;
-		ti,rx-internal-delay = <0x8>;
-		ti,tx-internal-delay = <0xa>;
-		ti,fifo-depth = <0x1>;
-		ti,dp83867-rxctrl-strap-quirk;
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy0: ethernet-phy@c {
+			#phy-cells = <1>;
+			compatible = "ethernet-phy-id2000.a231";
+			reg = <0xc>;
+			ti,rx-internal-delay = <0x8>;
+			ti,tx-internal-delay = <0xa>;
+			ti,fifo-depth = <0x1>;
+			ti,dp83867-rxctrl-strap-quirk;
+			reset-gpios = <&tca6416_u22 6 GPIO_ACTIVE_LOW>;
+		};
 	};
 };