diff mbox series

[v10,1/2] dt-bindings: display/bridge: Add binding for NWL mipi dsi host controller

Message ID c7fd138e00608a108dae3651ab10d583a60040fc.1584730033.git.agx@sigxcpu.org (mailing list archive)
State New, archived
Headers show
Series drm: bridge: Add NWL MIPI DSI host controller support | expand

Commit Message

Guido Günther March 20, 2020, 6:49 p.m. UTC
The Northwest Logic MIPI DSI IP core can be found in NXPs i.MX8 SoCs.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Tested-by: Robert Chiras <robert.chiras@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
---
 .../bindings/display/bridge/nwl-dsi.yaml      | 216 ++++++++++++++++++
 1 file changed, 216 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml

Comments

Fabio Estevam March 24, 2020, 7:34 p.m. UTC | #1
On Fri, Mar 20, 2020 at 3:49 PM Guido Günther <agx@sigxcpu.org> wrote:
>
> The Northwest Logic MIPI DSI IP core can be found in NXPs i.MX8 SoCs.
>
> Signed-off-by: Guido Günther <agx@sigxcpu.org>
> Tested-by: Robert Chiras <robert.chiras@nxp.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> Acked-by: Sam Ravnborg <sam@ravnborg.org>

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sam Ravnborg April 8, 2020, 5:32 p.m. UTC | #2
Hi Guido.

We discussed this binding briefly on IRC:

19:28 <pinchartl> port 0 is defined as
19:28 <pinchartl> +          Input port node to receive pixel data from the
19:28 <pinchartl> +          display controller. Exactly one endpoint must be
19:28 <pinchartl> +          specified.
19:28 <pinchartl> then there's two endpoints,


On Fri, Mar 20, 2020 at 07:49:09PM +0100, Guido Günther wrote:
> The Northwest Logic MIPI DSI IP core can be found in NXPs i.MX8 SoCs.
> 
> Signed-off-by: Guido Günther <agx@sigxcpu.org>
> Tested-by: Robert Chiras <robert.chiras@nxp.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> Acked-by: Sam Ravnborg <sam@ravnborg.org>
> ---
>  .../bindings/display/bridge/nwl-dsi.yaml      | 216 ++++++++++++++++++
>  1 file changed, 216 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
> 
> diff --git a/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml b/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
> new file mode 100644
> index 000000000000..ec1e7e12719d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
> @@ -0,0 +1,216 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/bridge/nwl-dsi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Northwest Logic MIPI-DSI controller on i.MX SoCs
> +
> +maintainers:
> +  - Guido Gúnther <agx@sigxcpu.org>
> +  - Robert Chiras <robert.chiras@nxp.com>
> +
> +description: |
> +  NWL MIPI-DSI host controller found on i.MX8 platforms. This is a dsi bridge for
> +  the SOCs NWL MIPI-DSI host controller.
> +
> +properties:
> +  compatible:
> +    const: fsl,imx8mq-nwl-dsi
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  '#address-cells':
> +    const: 1
> +
> +  '#size-cells':
> +    const: 0
> +
> +  clocks:
> +    items:
> +      - description: DSI core clock
> +      - description: RX_ESC clock (used in escape mode)
> +      - description: TX_ESC clock (used in escape mode)
> +      - description: PHY_REF clock
> +      - description: LCDIF clock
> +
> +  clock-names:
> +    items:
> +      - const: core
> +      - const: rx_esc
> +      - const: tx_esc
> +      - const: phy_ref
> +      - const: lcdif
> +
> +  mux-controls:
> +    description:
> +      mux controller node to use for operating the input mux
> +
> +  phys:
> +    maxItems: 1
> +    description:
> +      A phandle to the phy module representing the DPHY
> +
> +  phy-names:
> +    items:
> +      - const: dphy
> +
> +  power-domains:
> +    maxItems: 1
> +
> +  resets:
> +    items:
> +      - description: dsi byte reset line
> +      - description: dsi dpi reset line
> +      - description: dsi esc reset line
> +      - description: dsi pclk reset line
> +
> +  reset-names:
> +    items:
> +      - const: byte
> +      - const: dpi
> +      - const: esc
> +      - const: pclk
> +
> +  ports:
> +    type: object
> +    description:
> +      A node containing DSI input & output port nodes with endpoint
> +      definitions as documented in
> +      Documentation/devicetree/bindings/graph.txt.
> +    properties:
> +      port@0:
> +        type: object
> +        description:
> +          Input port node to receive pixel data from the
> +          display controller. Exactly one endpoint must be
> +          specified.
> +        properties:
> +          '#address-cells':
> +            const: 1
> +
> +          '#size-cells':
> +            const: 0
> +
> +          endpoint@0:
> +            description: sub-node describing the input from LCDIF
> +            type: object
> +
> +          endpoint@1:
> +            description: sub-node describing the input from DCSS
> +            type: object
> +
> +          reg:
> +            const: 0
> +
> +        required:
> +          - '#address-cells'
> +          - '#size-cells'
> +          - reg
> +        additionalProperties: false
> +
> +      port@1:
> +        type: object
> +        description:
> +          DSI output port node to the panel or the next bridge
> +          in the chain
> +
> +      '#address-cells':
> +        const: 1
> +
> +      '#size-cells':
> +        const: 0
> +
> +    required:
> +      - '#address-cells'
> +      - '#size-cells'
> +      - port@0
> +      - port@1
> +
> +    additionalProperties: false

For the casual reader the above confuses.
Assuming the binding is correct, can we have the comment updated.

	Sam

> +
> +patternProperties:
> +  "^panel@[0-9]+$":
> +    type: object
> +
> +required:
> +  - '#address-cells'
> +  - '#size-cells'
> +  - clock-names
> +  - clocks
> +  - compatible
> +  - interrupts
> +  - mux-controls
> +  - phy-names
> +  - phys
> +  - ports
> +  - reg
> +  - reset-names
> +  - resets
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> +
> +   #include <dt-bindings/clock/imx8mq-clock.h>
> +   #include <dt-bindings/interrupt-controller/arm-gic.h>
> +   #include <dt-bindings/reset/imx8mq-reset.h>
> +
> +   mipi_dsi: mipi_dsi@30a00000 {
> +              #address-cells = <1>;
> +              #size-cells = <0>;
> +              compatible = "fsl,imx8mq-nwl-dsi";
> +              reg = <0x30A00000 0x300>;
> +              clocks = <&clk IMX8MQ_CLK_DSI_CORE>,
> +                       <&clk IMX8MQ_CLK_DSI_AHB>,
> +                       <&clk IMX8MQ_CLK_DSI_IPG_DIV>,
> +                       <&clk IMX8MQ_CLK_DSI_PHY_REF>,
> +                       <&clk IMX8MQ_CLK_LCDIF_PIXEL>;
> +              clock-names = "core", "rx_esc", "tx_esc", "phy_ref", "lcdif";
> +              interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
> +              mux-controls = <&mux 0>;
> +              power-domains = <&pgc_mipi>;
> +              resets = <&src IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N>,
> +                       <&src IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N>,
> +                       <&src IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N>,
> +                       <&src IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N>;
> +              reset-names = "byte", "dpi", "esc", "pclk";
> +              phys = <&dphy>;
> +              phy-names = "dphy";
> +
> +              panel@0 {
> +                      compatible = "rocktech,jh057n00900";
> +                      reg = <0>;
> +                      port@0 {
> +                           panel_in: endpoint {
> +                                     remote-endpoint = <&mipi_dsi_out>;
> +                           };
> +                      };
> +              };
> +
> +              ports {
> +                    #address-cells = <1>;
> +                    #size-cells = <0>;
> +
> +                    port@0 {
> +                           #size-cells = <0>;
> +                           #address-cells = <1>;
> +                           reg = <0>;
> +                           mipi_dsi_in: endpoint@0 {
> +                                        reg = <0>;
> +                                        remote-endpoint = <&lcdif_mipi_dsi>;
> +                           };
> +                    };
> +                    port@1 {
> +                           reg = <1>;
> +                           mipi_dsi_out: endpoint {
> +                                         remote-endpoint = <&panel_in>;
> +                           };
> +                    };
> +              };
> +      };
> -- 
> 2.23.0
Guido Günther April 9, 2020, 10:42 a.m. UTC | #3
Hi,
On Wed, Apr 08, 2020 at 07:32:58PM +0200, Sam Ravnborg wrote:
> Hi Guido.
> 
> We discussed this binding briefly on IRC:
> 
> 19:28 <pinchartl> port 0 is defined as
> 19:28 <pinchartl> +          Input port node to receive pixel data from the
> 19:28 <pinchartl> +          display controller. Exactly one endpoint must be
> 19:28 <pinchartl> +          specified.
> 19:28 <pinchartl> then there's two endpoints,

There's only a single one allowed due to

  https://lore.kernel.org/linux-arm-kernel/c86b7ca2-7799-eafd-c380-e4b551520837@samsung.com/

Back when doing that i couldn't figure out a way how to specify this but
I've figured it out now.
Cheers,
 -- Guido

> 
> 
> On Fri, Mar 20, 2020 at 07:49:09PM +0100, Guido Günther wrote:
> > The Northwest Logic MIPI DSI IP core can be found in NXPs i.MX8 SoCs.
> > 
> > Signed-off-by: Guido Günther <agx@sigxcpu.org>
> > Tested-by: Robert Chiras <robert.chiras@nxp.com>
> > Reviewed-by: Rob Herring <robh@kernel.org>
> > Acked-by: Sam Ravnborg <sam@ravnborg.org>
> > ---
> >  .../bindings/display/bridge/nwl-dsi.yaml      | 216 ++++++++++++++++++
> >  1 file changed, 216 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml b/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
> > new file mode 100644
> > index 000000000000..ec1e7e12719d
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
> > @@ -0,0 +1,216 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/display/bridge/nwl-dsi.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Northwest Logic MIPI-DSI controller on i.MX SoCs
> > +
> > +maintainers:
> > +  - Guido Gúnther <agx@sigxcpu.org>
> > +  - Robert Chiras <robert.chiras@nxp.com>
> > +
> > +description: |
> > +  NWL MIPI-DSI host controller found on i.MX8 platforms. This is a dsi bridge for
> > +  the SOCs NWL MIPI-DSI host controller.
> > +
> > +properties:
> > +  compatible:
> > +    const: fsl,imx8mq-nwl-dsi
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  interrupts:
> > +    maxItems: 1
> > +
> > +  '#address-cells':
> > +    const: 1
> > +
> > +  '#size-cells':
> > +    const: 0
> > +
> > +  clocks:
> > +    items:
> > +      - description: DSI core clock
> > +      - description: RX_ESC clock (used in escape mode)
> > +      - description: TX_ESC clock (used in escape mode)
> > +      - description: PHY_REF clock
> > +      - description: LCDIF clock
> > +
> > +  clock-names:
> > +    items:
> > +      - const: core
> > +      - const: rx_esc
> > +      - const: tx_esc
> > +      - const: phy_ref
> > +      - const: lcdif
> > +
> > +  mux-controls:
> > +    description:
> > +      mux controller node to use for operating the input mux
> > +
> > +  phys:
> > +    maxItems: 1
> > +    description:
> > +      A phandle to the phy module representing the DPHY
> > +
> > +  phy-names:
> > +    items:
> > +      - const: dphy
> > +
> > +  power-domains:
> > +    maxItems: 1
> > +
> > +  resets:
> > +    items:
> > +      - description: dsi byte reset line
> > +      - description: dsi dpi reset line
> > +      - description: dsi esc reset line
> > +      - description: dsi pclk reset line
> > +
> > +  reset-names:
> > +    items:
> > +      - const: byte
> > +      - const: dpi
> > +      - const: esc
> > +      - const: pclk
> > +
> > +  ports:
> > +    type: object
> > +    description:
> > +      A node containing DSI input & output port nodes with endpoint
> > +      definitions as documented in
> > +      Documentation/devicetree/bindings/graph.txt.
> > +    properties:
> > +      port@0:
> > +        type: object
> > +        description:
> > +          Input port node to receive pixel data from the
> > +          display controller. Exactly one endpoint must be
> > +          specified.
> > +        properties:
> > +          '#address-cells':
> > +            const: 1
> > +
> > +          '#size-cells':
> > +            const: 0
> > +
> > +          endpoint@0:
> > +            description: sub-node describing the input from LCDIF
> > +            type: object
> > +
> > +          endpoint@1:
> > +            description: sub-node describing the input from DCSS
> > +            type: object
> > +
> > +          reg:
> > +            const: 0
> > +
> > +        required:
> > +          - '#address-cells'
> > +          - '#size-cells'
> > +          - reg
> > +        additionalProperties: false
> > +
> > +      port@1:
> > +        type: object
> > +        description:
> > +          DSI output port node to the panel or the next bridge
> > +          in the chain
> > +
> > +      '#address-cells':
> > +        const: 1
> > +
> > +      '#size-cells':
> > +        const: 0
> > +
> > +    required:
> > +      - '#address-cells'
> > +      - '#size-cells'
> > +      - port@0
> > +      - port@1
> > +
> > +    additionalProperties: false
> 
> For the casual reader the above confuses.
> Assuming the binding is correct, can we have the comment updated.
> 
> 	Sam
> 
> > +
> > +patternProperties:
> > +  "^panel@[0-9]+$":
> > +    type: object
> > +
> > +required:
> > +  - '#address-cells'
> > +  - '#size-cells'
> > +  - clock-names
> > +  - clocks
> > +  - compatible
> > +  - interrupts
> > +  - mux-controls
> > +  - phy-names
> > +  - phys
> > +  - ports
> > +  - reg
> > +  - reset-names
> > +  - resets
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > + - |
> > +
> > +   #include <dt-bindings/clock/imx8mq-clock.h>
> > +   #include <dt-bindings/interrupt-controller/arm-gic.h>
> > +   #include <dt-bindings/reset/imx8mq-reset.h>
> > +
> > +   mipi_dsi: mipi_dsi@30a00000 {
> > +              #address-cells = <1>;
> > +              #size-cells = <0>;
> > +              compatible = "fsl,imx8mq-nwl-dsi";
> > +              reg = <0x30A00000 0x300>;
> > +              clocks = <&clk IMX8MQ_CLK_DSI_CORE>,
> > +                       <&clk IMX8MQ_CLK_DSI_AHB>,
> > +                       <&clk IMX8MQ_CLK_DSI_IPG_DIV>,
> > +                       <&clk IMX8MQ_CLK_DSI_PHY_REF>,
> > +                       <&clk IMX8MQ_CLK_LCDIF_PIXEL>;
> > +              clock-names = "core", "rx_esc", "tx_esc", "phy_ref", "lcdif";
> > +              interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
> > +              mux-controls = <&mux 0>;
> > +              power-domains = <&pgc_mipi>;
> > +              resets = <&src IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N>,
> > +                       <&src IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N>,
> > +                       <&src IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N>,
> > +                       <&src IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N>;
> > +              reset-names = "byte", "dpi", "esc", "pclk";
> > +              phys = <&dphy>;
> > +              phy-names = "dphy";
> > +
> > +              panel@0 {
> > +                      compatible = "rocktech,jh057n00900";
> > +                      reg = <0>;
> > +                      port@0 {
> > +                           panel_in: endpoint {
> > +                                     remote-endpoint = <&mipi_dsi_out>;
> > +                           };
> > +                      };
> > +              };
> > +
> > +              ports {
> > +                    #address-cells = <1>;
> > +                    #size-cells = <0>;
> > +
> > +                    port@0 {
> > +                           #size-cells = <0>;
> > +                           #address-cells = <1>;
> > +                           reg = <0>;
> > +                           mipi_dsi_in: endpoint@0 {
> > +                                        reg = <0>;
> > +                                        remote-endpoint = <&lcdif_mipi_dsi>;
> > +                           };
> > +                    };
> > +                    port@1 {
> > +                           reg = <1>;
> > +                           mipi_dsi_out: endpoint {
> > +                                         remote-endpoint = <&panel_in>;
> > +                           };
> > +                    };
> > +              };
> > +      };
> > -- 
> > 2.23.0
>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml b/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
new file mode 100644
index 000000000000..ec1e7e12719d
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml
@@ -0,0 +1,216 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/nwl-dsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Northwest Logic MIPI-DSI controller on i.MX SoCs
+
+maintainers:
+  - Guido Gúnther <agx@sigxcpu.org>
+  - Robert Chiras <robert.chiras@nxp.com>
+
+description: |
+  NWL MIPI-DSI host controller found on i.MX8 platforms. This is a dsi bridge for
+  the SOCs NWL MIPI-DSI host controller.
+
+properties:
+  compatible:
+    const: fsl,imx8mq-nwl-dsi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  clocks:
+    items:
+      - description: DSI core clock
+      - description: RX_ESC clock (used in escape mode)
+      - description: TX_ESC clock (used in escape mode)
+      - description: PHY_REF clock
+      - description: LCDIF clock
+
+  clock-names:
+    items:
+      - const: core
+      - const: rx_esc
+      - const: tx_esc
+      - const: phy_ref
+      - const: lcdif
+
+  mux-controls:
+    description:
+      mux controller node to use for operating the input mux
+
+  phys:
+    maxItems: 1
+    description:
+      A phandle to the phy module representing the DPHY
+
+  phy-names:
+    items:
+      - const: dphy
+
+  power-domains:
+    maxItems: 1
+
+  resets:
+    items:
+      - description: dsi byte reset line
+      - description: dsi dpi reset line
+      - description: dsi esc reset line
+      - description: dsi pclk reset line
+
+  reset-names:
+    items:
+      - const: byte
+      - const: dpi
+      - const: esc
+      - const: pclk
+
+  ports:
+    type: object
+    description:
+      A node containing DSI input & output port nodes with endpoint
+      definitions as documented in
+      Documentation/devicetree/bindings/graph.txt.
+    properties:
+      port@0:
+        type: object
+        description:
+          Input port node to receive pixel data from the
+          display controller. Exactly one endpoint must be
+          specified.
+        properties:
+          '#address-cells':
+            const: 1
+
+          '#size-cells':
+            const: 0
+
+          endpoint@0:
+            description: sub-node describing the input from LCDIF
+            type: object
+
+          endpoint@1:
+            description: sub-node describing the input from DCSS
+            type: object
+
+          reg:
+            const: 0
+
+        required:
+          - '#address-cells'
+          - '#size-cells'
+          - reg
+        additionalProperties: false
+
+      port@1:
+        type: object
+        description:
+          DSI output port node to the panel or the next bridge
+          in the chain
+
+      '#address-cells':
+        const: 1
+
+      '#size-cells':
+        const: 0
+
+    required:
+      - '#address-cells'
+      - '#size-cells'
+      - port@0
+      - port@1
+
+    additionalProperties: false
+
+patternProperties:
+  "^panel@[0-9]+$":
+    type: object
+
+required:
+  - '#address-cells'
+  - '#size-cells'
+  - clock-names
+  - clocks
+  - compatible
+  - interrupts
+  - mux-controls
+  - phy-names
+  - phys
+  - ports
+  - reg
+  - reset-names
+  - resets
+
+additionalProperties: false
+
+examples:
+ - |
+
+   #include <dt-bindings/clock/imx8mq-clock.h>
+   #include <dt-bindings/interrupt-controller/arm-gic.h>
+   #include <dt-bindings/reset/imx8mq-reset.h>
+
+   mipi_dsi: mipi_dsi@30a00000 {
+              #address-cells = <1>;
+              #size-cells = <0>;
+              compatible = "fsl,imx8mq-nwl-dsi";
+              reg = <0x30A00000 0x300>;
+              clocks = <&clk IMX8MQ_CLK_DSI_CORE>,
+                       <&clk IMX8MQ_CLK_DSI_AHB>,
+                       <&clk IMX8MQ_CLK_DSI_IPG_DIV>,
+                       <&clk IMX8MQ_CLK_DSI_PHY_REF>,
+                       <&clk IMX8MQ_CLK_LCDIF_PIXEL>;
+              clock-names = "core", "rx_esc", "tx_esc", "phy_ref", "lcdif";
+              interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+              mux-controls = <&mux 0>;
+              power-domains = <&pgc_mipi>;
+              resets = <&src IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N>,
+                       <&src IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N>,
+                       <&src IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N>,
+                       <&src IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N>;
+              reset-names = "byte", "dpi", "esc", "pclk";
+              phys = <&dphy>;
+              phy-names = "dphy";
+
+              panel@0 {
+                      compatible = "rocktech,jh057n00900";
+                      reg = <0>;
+                      port@0 {
+                           panel_in: endpoint {
+                                     remote-endpoint = <&mipi_dsi_out>;
+                           };
+                      };
+              };
+
+              ports {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    port@0 {
+                           #size-cells = <0>;
+                           #address-cells = <1>;
+                           reg = <0>;
+                           mipi_dsi_in: endpoint@0 {
+                                        reg = <0>;
+                                        remote-endpoint = <&lcdif_mipi_dsi>;
+                           };
+                    };
+                    port@1 {
+                           reg = <1>;
+                           mipi_dsi_out: endpoint {
+                                         remote-endpoint = <&panel_in>;
+                           };
+                    };
+              };
+      };