@@ -1257,29 +1257,11 @@ static int sja1105_parse_dt(struct sja1105_private *priv)
return rc;
}
-/* Convert link speed from SJA1105 to ethtool encoding */
-static int sja1105_port_speed_to_ethtool(struct sja1105_private *priv,
- u64 speed)
-{
- if (speed == priv->info->port_speed[SJA1105_SPEED_10MBPS])
- return SPEED_10;
- if (speed == priv->info->port_speed[SJA1105_SPEED_100MBPS])
- return SPEED_100;
- if (speed == priv->info->port_speed[SJA1105_SPEED_1000MBPS])
- return SPEED_1000;
- if (speed == priv->info->port_speed[SJA1105_SPEED_2500MBPS])
- return SPEED_2500;
- return SPEED_UNKNOWN;
-}
-
-/* Set link speed in the MAC configuration for a specific port. */
-static int sja1105_adjust_port_config(struct sja1105_private *priv, int port,
- int speed_mbps)
+static int sja1105_set_port_speed(struct sja1105_private *priv, int port,
+ int speed_mbps)
{
struct sja1105_mac_config_entry *mac;
- struct device *dev = priv->ds->dev;
u64 speed;
- int rc;
/* On P/Q/R/S, one can read from the device via the MAC reconfiguration
* tables. On E/T, MAC reconfig tables are not readable, only writable.
@@ -1313,7 +1295,7 @@ static int sja1105_adjust_port_config(struct sja1105_private *priv, int port,
speed = priv->info->port_speed[SJA1105_SPEED_2500MBPS];
break;
default:
- dev_err(dev, "Invalid speed %iMbps\n", speed_mbps);
+ dev_err(priv->ds->dev, "Invalid speed %iMbps\n", speed_mbps);
return -EINVAL;
}
@@ -1325,11 +1307,31 @@ static int sja1105_adjust_port_config(struct sja1105_private *priv, int port,
* we need to configure the PCS only (if even that).
*/
if (priv->phy_mode[port] == PHY_INTERFACE_MODE_SGMII)
- mac[port].speed = priv->info->port_speed[SJA1105_SPEED_1000MBPS];
+ speed = priv->info->port_speed[SJA1105_SPEED_1000MBPS];
else if (priv->phy_mode[port] == PHY_INTERFACE_MODE_2500BASEX)
- mac[port].speed = priv->info->port_speed[SJA1105_SPEED_2500MBPS];
- else
- mac[port].speed = speed;
+ speed = priv->info->port_speed[SJA1105_SPEED_2500MBPS];
+
+ mac[port].speed = speed;
+
+ return 0;
+}
+
+/* Write the MAC Configuration Table entry and, if necessary, the CGU settings,
+ * after a link speedchange for this port.
+ */
+static int sja1105_set_port_config(struct sja1105_private *priv, int port)
+{
+ struct sja1105_mac_config_entry *mac;
+ struct device *dev = priv->ds->dev;
+ int rc;
+
+ /* On P/Q/R/S, one can read from the device via the MAC reconfiguration
+ * tables. On E/T, MAC reconfig tables are not readable, only writable.
+ * We have to *know* what the MAC looks like. For the sake of keeping
+ * the code common, we'll use the static configuration tables as a
+ * reasonable approximation for both E/T and P/Q/R/S.
+ */
+ mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries;
/* Write to the dynamic reconfiguration tables */
rc = sja1105_dynamic_config_write(priv, BLK_IDX_MAC_CONFIG, port,
@@ -1390,7 +1392,8 @@ static void sja1105_mac_link_up(struct phylink_config *config,
struct sja1105_private *priv = dp->ds->priv;
int port = dp->index;
- sja1105_adjust_port_config(priv, port, speed);
+ if (!sja1105_set_port_speed(priv, port, speed))
+ sja1105_set_port_config(priv, port);
sja1105_inhibit_tx(priv, BIT(port), false);
}
@@ -2293,8 +2296,8 @@ int sja1105_static_config_reload(struct sja1105_private *priv,
{
struct ptp_system_timestamp ptp_sts_before;
struct ptp_system_timestamp ptp_sts_after;
- int speed_mbps[SJA1105_MAX_NUM_PORTS];
u16 bmcr[SJA1105_MAX_NUM_PORTS] = {0};
+ u64 mac_speed[SJA1105_MAX_NUM_PORTS];
struct sja1105_mac_config_entry *mac;
struct dsa_switch *ds = priv->ds;
s64 t1, t2, t3, t4;
@@ -2307,14 +2310,13 @@ int sja1105_static_config_reload(struct sja1105_private *priv,
mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries;
- /* Back up the dynamic link speed changed by sja1105_adjust_port_config
+ /* Back up the dynamic link speed changed by sja1105_set_port_speed()
* in order to temporarily restore it to SJA1105_SPEED_AUTO - which the
* switch wants to see in the static config in order to allow us to
* change it through the dynamic interface later.
*/
for (i = 0; i < ds->num_ports; i++) {
- speed_mbps[i] = sja1105_port_speed_to_ethtool(priv,
- mac[i].speed);
+ mac_speed[i] = mac[i].speed;
mac[i].speed = priv->info->port_speed[SJA1105_SPEED_AUTO];
if (priv->xpcs[i])
@@ -2377,7 +2379,8 @@ int sja1105_static_config_reload(struct sja1105_private *priv,
struct dw_xpcs *xpcs = priv->xpcs[i];
unsigned int neg_mode;
- rc = sja1105_adjust_port_config(priv, i, speed_mbps[i]);
+ mac[i].speed = mac_speed[i];
+ rc = sja1105_set_port_config(priv, i);
if (rc < 0)
goto out;
The static configuration reload saves the port speed in the static configuration tables by first converting it from the internal respresentation to the SPEED_xxx ethtool representation, and then converts it back to restore the setting. This is because sja1105_adjust_port_config() takes the speed as SPEED_xxx. However, this is unnecessarily complex. If we split sja1105_adjust_port_config() up, we can simply save and restore the mac[port].speed member in the static configuration tables. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> --- Changes since rfc: - added () to function name - fixed local variable order drivers/net/dsa/sja1105/sja1105_main.c | 65 ++++++++++++++------------ 1 file changed, 34 insertions(+), 31 deletions(-)