| Message ID | b49904649a363f40dc9c4d3fa275e42129562082.1684767562.git.michal.simek@amd.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | arm64: zynqmp: Misc zynqmp changes | expand |
On 5/22/23 16:59, Michal Simek wrote: > TI DP83867 is using strapping based on MIO pins. Tristate setup can > influence PHY address. That's why switch description with ethernet-phy-id > compatible string which enable calling reset. PHY itself setups phy address > after power up or reset. Phy reset is done via gpio. > > Signed-off-by: Michal Simek <michal.simek@amd.com> > --- > > Changes in v2: > - fix typo in commit message > > Checkpatch is reporting issue > warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented > but it should be fully aligned with > Documentation/devicetree/bindings/net/ethernet-phy.yaml > > c&p more details from v1 version: > Phy has some pins which is using for strapping for phy address after phy > reset or power on. Pretty much it is resistor array which based on > datasheet is decoded to certain phy address. > And because some phy pins are also used as data pin for RGMII they are > connected via MIO pins on a silicon. That's why IO block output setting > really matter here because it changes resistor array and it moves phy > address. > That's why there is a need to do proper IO pin setup and after it call phy > reset to get it to address which was decided by PCB designer. > > --- > .../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 23 +++++++++++------ > .../boot/dts/xilinx/zynqmp-zcu102-revB.dts | 25 +++++++++++-------- > .../boot/dts/xilinx/zynqmp-zcu104-revA.dts | 22 ++++++++++------ > .../boot/dts/xilinx/zynqmp-zcu104-revC.dts | 22 ++++++++++------ > .../boot/dts/xilinx/zynqmp-zcu106-revA.dts | 22 ++++++++++------ > .../boot/dts/xilinx/zynqmp-zcu111-revA.dts | 22 ++++++++++------ > 6 files changed, 90 insertions(+), 46 deletions(-) > > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts > index 230ef94d5dcb..f36353a51863 100644 > --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts > +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts > @@ -2,7 +2,8 @@ > /* > * dts file for Xilinx ZynqMP ZCU102 RevA > * > - * (C) Copyright 2015 - 2021, Xilinx, Inc. > + * (C) Copyright 2015 - 2022, Xilinx, Inc. > + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. > * > * Michal Simek <michal.simek@amd.com> > */ > @@ -200,13 +201,19 @@ &gem3 { > phy-mode = "rgmii-id"; > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_gem3_default>; > - phy0: ethernet-phy@21 { > - reg = <21>; > - ti,rx-internal-delay = <0x8>; > - ti,tx-internal-delay = <0xa>; > - ti,fifo-depth = <0x1>; > - ti,dp83867-rxctrl-strap-quirk; > - /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */ > + mdio: mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + phy0: ethernet-phy@21 { > + #phy-cells = <1>; > + compatible = "ethernet-phy-id2000.a231"; > + reg = <21>; > + ti,rx-internal-delay = <0x8>; > + ti,tx-internal-delay = <0xa>; > + ti,fifo-depth = <0x1>; > + ti,dp83867-rxctrl-strap-quirk; > + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; > + }; > }; > }; > > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts > index 63419deb5b33..3c28130909bc 100644 > --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts > +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts > @@ -2,7 +2,8 @@ > /* > * dts file for Xilinx ZynqMP ZCU102 RevB > * > - * (C) Copyright 2016 - 2021, Xilinx, Inc. > + * (C) Copyright 2016 - 2022, Xilinx, Inc. > + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. > * > * Michal Simek <michal.simek@amd.com> > */ > @@ -16,16 +17,20 @@ / { > > &gem3 { > phy-handle = <&phyc>; > - phyc: ethernet-phy@c { > - reg = <0xc>; > - ti,rx-internal-delay = <0x8>; > - ti,tx-internal-delay = <0xa>; > - ti,fifo-depth = <0x1>; > - ti,dp83867-rxctrl-strap-quirk; > - /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */ > + mdio: mdio { > + phyc: ethernet-phy@c { > + #phy-cells = <0x1>; > + compatible = "ethernet-phy-id2000.a231"; > + reg = <0xc>; > + ti,rx-internal-delay = <0x8>; > + ti,tx-internal-delay = <0xa>; > + ti,fifo-depth = <0x1>; > + ti,dp83867-rxctrl-strap-quirk; > + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; > + }; > + /* Cleanup from RevA */ > + /delete-node/ ethernet-phy@21; > }; > - /* Cleanup from RevA */ > - /delete-node/ ethernet-phy@21; > }; > > /* Fix collision with u61 */ > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts > index d178a4f898c9..3fd47725c2c8 100644 > --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts > +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts > @@ -2,7 +2,8 @@ > /* > * dts file for Xilinx ZynqMP ZCU104 > * > - * (C) Copyright 2017 - 2021, Xilinx, Inc. > + * (C) Copyright 2017 - 2022, Xilinx, Inc. > + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. > * > * Michal Simek <michal.simek@amd.com> > */ > @@ -109,12 +110,19 @@ &gem3 { > phy-mode = "rgmii-id"; > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_gem3_default>; > - phy0: ethernet-phy@c { > - reg = <0xc>; > - ti,rx-internal-delay = <0x8>; > - ti,tx-internal-delay = <0xa>; > - ti,fifo-depth = <0x1>; > - ti,dp83867-rxctrl-strap-quirk; > + mdio: mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + phy0: ethernet-phy@c { > + #phy-cells = <1>; > + compatible = "ethernet-phy-id2000.a231"; > + reg = <0xc>; > + ti,rx-internal-delay = <0x8>; > + ti,tx-internal-delay = <0xa>; > + ti,fifo-depth = <0x1>; > + ti,dp83867-rxctrl-strap-quirk; > + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; > + }; > }; > }; > > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts > index 38b11594c074..4f6429caecff 100644 > --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts > +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts > @@ -2,7 +2,8 @@ > /* > * dts file for Xilinx ZynqMP ZCU104 > * > - * (C) Copyright 2017 - 2021, Xilinx, Inc. > + * (C) Copyright 2017 - 2022, Xilinx, Inc. > + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. > * > * Michal Simek <michal.simek@amd.com> > */ > @@ -114,12 +115,19 @@ &gem3 { > phy-mode = "rgmii-id"; > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_gem3_default>; > - phy0: ethernet-phy@c { > - reg = <0xc>; > - ti,rx-internal-delay = <0x8>; > - ti,tx-internal-delay = <0xa>; > - ti,fifo-depth = <0x1>; > - ti,dp83867-rxctrl-strap-quirk; > + mdio: mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + phy0: ethernet-phy@c { > + #phy-cells = <1>; > + compatible = "ethernet-phy-id2000.a231"; > + reg = <0xc>; > + ti,rx-internal-delay = <0x8>; > + ti,tx-internal-delay = <0xa>; > + ti,fifo-depth = <0x1>; > + ti,dp83867-rxctrl-strap-quirk; > + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; > + }; > }; > }; > > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts > index 8af0879806cf..8c3fa3fe28d5 100644 > --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts > +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts > @@ -2,7 +2,8 @@ > /* > * dts file for Xilinx ZynqMP ZCU106 > * > - * (C) Copyright 2016 - 2021, Xilinx, Inc. > + * (C) Copyright 2016 - 2022, Xilinx, Inc. > + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. > * > * Michal Simek <michal.simek@amd.com> > */ > @@ -212,12 +213,19 @@ &gem3 { > phy-mode = "rgmii-id"; > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_gem3_default>; > - phy0: ethernet-phy@c { > - reg = <0xc>; > - ti,rx-internal-delay = <0x8>; > - ti,tx-internal-delay = <0xa>; > - ti,fifo-depth = <0x1>; > - ti,dp83867-rxctrl-strap-quirk; > + mdio: mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + phy0: ethernet-phy@c { > + #phy-cells = <1>; > + reg = <0xc>; > + compatible = "ethernet-phy-id2000.a231"; > + ti,rx-internal-delay = <0x8>; > + ti,tx-internal-delay = <0xa>; > + ti,fifo-depth = <0x1>; > + ti,dp83867-rxctrl-strap-quirk; > + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; > + }; > }; > }; > > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts > index f76687914e30..0d9b6081dff6 100644 > --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts > +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts > @@ -2,7 +2,8 @@ > /* > * dts file for Xilinx ZynqMP ZCU111 > * > - * (C) Copyright 2017 - 2021, Xilinx, Inc. > + * (C) Copyright 2017 - 2022, Xilinx, Inc. > + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. > * > * Michal Simek <michal.simek@amd.com> > */ > @@ -172,12 +173,19 @@ &gem3 { > phy-mode = "rgmii-id"; > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_gem3_default>; > - phy0: ethernet-phy@c { > - reg = <0xc>; > - ti,rx-internal-delay = <0x8>; > - ti,tx-internal-delay = <0xa>; > - ti,fifo-depth = <0x1>; > - ti,dp83867-rxctrl-strap-quirk; > + mdio: mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + phy0: ethernet-phy@c { > + #phy-cells = <1>; > + compatible = "ethernet-phy-id2000.a231"; > + reg = <0xc>; > + ti,rx-internal-delay = <0x8>; > + ti,tx-internal-delay = <0xa>; > + ti,fifo-depth = <0x1>; > + ti,dp83867-rxctrl-strap-quirk; > + reset-gpios = <&tca6416_u22 6 GPIO_ACTIVE_LOW>; > + }; > }; > }; > Applied. M
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts index 230ef94d5dcb..f36353a51863 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts @@ -2,7 +2,8 @@ /* * dts file for Xilinx ZynqMP ZCU102 RevA * - * (C) Copyright 2015 - 2021, Xilinx, Inc. + * (C) Copyright 2015 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * * Michal Simek <michal.simek@amd.com> */ @@ -200,13 +201,19 @@ &gem3 { phy-mode = "rgmii-id"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gem3_default>; - phy0: ethernet-phy@21 { - reg = <21>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; - /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */ + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@21 { + #phy-cells = <1>; + compatible = "ethernet-phy-id2000.a231"; + reg = <21>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; + }; }; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts index 63419deb5b33..3c28130909bc 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts @@ -2,7 +2,8 @@ /* * dts file for Xilinx ZynqMP ZCU102 RevB * - * (C) Copyright 2016 - 2021, Xilinx, Inc. + * (C) Copyright 2016 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * * Michal Simek <michal.simek@amd.com> */ @@ -16,16 +17,20 @@ / { &gem3 { phy-handle = <&phyc>; - phyc: ethernet-phy@c { - reg = <0xc>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; - /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */ + mdio: mdio { + phyc: ethernet-phy@c { + #phy-cells = <0x1>; + compatible = "ethernet-phy-id2000.a231"; + reg = <0xc>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; + }; + /* Cleanup from RevA */ + /delete-node/ ethernet-phy@21; }; - /* Cleanup from RevA */ - /delete-node/ ethernet-phy@21; }; /* Fix collision with u61 */ diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts index d178a4f898c9..3fd47725c2c8 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts @@ -2,7 +2,8 @@ /* * dts file for Xilinx ZynqMP ZCU104 * - * (C) Copyright 2017 - 2021, Xilinx, Inc. + * (C) Copyright 2017 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * * Michal Simek <michal.simek@amd.com> */ @@ -109,12 +110,19 @@ &gem3 { phy-mode = "rgmii-id"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gem3_default>; - phy0: ethernet-phy@c { - reg = <0xc>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@c { + #phy-cells = <1>; + compatible = "ethernet-phy-id2000.a231"; + reg = <0xc>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; + }; }; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts index 38b11594c074..4f6429caecff 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts @@ -2,7 +2,8 @@ /* * dts file for Xilinx ZynqMP ZCU104 * - * (C) Copyright 2017 - 2021, Xilinx, Inc. + * (C) Copyright 2017 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * * Michal Simek <michal.simek@amd.com> */ @@ -114,12 +115,19 @@ &gem3 { phy-mode = "rgmii-id"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gem3_default>; - phy0: ethernet-phy@c { - reg = <0xc>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@c { + #phy-cells = <1>; + compatible = "ethernet-phy-id2000.a231"; + reg = <0xc>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; + }; }; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts index 8af0879806cf..8c3fa3fe28d5 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts @@ -2,7 +2,8 @@ /* * dts file for Xilinx ZynqMP ZCU106 * - * (C) Copyright 2016 - 2021, Xilinx, Inc. + * (C) Copyright 2016 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * * Michal Simek <michal.simek@amd.com> */ @@ -212,12 +213,19 @@ &gem3 { phy-mode = "rgmii-id"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gem3_default>; - phy0: ethernet-phy@c { - reg = <0xc>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@c { + #phy-cells = <1>; + reg = <0xc>; + compatible = "ethernet-phy-id2000.a231"; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; + }; }; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts index f76687914e30..0d9b6081dff6 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts @@ -2,7 +2,8 @@ /* * dts file for Xilinx ZynqMP ZCU111 * - * (C) Copyright 2017 - 2021, Xilinx, Inc. + * (C) Copyright 2017 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * * Michal Simek <michal.simek@amd.com> */ @@ -172,12 +173,19 @@ &gem3 { phy-mode = "rgmii-id"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gem3_default>; - phy0: ethernet-phy@c { - reg = <0xc>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@c { + #phy-cells = <1>; + compatible = "ethernet-phy-id2000.a231"; + reg = <0xc>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u22 6 GPIO_ACTIVE_LOW>; + }; }; };
TI DP83867 is using strapping based on MIO pins. Tristate setup can influence PHY address. That's why switch description with ethernet-phy-id compatible string which enable calling reset. PHY itself setups phy address after power up or reset. Phy reset is done via gpio. Signed-off-by: Michal Simek <michal.simek@amd.com> --- Changes in v2: - fix typo in commit message Checkpatch is reporting issue warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented but it should be fully aligned with Documentation/devicetree/bindings/net/ethernet-phy.yaml c&p more details from v1 version: Phy has some pins which is using for strapping for phy address after phy reset or power on. Pretty much it is resistor array which based on datasheet is decoded to certain phy address. And because some phy pins are also used as data pin for RGMII they are connected via MIO pins on a silicon. That's why IO block output setting really matter here because it changes resistor array and it moves phy address. That's why there is a need to do proper IO pin setup and after it call phy reset to get it to address which was decided by PCB designer. --- .../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 23 +++++++++++------ .../boot/dts/xilinx/zynqmp-zcu102-revB.dts | 25 +++++++++++-------- .../boot/dts/xilinx/zynqmp-zcu104-revA.dts | 22 ++++++++++------ .../boot/dts/xilinx/zynqmp-zcu104-revC.dts | 22 ++++++++++------ .../boot/dts/xilinx/zynqmp-zcu106-revA.dts | 22 ++++++++++------ .../boot/dts/xilinx/zynqmp-zcu111-revA.dts | 22 ++++++++++------ 6 files changed, 90 insertions(+), 46 deletions(-)