@@ -32,35 +32,9 @@
*/
#define OMAP_SERIAL_NAME "ttyO"
-#define OMAP_MODE13X_SPEED 230400
-
-#define OMAP_UART_SCR_TX_EMPTY 0x08
-
-/* WER = 0x7F
- * Enable module level wakeup in WER reg
- */
-#define OMAP_UART_WER_MOD_WKUP 0X7F
-
-/* Enable XON/XOFF flow control on output */
-#define OMAP_UART_SW_TX 0x08
-
-/* Enable XON/XOFF flow control on input */
-#define OMAP_UART_SW_RX 0x02
-
#define OMAP_UART_SYSC_RESET 0X07
-#define OMAP_UART_TCR_TRIG 0X0F
-#define OMAP_UART_SW_CLR 0XF0
#define OMAP_UART_FIFO_CLR 0X06
-#define OMAP_UART_DMA_CH_FREE -1
-
-#define OMAP_MAX_HSUART_PORTS 4
-
-#define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA
-
-#define UART_ERRATA_i202_MDR1_ACCESS BIT(0)
-#define UART_ERRATA_i291_DMA_FORCEIDLE BIT(1)
-
struct omap_uart_port_info {
bool dma_enabled; /* To specify DMA Mode */
unsigned int uartclk; /* UART clock rate */
@@ -76,65 +50,4 @@ struct omap_uart_port_info {
void (*enable_wakeup)(struct platform_device *, bool);
};
-struct uart_omap_dma {
- u8 uart_dma_tx;
- u8 uart_dma_rx;
- int rx_dma_channel;
- int tx_dma_channel;
- dma_addr_t rx_buf_dma_phys;
- dma_addr_t tx_buf_dma_phys;
- unsigned int uart_base;
- /*
- * Buffer for rx dma.It is not required for tx because the buffer
- * comes from port structure.
- */
- unsigned char *rx_buf;
- unsigned int prev_rx_dma_pos;
- int tx_buf_size;
- int tx_dma_used;
- int rx_dma_used;
- spinlock_t tx_lock;
- spinlock_t rx_lock;
- /* timer to poll activity on rx dma */
- struct timer_list rx_timer;
- unsigned int rx_buf_size;
- unsigned int rx_poll_rate;
- unsigned int rx_timeout;
-};
-
-struct uart_omap_port {
- struct uart_port port;
- struct uart_omap_dma uart_dma;
- struct platform_device *pdev;
-
- unsigned char ier;
- unsigned char lcr;
- unsigned char mcr;
- unsigned char fcr;
- unsigned char efr;
- unsigned char dll;
- unsigned char dlh;
- unsigned char mdr1;
- unsigned char scr;
-
- int use_dma;
- /*
- * Some bits in registers are cleared on a read, so they must
- * be saved whenever the register is read but the bits will not
- * be immediately processed.
- */
- unsigned int lsr_break_flag;
- unsigned char msr_saved_flags;
- char name[20];
- unsigned long port_activity;
- u32 context_loss_cnt;
- u32 errata;
- u8 wakeups_enabled;
-
- struct pm_qos_request pm_qos_request;
- u32 latency;
- u32 calc_latency;
- struct work_struct qos_work;
-};
-
#endif /* __OMAP_SERIAL_H__ */
@@ -44,6 +44,8 @@
#include <plat/dmtimer.h>
#include <plat/omap-serial.h>
+#define OMAP_MAX_HSUART_PORTS 4
+
#define UART_BUILD_REVISION(x, y) (((x) << 8) | (y))
#define OMAP_UART_REV_42 0x0402
@@ -51,6 +53,9 @@
#define OMAP_UART_REV_52 0x0502
#define OMAP_UART_REV_63 0x0603
+#define UART_ERRATA_i202_MDR1_ACCESS BIT(0)
+#define UART_ERRATA_i291_DMA_FORCEIDLE BIT(1)
+
#define DEFAULT_CLK_SPEED 48000000 /* 48Mhz*/
/* SCR register bitmasks */
@@ -71,6 +76,89 @@
#define OMAP_UART_MVR_MAJ_SHIFT 8
#define OMAP_UART_MVR_MIN_MASK 0x3f
+#define OMAP_UART_DMA_CH_FREE -1
+
+#define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA
+#define OMAP_MODE13X_SPEED 230400
+
+#define OMAP_UART_SCR_TX_EMPTY 0x08
+
+/* WER = 0x7F
+ * Enable module level wakeup in WER reg
+ */
+#define OMAP_UART_WER_MOD_WKUP 0X7F
+
+/* Enable XON/XOFF flow control on output */
+#define OMAP_UART_SW_TX 0x08
+
+/* Enable XON/XOFF flow control on input */
+#define OMAP_UART_SW_RX 0x02
+
+#define OMAP_UART_SW_CLR 0xF0
+
+#define OMAP_UART_TCR_TRIG 0x0F
+
+struct uart_omap_dma {
+ u8 uart_dma_tx;
+ u8 uart_dma_rx;
+ int rx_dma_channel;
+ int tx_dma_channel;
+ dma_addr_t rx_buf_dma_phys;
+ dma_addr_t tx_buf_dma_phys;
+ unsigned int uart_base;
+ /*
+ * Buffer for rx dma.It is not required for tx because the buffer
+ * comes from port structure.
+ */
+ unsigned char *rx_buf;
+ unsigned int prev_rx_dma_pos;
+ int tx_buf_size;
+ int tx_dma_used;
+ int rx_dma_used;
+ spinlock_t tx_lock;
+ spinlock_t rx_lock;
+ /* timer to poll activity on rx dma */
+ struct timer_list rx_timer;
+ unsigned int rx_buf_size;
+ unsigned int rx_poll_rate;
+ unsigned int rx_timeout;
+};
+
+struct uart_omap_port {
+ struct uart_port port;
+ struct uart_omap_dma uart_dma;
+ struct platform_device *pdev;
+
+ unsigned char ier;
+ unsigned char lcr;
+ unsigned char mcr;
+ unsigned char fcr;
+ unsigned char efr;
+ unsigned char dll;
+ unsigned char dlh;
+ unsigned char mdr1;
+ unsigned char scr;
+
+ int use_dma;
+ /*
+ * Some bits in registers are cleared on a read, so they must
+ * be saved whenever the register is read but the bits will not
+ * be immediately processed.
+ */
+ unsigned int lsr_break_flag;
+ unsigned char msr_saved_flags;
+ char name[20];
+ unsigned long port_activity;
+ u32 context_loss_cnt;
+ u32 errata;
+ u8 wakeups_enabled;
+
+ struct pm_qos_request pm_qos_request;
+ u32 latency;
+ u32 calc_latency;
+ struct work_struct qos_work;
+};
+
static struct uart_omap_port *serial_omap_port(struct uart_port *port)
{
return container_of(port, struct uart_omap_port, port);
struct uart_omap_port and struct uart_omap_dma, and associated definitions are private to the driver, so there's no point them sitting in an include file under arch/arm. Move them into the driver itself. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> --- arch/arm/plat-omap/include/plat/omap-serial.h | 87 ------------------------ drivers/tty/serial/omap-serial.c | 88 +++++++++++++++++++++++++ 2 files changed, 88 insertions(+), 87 deletions(-)