[RFC,net-next,23/23] net: stmmac: convert to phylink managed EEE support

Commit Message

Russell King (Oracle) Nov. 26, 2024, 12:54 p.m. UTC

Convert stmmac to use phylink managed EEE support rather than delving
into phylib.

Signed-off-by: Russell King (Oracle) <[e-mail]>
---
 .../net/ethernet/stmicro/stmmac/stmmac_main.c | 50 +++++++++++++++----
 1 file changed, 39 insertions(+), 11 deletions(-)

Patch

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 66a43a9aa469..39a4f0da82e5 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -973,9 +973,6 @@  static void stmmac_mac_link_down(struct phylink_config *config,
 	struct stmmac_priv *priv = netdev_priv(to_net_dev(config->dev));
 
 	stmmac_mac_set(priv, priv->ioaddr, false);
-	priv->eee_active = false;
-	priv->eee_enabled = stmmac_eee_init(priv);
-	stmmac_set_eee_pls(priv, priv->hw, false);
 
 	if (stmmac_fpe_supported(priv))
 		stmmac_fpe_link_state_handle(priv, false);
@@ -1082,14 +1079,6 @@  static void stmmac_mac_link_up(struct phylink_config *config,
 		writel(ctrl, priv->ioaddr + MAC_CTRL_REG);
 
 	stmmac_mac_set(priv, priv->ioaddr, true);
-	if (phy && priv->dma_cap.eee) {
-		phy_eee_rx_clock_stop(phy, !(priv->plat->flags &
-					     STMMAC_FLAG_RX_CLK_RUNS_IN_LPI));
-		priv->eee_active = phy->enable_tx_lpi;
-		priv->eee_enabled = stmmac_eee_init(priv);
-		priv->tx_lpi_timer = phy->eee_cfg.tx_lpi_timer;
-		stmmac_set_eee_pls(priv, priv->hw, true);
-	}
 
 	if (stmmac_fpe_supported(priv))
 		stmmac_fpe_link_state_handle(priv, true);
@@ -1098,12 +1087,34 @@  static void stmmac_mac_link_up(struct phylink_config *config,
 		stmmac_hwtstamp_correct_latency(priv, priv);
 }
 
+static void stmmac_mac_disable_tx_lpi(struct phylink_config *config)
+{
+	struct stmmac_priv *priv = netdev_priv(to_net_dev(config->dev));
+
+	priv->eee_active = false;
+	priv->eee_enabled = stmmac_eee_init(priv);
+	stmmac_set_eee_pls(priv, priv->hw, false);
+}
+
+static void stmmac_mac_enable_tx_lpi(struct phylink_config *config, u32 timer,
+				     bool tx_clk_stop)
+{
+	struct stmmac_priv *priv = netdev_priv(to_net_dev(config->dev));
+
+	priv->eee_active = true;
+	priv->eee_enabled = stmmac_eee_init(priv);
+	priv->tx_lpi_timer = timer;
+	stmmac_set_eee_pls(priv, priv->hw, true);
+}
+
 static const struct phylink_mac_ops stmmac_phylink_mac_ops = {
 	.mac_get_caps = stmmac_mac_get_caps,
 	.mac_select_pcs = stmmac_mac_select_pcs,
 	.mac_config = stmmac_mac_config,
 	.mac_link_down = stmmac_mac_link_down,
 	.mac_link_up = stmmac_mac_link_up,
+	.mac_disable_tx_lpi = stmmac_mac_disable_tx_lpi,
+	.mac_mac_enable_tx_lpi = stmmac_mac_enable_tx_lpi,
 };
 
 /**
@@ -1216,6 +1227,18 @@  static int stmmac_phy_setup(struct stmmac_priv *priv)
 	/* Stmmac always requires an RX clock for hardware initialization */
 	priv->phylink_config.mac_requires_rxc = true;
 
+	if (!(priv->plat->flags & STMMAC_FLAG_RX_CLK_RUNS_IN_LPI))
+		priv->phylink_config.eee_rx_clk_stop_enable = true;
+
+	if (priv->dma_cap.eee) {
+		/* All full duplex speeds above 100Mbps are supported */
+		priv->phylink_config.lpi_capabilities = ~(MAC_1000FD - 1) |
+							MAC_100FD;
+		priv->phylink_config.lpi_timer_limit_us = U32_MAX;
+		priv->phylink_config.lpi_timer_default = eee_timer * 1000;
+		priv->phylink_config.eee_enabled_default = false;
+	}
+
 	mdio_bus_data = priv->plat->mdio_bus_data;
 	if (mdio_bus_data)
 		priv->phylink_config.default_an_inband =
@@ -1231,6 +1254,11 @@  static int stmmac_phy_setup(struct stmmac_priv *priv)
 		xpcs_get_interfaces(priv->hw->xpcs,
 				    priv->phylink_config.supported_interfaces);
 
+	/* Assume all supported interfaces also support LPI */
+	memcpy(priv->phylink_config.lpi_interfaces,
+	       priv->phylink_config.supported_interfaces,
+	       sizeof(priv->phylink_config.lpi_interfaces));
+
 	fwnode = priv->plat->port_node;
 	if (!fwnode)
 		fwnode = dev_fwnode(priv->device);